脉泽分子云动力学结构的VLBI测量

利用VLBⅠMKⅢ记录系统, 在1665和1667MHz跃迁频率上, 观测活动恒星形成区NGC6334F的左右圆偏振羟基(OH)脉泽分子辐射;介绍了VLBIOH分子谱线观测过程, 给出了基本的观测结果, 并对结果作了简要地分析和讨论.      

太阳X-EUV成像望远镜的移动补偿系统

卫星帆板转动和自身颤动会导致太阳X射线-极紫外射线(X-EUV)成像望远镜的成像质量下降.用移动补偿系统控制相机的CCD驱动器,使势阱转移到相邻相的位置上,转移的方向正好与图像在传感器上移动方向一致,使得图像的每个光子在移动后仍然落入传感器的同一个势阱内,补偿由于帆板移动造成的图像偏移.CCD相移沿列的方向进行,而CCD的列平行于东西向.高精度太阳敏感器使用两轴直角坐标来定位太阳的位置.移动补偿系统只使用其中一个轴向数据,由于南北指向误差远远小于东西指向,因此不对南北指向补偿.该移动补偿系统利用高精度太阳敏感器构成半闭环控制系统,通过偏移CCD势阱来实现一个方向上的移动补偿.该方案可以在不增加成本的前提下,消除长时间曝光过程中的太阳的平移和帆板颤动对图像质量造成的影响,扩大动态观测范围.      

Hard X-ray footpoint motion and acceleration mechanism

An intense (X9.4/2B) flare, which occurred on 6 November 1997, was observed with the hard X-ray telescope on board Yohkoh. In the M2- (33 – 53 keV) and H-band (53 – 93 keV), This flare clearly show double footpoint sources during its impulsive phase. We have analyzed the locations and motions of these sources in detail. It is found that, at 11:53:06 UT, one of the footpoint sources in the M2-band moved to a new position earlier than the corresponding source in the H-band. The time-lag is about one second and the separation between the old and new positions is 5 arcsec. This happened between two major spikes in the time profile of hard X-ray intensity. This apparent motion might indicate that an epoch of energy release finished somewhere high in the corona and the next epoch started in another magnetic field system. This observation clearly shows that higher energy electrons precipitate into the footpoint region later. We try to interpret this particular phenomenon under the two assumptions, which are the direct precipitation model and the trap-and-precipitation model.     

Observational evidence for the binary model of X-ray bursters

Most, but not all, theoretical models of X-ray bursters require a binary system consisting of a mass donating star and a neutron star. The observational evidence in support of this model, however, is both indirect and meager. We have detected absorption dips in the X-ray spectrum of the Burster MXB 1916-05 with the IPC and the MPC on the Einstein Observatory which occur with a binary period of 2985 seconds. These dips are shown to be the result of a gas stream emanating from a companion star and hence this data represents the first direct evidence of the binary nature of X-ray bursters. Detailed models of the interaction of the gas stream with the accretion disk are presented. A 22nd mag. optical candidate for the system has been found.     

超静平台动力学建模与解耦控制

以超静平台在未来高精度航天器主动隔振和精确指向控制中的应用为基础,针对柔性铰形式超静平台的动力学特点以及超静平台基础和载荷扰动作用的影响,建立一般形式的超静平台动力学模型;进一步推导解耦力控制方法,将超静平台由高度耦合的多输入多输出系统变为单输入单输出线性时不变系统,以此消除各支杆之间的相互作用,极大地简化了控制器设计;在此基础上,进行数值仿真分析与验证.仿真结果表明:基于所建立的一般形式超静平台动力学模型,采用解耦力控制方法能够很好地实现超静平台的主动振动控制,并且方法简单易于工程实现.     

Design of tracking mount and controller for mobile satellite laser ranging system

In this study, we have proposed and implemented a design for the tracking mount and controller of the ARGO-M (Accurate Ranging system for Geodetic Observation - Mobile) which is a mobile satellite laser ranging (SLR) system developed by the Korea Astronomy and Space Science Institute (KASI) and Korea Institute of Machinery and Materials (KIMM). The tracking mount comprises a few core components such as bearings, driving motors and encoders. These components were selected as per the technical specifications for the tracking mount of the ARGO-M. A three-dimensional model of the tracking mount was designed. The frequency analysis of the model predicted that the first natural frequency of the designed tracking mount was high enough. The tracking controller is simulated using MATLAB/xPC Target to achieve the required pointing and tracking accuracy. In order to evaluate the system repeatability and tracking accuracy of the tracking mount, a prototype of the ARGO-M was fabricated, and repeatability tests were carried out using a laser interferometer. Tracking tests were conducted using the trajectories of low earth orbit (LEO) and high earth orbit (HEO) satellites. Based on the test results, it was confirmed that the prototype of the tracking mount and controller of the ARGO-M could achieve the required repeatability along with a tracking accuracy of less than 1 arcsec.     

