共查询到20条相似文献,搜索用时 296 毫秒
1.
飞机弹射起飞过程油箱内燃油晃动剧烈,对飞机的操稳特性、结构强度和油量测量性能等产生较大影响。针对飞机弹射起飞过程中,过载和俯仰角度短时相叠加,且变化剧烈难以试验验证的特点,基于单相流体体积法构建油箱燃油晃动特性模型,开展了半油状态下某多隔板扁平形式典型机翼油箱燃油晃动特性数值模拟仿真研究,分析了燃油重心、传感器浸油高度以及结构框板开孔流通能力等自由液面瞬时急剧变化特征。结果表明,在飞机大过载弹射起飞过程中,机动加载阶段,燃油重心快速后移;快速卸载阶段,存在巨大的瞬时燃油冲击力;油量传感器和输油口布局应充分考虑自由液面剧烈变化影响。文中研究成果,可为该运行场景下燃油及相关系统结构的设计与特性影响分析提供参考依据。 相似文献
2.
3.
油箱容器除承受油的静止压力外,还承受由油的晃动引起的动载荷。这个动载荷随油箱运动状态和运动时间的变化而不同,有燃油晃动和燃油冲击之分,下面仅就燃油晃动问题进行讨论,通过一些假设,试图得到油箱设计所需要的动载荷。 如果油箱容器较大,则晃动的液体仅是液体表面以下的一部分,而较深部分的液体,则随容器一起运动。因此,这部分液体可视为一个刚体(这种理论有专门论述,这里不讨论)。如果油箱容器不大或者油箱大但油量较少时,可视为全部油量晃动。由于晃动,则油箱的半面油表面提高,位能增加;当此液表面恢复原状态时,动能增加。由于惯性,液体向油箱另一半面晃去。 相似文献
4.
叶休乃 《航空标准化与质量》1986,(1)
飞机油箱在飞机飞行、起飞着陆过程中,因气动紊流、发动机转子的不平衡、液压泵引起的脉动、武器的发射、地面凹凸不平等原因引起振动,再加上油箱内油液晃动的影响,能使油箱结构连接件松动,结构局部磨损或产生裂纹而造成泄漏,将影响飞机的飞行安全。为此需对油箱结构进行模拟使用条件的环境振动试验来验证其是否具有足够的耐振强度,在振动条件下是否能可靠地工作。 相似文献
5.
6.
飞机执行机动飞行时整体处于大过载状态,此时的油箱晃动流固耦合问题较为复杂。针对这一问题,以某型飞机整体油箱为研究对象,建立ABAQUS与Star-CCM+联合仿真流固耦合方法,对飞机半滚倒转机动行为下的油箱晃动流固耦合效应进行分析,得到了半滚倒转过程中燃油的形态变化,流体域压力以及油箱部件的应力时程曲线等结果,并探究了油箱充液率变化对流固耦合效应的影响。结果表明:机动过载对油箱部件应力应变的影响大于燃油晃动冲击,除上蒙皮外部件应力均随着充液率增加而增加。 相似文献
7.
从适航条款的要求出发,对滑油箱防火试验要求、验证方法、判据准则等进行研究,并对某型民用涡轴发动机滑油箱进行防火试验验证,可为今后其他型号开展滑油箱防火试验提供指导依据。 相似文献
8.
9.
无人机发射过程燃油晃动分析 总被引:1,自引:0,他引:1
《航空科学技术》2016,(1)
本文使用MSC.Dytran有限元分析软件对无人机火箭助推起飞过程中的燃油响应进行了仿真计算。计算中采用任意拉格朗日-欧拉耦合(ALE)方法模拟了燃油和油箱的相互作用。仿真得到油箱内不同油量状态下的无人机起飞姿态的变化和燃油在油箱内的晃动规律,结果表明飞机半油起飞状态姿态变化最为严重。为了改善燃油晃动,研究了几种在油箱中增加隔板的改进设计,并对改进效果进行计算。依据仿真计算结果对油箱布局设计给出了几点建议。本文的仿真计算方法经修改完善后有望用于对无人机起飞段的精确仿真计算。 相似文献
10.
简要阐述飞机结构雷电防护验证试验的种类、主要试验参数、试验方法和试验规范。介绍了飞机典型结构件一复合材料平尾、整体油箱非受力维修口盖、整体油箱通气口盖和复合材料翼梢小翼的雷电防护试验方案设计。 相似文献
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:3,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
13.
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
14.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
15.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
16.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
17.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
18.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献
19.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献