Joining of SiO2 ceramic and TC4 alloy by nanoparticles modified brazing filler metal

Nano-Al₂O₃ particles modified AgCuNi filler was adopted to braze the SiO₂ ceramic and TC4. The effects of filler size as well as the brazing temperature on the interfacial microstructure and mechanical property of the joints were investigated. Nanoscale filler reduced the phases dimension and promoted the homogeneous distribution of microstructure, obtaining a higher joint strength when compared to microscale filler. The increase of brazing temperature made the accelerating dissolution and diffusion of Ti, which promoted the increase of thickness of Ti₄O₇ + TiSi₂ layer adjacent to SiO₂ ceramic and diffusion layer zone nearby TC4 alloy. The hypoeutectic structure was produced in the brazing seam due to the high Ti content. The maximum shear strength of ∼40 MPa was obtained at 950 °C for 10 min.     

TC4-DT钛合金高温热变形行为研究

利用Gleeble-3500型热模拟实验机,研究了TC4-DT损伤容限型钛合金在温度850℃～1000℃、应变速率0.01～10s-1、变形程度为40%～70%条件下的热变形行为,分析了该合金的流变应力行为及微观组织演变规律,并建立了本构关系模型。研究结果表明,TC4-DT合金在950℃以下的较低温度变形时应力软化现象非常明显,变形机制和热变形激活能不同于950℃以上的较高温度变形机制;在950℃以上高温度变形时,低应变速率(如ε=0.01s-1)促进了动态再结晶行为的发生,而在较高的应变速率(如ε=10s-1)时,一般只发生动态回复现象,动态再结晶行为受抑制。     

Hot deformation behavior and strain compensation constitutive model of equiaxed fine grain diffusion-welded micro-duplex TC4 titanium alloy

In this work, two-stage diffusion bonding of micro-duplex TC4 titanium alloy was carried out to study the flow behavior and constitutive models of the bonding joint and the base metal after the same thermal cycling during the hot forming process. Microstructure and mechanical properties test were used to verify the good quality of the equiaxed fine grain diffusion-welded TC4 alloy. Quasi-static tensile experiment was carried out at temperatures ranging from 750–900 °C and strain rates of 0.0001–0.1 s⁻¹. The joint showed the weak dynamic recovery at strain rates of 0.01–0.1 s⁻¹ and temperatures of 750–850 °C. At strain rates of 0.0001–0.001 s⁻¹ and temperatures of 850–900 °C, the flow stress of joint presented steady-state characteristics. Different deformation conditions lead to the remarkable difference of dynamic softening performance between the joint and heat-treated base metal, but the flow stress in elastic and strain hardening stages exhibited similar behavior. The strain compensated Arrhenius-type constitutive models of TC4 joint and heat-treated base metal were developed respectively. The fifth-order polynomial functions between the material property correlation coefficients and strain were obtained. The models have shown good correlation, with correlation coefficient values of 0.984 and 0.99. The percentage average absolute relative error for the models were found to be 10% and 9.46%, respectively.     

B93铝合金热加工特性模拟研究

在Gleeble1500热模拟机上采用轴对称等温压缩实验,研究了B93铝合金在热加工中变形温度和应变速率对合金组织的影响,基于动态模型计算出B93铝合金加工图,分析合金热加工的流变失稳区并确定了合金热加工的最佳工艺参数。结果表明:变形速率和变形温度对B93铝合金的微观组织有影响;合金的峰值应力随变形温度的升高而降低,随变形速率的提高而增大;B93铝合金最佳的热加工制度为:变形温度420℃左右,应变速率0.001 s-1。     