高精度高动态星模拟器研究

给出了高精度高动态星模拟器系统组成和总体结构, 提出一种基于亚像素显示技术提高动态星模拟器星点位置显示精度从而减小星点几何中心与能量中心位置偏差的新方法. 针对动态星模拟器高动态性要求, 提出一种快速精确检索全天球导航星的新方法, 将已知SAO (Smithsonian Astrophysical Observatory) 星表进行分区, 计算当前姿态四元数并分析航天器视轴所在区域, 对于距离视轴较远区域停止搜索和匹配, 很大程度上缩小了导航星搜索范围, 进而缩短了全天球恒星遍历所需时间. 软件测试结果表明, 此快速检索法可使全天球导航星的选取速度提高近10倍.      

基于观测器的平台无陀螺姿态复合控制

针对超静卫星星体平台无陀螺、载荷敏感器与星体平台执行机构非共基准安装时整星存在姿态异位控制问题,提出了一种基于观测器估计星体平台姿态的复合控制方法。首先,建立星体平台/Stewart平台/载荷的动力学模型,并获得Stewart平台作动器关节空间的等效动力学模型。针对关节空间等效模型,设计super twisting观测器,以作动器平动位移为输入,以载荷和星体平台之间的相对姿态和角速度为输出,实现星体平台姿态和角速度估计。其次,以载荷测量姿态信息为输入,设计Stewart作动器的积分滑模控制律,实现载荷高精度指向控制。以观测器估计的星体平台姿态信息为输入,设计星体平台控制器实现星体平台的稳定控制。Lyapunov稳定性分析表明所设计的观测器和控制器能够保证闭环系统渐近稳定。数学仿真结果表明：在星体平台有陀螺时,载荷能够实现0.1″指向精度;在星体平台无陀螺时,采用观测器估计星体平台姿态并进行控制,载荷亦可实现0.1″指向精度。     

Stewart平台卫星动力学建模与姿态指向一体化控制

针对Stewart平台卫星大范围快速机动后的指向控制问题,提出了考虑翼板柔性的Stewart平台卫星动力学建模与姿态指向一体化控制方法。对考虑柔性翼板的Stewart平台卫星的动力学建模与主动控制进行了研究,采用力学基本原理和混合坐标法建立系统的刚柔耦合精确动力学模型,并提出一种同时考虑平台载荷指向与隔振的协同控制方案。数值仿真结果表明,所建立的动力学模型能够准确地描述系统的动力学行为,所提控制方案能够有效提高卫星平台的姿态指向精度。与未施加控制的情况相比,该方案能够将支撑杆的变形量减少到千分之一,从而保证了结构安全。此外,还分析了翼板柔性对Stewart平台卫星姿态控制的影响,结果表明翼板柔性对下平台姿态精度有较大影响,对上平台姿态精度影响较小。     

X-ray imaging techniques— modulation collimator and coded mask

Imaging over the hard X-ray energy band may be achieved by masking the flux with proper obstacles. The imaging modulation collimator has been developed and has been applied thus far, e.g., to produce hard X-ray pictures of the solar flare and to construct the X-ray image of the Crab Nebula up to the angular resolution of ～ 10 arcsec. Variations of the concept such as the Fourier Transform Telescope are discussed. Virtue of the modulation collimator is that high angular resolution may be achieved with a relatively simple detector system and that a wide field of view may be accomodated. Among several proposed coded masks, the techniques of Hadamard transform are discussed in some details. The coded mask is provided with a better total transmission, but its angular resolution is limited due to presently limited spatial resolution of the detector. Developments of the technique of the position sensitive detector are awaited for further improvements of the resolution.     

Design and construction of the ROSAT 5 arcsec mirror assembly

The ROSAT mission, which is currently being prepared in W.-Germany, will perform the first soft X-ray all-sky survey by means of a large imaging X-ray telescope. Detailed calculations under the cost, volume and mass constraint of the satellite being a Shuttle payload have led to a design of the imaging optics with optimized geometry. The mirror system is of the Wolter type I configuration and includes four nested shells with a maximum aperture of 835 mm and a focal length of 2400 mm. The on-axis angular resolution of the mirror assembly has been specified to 5 arcsec with a scattering level as low as 3% for single reflection at 1.5 keV photon energy. Construction and technology studies have been completed by now and manufacturing of the first mirror shell has begun.     

Non-LTE analysis of a new pulsating PG 1159-type central star detected in the ROSAT XRT all sky survey

We summarize the analysis of a new PG 1159 star, i.e., a hydrogen deficient pre-white dwarf detected in the ROSAT XRT all sky survey /1/. The X-ray source RX J2117.1+3412 is relatively faint (≈0.33 cnt s⁻¹) and was selected for optical identification on the basis of its extreme X-ray softness. With V = 13.2, the counterpart of the X-ray source is in the optical the second brightest member of the PG1159 class. CCD imagery reveals that the star is surrounded by an old highly excited planetary nebula of faint surface brightness. Optical line profiles of HeII, CIV, and OVI and the overall optical and ROSAT PSPC (0.1–2.4 keV) energy distributions are compared to predictions of NLTE model atmospheres. We find an excellent agreement between the atmospheric parameters derived from optical and soft X-ray data. The effective temperature of the star is extremely high (150,000 K). Abundances of He, C and O are found to be consistent with those derived in other PG1159 stars whereas the surface gravity is significantly smaller in RXJ2117.1+3412. New optical spectra presented here show the presence of ultra-high excitation lines of O VIII.     

