共查询到20条相似文献,搜索用时 78 毫秒
1.
2.
3.
肋片扰流对柱肋通道传热和压损影响 总被引:1,自引:1,他引:0
针对涡轮叶片内部通道上、下游不同冷却结构的相互影响,采用瞬态液晶实验方法研究了上游90°、60°,V形和W形四种肋片诱导产生的入口条件,对柱肋通道传热分布、强化传热水平和压损的影响,并与无肋片(均匀入口条件)的柱肋通道进行了对比。结果表明,相比于无肋片情况的均匀入口条件,肋片诱导的涡流使柱肋通道底面的传热分布在展向变得不均匀。肋片在增强柱肋底面传热的同时降低了通道压损,从而提升柱肋通道的综合换热效率(但整体通道的流动损失增加了)。其中,W形和90°肋片使柱肋通道具有最高的传热效率,其次是V形和60°肋片,不带肋片的情况的综合传热效率最低。 相似文献
4.
5.
采用实验方法对带"V"型沟槽表面通道在不同雷诺数下的流动与换热特性进行了研究.研究结果表明:宽与深均为0.5 mm的沟槽板通道在实验范围内具有明显的减阻效果, 减阻效果随着雷诺数的增大而减小;相比平板通道流动, 低雷诺数范围下(10000相似文献
6.
为了获得大宽高比矩形通道内开孔肋的流动与传热特性,采用数值模拟的方法在开孔肋的肋高e/Dh=0.188、开孔率β=0.131时研究了通道的摩擦系数、努塞尔数等参数随孔排高度和雷诺数的变化规律。结果表明:与实体肋相比,开孔肋能够减小通道的摩擦系数并提高其壁面温度分布的均匀性,但是传热增强因子有所减小;随着孔排高度的提升,通道的摩擦系数单调减小,壁面温度分布的不均匀度增大,而传热增强因子则先增大后减小,因此存在一最优孔排高度(h/e)opt=0.65使开孔肋的强化传热综合指标达到最大值;随着雷诺数的增大,开孔肋通道的摩擦系数缓慢减小、换热逐渐增强,这与实体肋的变化规律是类似的。 相似文献
7.
为了获得带斜孔肋大宽高比矩形通道的强化传热特性,并寻求最佳的孔排倾斜角度,调节孔排倾斜角度和通道雷诺数,使其分别在0°~30°和3×104~9×104范围内变化,通过数值计算系统分析了通道摩擦因数和带肋壁努塞尔数等参数的变化规律.研究发现:相比于常规肋片,新型斜孔肋有效改善了肋片后方紧邻肋片的局部区域的壁面换热,并降低通道的摩擦因数,但传热增强因子有所减小;随着孔排倾斜角度的增大,通道的相对摩擦因子单调升高,传热增强因子则呈现出先升高后降低的变化过程,因此存在着最优孔排倾斜角度为15°,此时斜孔肋的强化传热综合指标达到最大值;随着通道雷诺数的增大,斜孔肋通道的摩擦因数小幅减小,换热则逐渐增强. 相似文献
8.
通过模拟仿真的方法研究了涡轮叶片通道内部V型间断肋的传热特性。主要探究了各结构参数(间断位置,分离肋长度,分离肋后置距离)对通道的传热性能影响。结果表明:相对于传统的扰流肋结构(直肋,60°斜肋,60°V型肋),V型间断肋在壁面平均相对努塞尔数,综合传热系数以及温度分布均匀性上更具优势。通过改变间断参数,能大幅提高V型间断肋的综合传热系数。在研究的参数范围内,当间断位置为2.5 mm,分离肋长度为10.0 mm,分离肋后置距离为9.6 mm时,通道具有最佳的传热性能。在雷诺数为30 000下,与带有直肋的通道相比,优化后的V型间断肋的平均努塞尔数提高了35.75%,综合传热系数上升了28.95%。 相似文献
9.
将冲击冷却技术与肋化表面相结合,研究了一种具有微小W型肋的表面射流冲击冷却结构。通过稳态实验和瞬态热色液晶测试技术来探究光滑靶板和微小W型肋靶板的传热特性。测试时的冲击间距比为1.5,3和5,基于水利直径的雷诺数为15000~40000。结果表明:两种靶板的平均努塞尔数和压力损失均随雷诺数的增加而增加,随冲击间距比的增加而减小。当冲击间距比为1.5时,与光滑靶板相比,微小W型肋靶板的平均努塞尔数提高了5.1%~7.3%,压力损失却几乎不变。但当冲击间距比大于3时,由微小W型肋带来的强化传热效果并不显著。 相似文献
10.
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:3,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
13.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
14.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
15.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
16.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献
17.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献
18.
19.
Wu Xianyu Li Xiaoshan Ding Meng Liu Weidong Wang Zhenguo 《中国航空学报》2007,20(6):488-494
In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances. 相似文献
20.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献