挤压态喷射成形GH738合金热变形行为及组织研究

在温度950~1150℃、应变速率0.001~1 s–1及工程应变50%条件下,利用Gleeble-3500TM热模拟试验机对挤压态喷射成形GH738合金进行热压缩实验,研究合金的流变应力,建立合金热变形本构关系,利用EBSD分析合金组织演变。结果表明:合金流变应力随温度的升高和应变速率的减小而降低,在相同变形条件下,具有细晶组织特征的挤压态喷射成形GH738合金峰值流变应力低于粗晶组织的铸锻GH738合金;挤压态喷射成形GH738合金热变形激活能为651.08 kJ·mol–1,GH738合金的热变形激活能随着初始平均晶粒尺寸的减小而升高;形变温度的升高使挤压态喷射成形GH738合金初始被拉长的晶粒逐渐演变为等轴再结晶晶粒,在1000℃以上获得完全动态再结晶组织,再结晶组织随形变温度的进一步升高发生长大。     

Effect of Rhenium Addition on Isothermal Oxidation Behavior of Tribaloy T-800 Alloy

The effects of 4 wt% rhenium (Re) addition on isothermal oxidation behavior of Tribaloy T-800 alloy have been studied at 800 °C and 1 000 °C in air. At 800 °C, T-800 shows nonuniform oxidation between dendritic and eutectic areas. Re addition clearly promotes the nonuniform oxidation, leading to considerably higher mass gains than that of T-800 at this temperature. At 1 000 °C exposure, the thickness of scale on T-800 increases significantly, accompanied by severe scale spallation during cooling to room temperature. On the contrary, T-800Re shows a marked decrease of oxide growth rate compared to the linear one of T-800 at 1 000 °C. The scale adhesion is also improved with Re addition at this higher temperature. Therefore, the role of Re depends on the exposure temperature. Re addition gives high oxidation rate at 800 °C, however, the excellent oxidation resistance is obtained by the addition of Re at a higher temperature of 1 000 °C.     

TC11钛合金的组织及塑性与其断裂韧性及裂纹扩展速率的关系

研究了TCll合金的组织及拉伸塑性(ψ)与断裂韧性(K_(IC)及裂纹扩展(da/dN)的关系。指明:K_(IC)及da/dN与ψ的关系取决于合金的组织类型。对片状组织及等轴组织进行了具体分析。     

锻造温度对TC4合金组织与性能的影响

研究锻造加热温度对TC4合金组织与性能的影响规律。表明其均采用锻后水冷加强化热处理相同条件下,TC4合金采用高温锻造(相变点以下10℃至相变点以上5℃),可以获得细密交错的网状α+β组织,或其间伴有少量等轴α相的双态组织,从而可得到高强度与高塑性的性能。本文还讨论了上述工艺使TC4合金有效强化的机理。     

激光冲击强化对钛合金高温微动疲劳寿命的影响

为了解高温工作环境下激光冲击强化工艺(LSP)对钛合金材料微动疲劳寿命的影响,开展了强化前后TC11钛合金在室温、300°C和500°C下的微动疲劳试验并测试了试验件表层的残余应力及硬度。结果表明:随着温度的升高,激光冲击强化对TC11钛合金微动疲劳寿命的提高倍数逐渐减小。在轴向载荷为400MPa,法向载荷为65.5MPa时,经激光冲击强化后TC11钛合金试验件在室温、300°C和500°C下的微动疲劳寿命分别为强化前的5.5倍、3.5倍和1.7倍;强化后试验件表层的残余应力会在高温下发生松弛,且松弛程度会随温度的升高而增大,这是激光冲击强化效果随温度升高而逐渐弱化的主要原因。     

TC11合金热变形特性及变形参数对组织的影响

通过热模拟压缩试验,分析了TC11合金的高温变形特性及不同变形参数下的组织演化规律,用非线性回归方法建立了TC11合金Kumar型材料的本构关系,得出了TC11合金的高温流变曲线基本呈流变软化特征的结论;最后应用MSC,Autoforge软件对TC11合金某型号涡轮盘的等温锻造工艺进行了模拟式工艺设计,验证了TC11合金材料本构关系的工程适用性.     