挠性高稳定度卫星载荷扰动力矩补偿研究

有效载荷或星上运动部件相对卫星平台转动引入的扰动力矩严重影响卫星平台的姿态稳定度和指向精度.为满足卫星姿态高稳定度要求,采用正余弦细分驱动原理对帆板驱动机构(SADA)细分,并利用力矩补偿机构补偿有效载荷运动所引入的扰动力矩.此外,针对补偿机构自身存在的摩擦力矩设计补偿控制律,以改善其力矩输出性能.仿真算例表明设计方案有效.     

基于X射线脉冲星的深空探测自主导航方法

自主导航是实现深空探测任务的关键技术,基于X射线脉冲星的导航方法可靠、稳定、精度高,不受近地空间的限制,为深空自主导航提供了全新的思路。文章分析了X射线脉冲星导航的基本原理,提出了脉冲到达时间预报算法和整周模糊度求解方法,基于最小二乘理论研究了位置估计算法。仿真算例表明该方法在脉冲星方位误差为0.001弧秒、脉冲到达时间测量误差为1μs的情况下,140d飞行时间中定位精度优于10km,且对初始误差不敏感,可以满足深空探测的导航需要。     

轨道误差对星敏感器对地指向精度的影响分析

针对使用星敏感器进行对地指向精度问题,分析了影响卫星对地指向精度的主要因素,根据卫星轨道误差,推导了轨道根数误差对经度方向和纬度方向上的指向误差方程.分析了轨道根数对指向精度的影响规律.最后对轨道根数误差的影响进行了仿真,仿真结果与分析结果一致.     

一种便携式自动标校系统的开发与应用

该系统是基于计算机应用技术、星体标校方法、标准硬件接口及通用软件开发平台的便携式智能型检测系统 ,解决对野外分散站点上的光测设备进行检测、标校、监控和测控网通信联试等技术问题。着重阐述对外场经纬仪进行准确度检测和单项误差调整的自动化星体标校的原理和具体实现方法     

基于宽带宽测量的姿态确定方法

针对由飞轮等星上高速旋转部件所引起的高频姿态和指向抖动,提出一种基于磁流体动力学特性的角位移敏感器用于星上高精度宽带宽的微振动测量,以弥补常规姿态测量系统测量频带低,动态范围有限的缺点.介绍以扩展姿态确定带宽为基础的高精度姿态确定方法.给出了以陀螺、星敏及ADS测量信息为基础的宽带宽的姿态确定方法及系统的模型,采用了卡尔曼滤波来确定卫星姿态.仿真分析结果表明存在高频姿态抖动的情况下,宽带宽的姿态确定方法的估计精度优于传统的姿态确定方法,由此验证了宽带宽的姿态确定方法的有效性及精确性.     

高精度星相机光学系统像质评价及实现

摘要： 高精度星相机光学系统是实现高性能星相机的关键技术.从工程实际出发，梳理星相机光学系统像质评价的指标，重点论述星点质心位置指标分解、光学系统评价指标分解过程.分析认为星相机光学系统设计过程中需关注质心位置偏差和质心位置与理想像高的偏差、温度分析需兼顾均匀温升及梯度温度变化.给出一个继承于双高斯结构形式的设计实例，结合像差理论进行消热设计和畸变控制，分析不同温度条件下不同类别恒星的质心位置一致性.设计结果表明该光学系统可满足高精度星相机指标要求.     

X射线脉冲星4U 1538—52 的时间和能谱特性

本文处理分析了EXOSAT卫星对4U1538-524次中能观测资料,并结合其他观测结果对4U1538-52的时间和能谱特性作了分析和解释:中子星自转仍在减慢;能谱为幂律谱,Tenma卫星以后的观测未见Fe发射线;X射线dip现象可解释为一前景星对中子星的遮掩而形成;X射线爆发在不同的轨道位相出现,持续近1小时;在1keV附近似有一发射线。      

基于光电探测系统的地面车精确定位定向技术

针对地/地导弹发射车、指挥车、侦察车等陆地战车对车载定位/定向系统越来越高的要求,提出了一种利用光电探测系统测量3个已知标志点与地面车辆之间的角度信息来精确确定地面车辆的位置和航向的方法.仿真结果表明:只需依次对3个已知标志点进行1次光电测角,就可以精确确定地面车辆的位置和航向,并且东向和北向定位误差小于0.5m,方位误差小于20″(1σ).这种方法简单、快速,定位定向精度高,且能同时服务于同一场地的多辆地面车,具有重要的实用价值.