不同热处理工艺下激光增材制造TC4钛合金组织与性能研究进展

由于激光增材制造(Laser Additive Manufacturing,LAM)TC4钛合金加工成形过程的特殊性,导致该合金在力学性能上存在明显的各向异性,同时韧性、疲劳性能不能很好地满足使用要求。从材料组织与力学性能之间的关系出发,介绍了不同热处理工艺对激光增材制造TC4钛合金组织与力学性能的影响,指出了当前激光增材制造TC4钛合金热处理研究中存在的问题,并为后续激光增材制造TC4钛合金的热处理研究提供思路与方向。     

TC11合金燃烧特性初步研究

钛火严重威胁航空发动机用钛安全,开展钛合金燃烧特性研究是发动机合理用钛及采取有效防范措施的基础。通过液滴引燃试验法初步研究了TC11合金的燃烧特性,分析了燃烧的过程特征、试片温度与氧气含量(分压)对启燃的影响及燃烧表面的微观组织。结果表明:在压缩空气/氧气作用下,TA1液滴发生燃烧并将TC11合金试片引燃,燃烧过程中反应剧烈,喷射出大量火花;随着TC11合金试片温度的提高,引燃所需的临界氧气分压逐渐降低;TC11合金试片的烧损表面形成了氧化层,从表面到内部呈现出疏松区、致密区和燃烧影响区三种典型的组织区。     

飞秒脉冲激光诱导TC4微结构表面抑冰特性实验

飞机发动机进气道前缘唇口积冰将会严重威胁航空安全,仿生研究表明具有微纳结构的疏水表面可以起到良好的抑冰效果。针对飞机唇口材料TC4,采用飞秒脉冲激光诱导制备TC4微结构表面,利用三维形貌仪和扫描电镜对TC4合金表面三维形貌和微纳结构进行观测,应用接触角测量仪分析表面浸润改性,依托结冰特性实验系统测试微结构表面抑冰抑霜性能,并分析飞秒脉冲激光加工工艺参数对表面微观结构和抑霜特性的影响机制。研究结果表明：随着激光扫描速度的增大,TC4合金表面形成的拱形沟壑深度增加,沟壑上方出现干涉条纹以及圆形凸起且微纳凸起的尺寸随扫描速度的增大而增大,接触角先减小后增大再减小;加工后表面液滴冻结时间比未加工表面延迟30 s;扫描速度2 000 mm/s时的液滴冻结时间最长,霜层质量最小,高度最低。飞秒激光加工TC4合金表面形成的微纳结构以及表面吸附的有机物能够改变表面接触角;粗糙度和表面形貌能够影响表面结冰时间和结霜量。     

TC6钛合金超塑性变形

对TC6钛合金在800~900℃温度区间内,分别进行应变速率为0.0001~0.1 s-1的恒应变速率法拉伸实验和最大m值法超塑性拉伸实验,获得拉伸过程应力-应变曲线,并采用金相显微镜对拉伸后断口附近显微组织进行分析。结果表明：TC6合金表现出良好的超塑性性能,随着应变速率或温度的升高,伸长率先增大后减小,恒应变速率拉伸时,在温度850℃、应变速率0.001 s-1条件下伸长率可达到993%;在同一变形温度下最大m值法拉伸能获得比恒应变速率法更好的超塑性,850℃时伸长率达到1353%;TC6合金在超塑性变形过程中发生了明显的动态再结晶,并随着应变速率和温度的升高动态再结晶行为增强。     

Ti2AlNb合金双层辉光等离子表面渗钼的扩散行为研究

Ti2AlNb合金(O相)具有高的比强度、断裂韧性以及优良的抗蠕变性能,因而在航空制造中成为一种颇具吸引力的高温结构材料.但是,较差的耐磨性是其主要的缺陷并限制其实际应用.为解决这一问题,对Ti2AlNb合金进行双层辉光等离子表面渗Mo.探讨主要工艺参数对Mo的扩散行为的影响.采用扫描电镜(SEM)、X射线衍射(XRD)和辉光放电光谱仪(GDS)分析表面合金化层的成分分布和微观结构.测定从表面到中心的显微硬度变化曲线.结果表明温度与时间均对扩散过程具有显著的影响.最后通过回归分析计算出在优化的工艺温度980℃下的扩散系数.     

Effects of RRA Treatments on Microstructures and Properties of a New High-strength Aluminum-Lithium Alloy-2A97

A new high strength 2A97 Al-Cu-Li-X alloy was subjected to triple-aging of retrogression and re-aging treatments (RRA). Transmission electron microscopy (TEM), differential scanning calorimetry (DSC), and tensile tests were used to investigate the effects of RRA treatment on the microstructures and properties. DSC test reveals the reversion temperature range of the strengthening δ' (Al3Li)phase. The results show that the microstructure consists of δ' (Al3Li) phase, T1 (Al2CuLi) phase and θ"/θ'(Al2Cu) phase for 2A97 alloy treated by a triple-aging ora retrogression and re-aging treatment in the following order: (1) at 165 ℃×30 min, (2) at 220 ℃ or 240 ℃×15 min, (3) at 165 ℃×24 h. The plastic deformation, incorporated into the treatment after secondary high temperature aging, promotes the T1 precipitation during final re-aging. The tensile properties of the alloy treated by the retrogression and re-aging treatment reach the peak level of alloy single-aged at 165 ℃ in T6 temper.     

超声喷丸与传统喷丸对TC4 钛合金残余应力影响的仿真分析

为了预测喷丸TC4钛合金试件的残余压应力层深度及值的分布和冲击面凹坑的直径、深度特征曲线及表面形貌的变化,采用ABAQUS/Explicit软件建立2个3D模型。通过超声喷丸与传统喷丸2种工艺过程数值仿真对比了表面残余应力场差异,分析了TC4钛合金弹丸直径、速度和冲击次数等喷丸参数对残余应力分布的影响。结果表明:当动能相同时,2种强化过程表面所产生的残余压应力是可比较的,超声喷丸模型亚表层残余应力深度为0.16 mm,约为传统喷丸模型深度的2倍;传统喷丸产生的残余压应力最大值约-800 MPa,约为超声喷丸的1.6倍。与传统喷丸相比,超声喷丸具有较低的表面粗糙度以及较深的残余压应力层。残余压应力层深度与弹丸直径呈正相关,但过大的弹丸尺寸会引起薄壁件另一侧残余拉应力区域的增大。     

定向凝固钴基高温合金DZ40M的热处理研究

研究了热处理对新研制的定向凝固钴基高温合金DZ40M组织和性能的影响。结果表明 :12 80℃ / 4h固溶处理可完全溶解DZ40M合金中初生碳化物M7C3 和MC ,合金成为单相固溶体。95 0℃和 10 5 0℃时效处理可使DZ40M合金发生硬化 ,以 95 0℃时效硬化效果更为明显 ,相应的峰时效制度为 95 0℃ / 12h和 10 5 0℃ / 2 4h。时效处理引起M2 3 C6沉淀析出。 95 0℃ / 12h时效显著提高DZ40M合金室温强度和高温持久寿命 ,同时也减少了合金塑性 ,但合金仍保持一定的塑性。 10 5 0℃ / 2 4h虽然能增加室温拉伸性能 ,但削弱了高温持久性能     

TC4合金的新型本构关系

通过热态模拟试验 ,系统地研究了主要锻造热力参数 (变形速度、变形温度、变形程度 )与 TC4合金流动应力、微观组织之间的数值关系 ,采用数理统计原理 ,科学地分析并回归出了能综合反映锻造热力参数和微观组织演化过程对材料成形性能影响的本构方程 ,定性地探讨了各热力参数对 TC4合金组织和性能的影响规律 ,为TC4合金锻造过程的数值模拟和锻造热力参数的合理制订与控制提供了基础。     

粉末冶金Ti-6Al-4V 的组织及形成机理

利用热等静压(HIP)技术及旋转电极粉,采用预合金粉工艺制备了全致密的粉末冶金Ti-6Al-4V合金,用光学显微镜对其金相组织进行了观察,分析其形成机理,并对粉末冶金Ti-6Al-4V合金的室温拉伸性能、弹性模量、冲击性能及断裂韧性进行了研究.结果表明:粉末冶金Ti-6Al-4V金相组织主要由条片α相+相间β相组成,有细小的等轴α相分布在晶粒界面处,包裹着条片α相,这种独特的组织状态是由制备工艺决定的,具有良好的综合性能.