共查询到20条相似文献,搜索用时 46 毫秒
1.
为研究不同导风装置对双塔干扰下大型冷却塔表面平均和脉动风荷载分布特性的影响,基于风洞试验对比研究了三种有导风装置和无导风装置的大型冷却塔表面风压随机分布特性,其中包括平均风压、脉动风压、峰值因子、极值风压以及干扰因子等气动参数。研究结果表明:增设导风装置后塔筒背风面负压区气流紊乱,平均风压呈现明显波动;不同导风装置对塔筒下部断面测点峰值因子影响显著,数值主要分布在3.2~3.6之间;极值风压分布规律类似于冷却塔模态的正反对称特点,外部进水槽对喉部侧风面极值风压增大了近0.5;90°风向角为双塔布置的最不利工况,夹道效应导致塔筒侧风面平均风压、脉动风压与极值风压变化显著,此时带外部进水槽的冷却塔中上部断面层阻力系数的干扰因子达到最大值。 相似文献
2.
超大型双曲冷却塔风荷载特性风洞试验研究 总被引:7,自引:1,他引:7
结合韩城第二电厂冷却塔风洞试验,在模拟大气边界层和周边地貌的情况下,研究了不同风向角下,超大型冷却塔风荷载特性及高大地面建筑群的影响。给出了风荷载高度变化系数、风压分布特性及其三维效应区域、地面附着物影响和风荷载体形系数,与《建筑结构荷载规范》中B类地貌上述参数有较明显差异,对双曲冷却塔、特别是超大型双曲冷却塔工程结构设计,有重要的参考价值。 相似文献
3.
为识别大跨度桥梁主梁断面在龙卷风作用下的风荷载特性及其主要影响实验参数,在龙卷风风场特性模拟的基础上,基于龙卷风模拟装置和刚体模型测压实验方法,对流线型扁平钢箱主梁表面风压分布、断面三分力系数等风荷载特性进行了识别,并讨论了涡流比、高宽比等龙卷风相似参数对风荷载识别结果的影响。结果表明,桥梁主梁在模拟龙卷风作用下的风荷载特性与常规边界层风洞实验结果明显不同。高宽比对风荷载特性的影响程度远大于其对风场特性的影响。不同涡流比下,高宽比对风荷载特性的影响程度不同。高宽比和涡流比是影响桥梁主梁龙卷风荷载的关键相似参数。风荷载模拟结果及其关键相似参数的影响规律将为桥梁抗龙卷风设计提供基础气动参数数据。 相似文献
4.
5.
冷却塔群塔为常见的群体建筑物组合形式,存在复杂的塔群干扰效应.传统的群塔干扰效应研究通常面向塔筒等效静风荷载,忽略了群塔组合对于脉动风压分布模式干扰效应的量化研究.为了研究群塔组合条件下脉动风压的干扰分布模式,选取具备多种气动干扰特点的八塔组合矩形布置方案为研究对象,对群塔进行刚性模型同步测压风洞试验,获取了不同风向角条件下塔筒表面的脉动风压分布.在"迎风来流"、"侧风来流"和"背风来流"等三种典型来流模式下,结合风向角的变化将脉动风压分布形式总结为"V"型、"M"型、半"V"型+半"M"型三类,探讨了干扰影响脉动风压分布的机理,发现可将脉动荷载的干扰效应分为"弱干扰"、"非对称强干扰"和"对称强干扰"三种类别;在量化表达脉动风压干扰分布方面提出了脉动风压分布的九项式拟合公式,并按照三类分布模式给出了脉动风压的推荐表达式. 相似文献
6.
7.
北京国际金融大厦风荷载风洞实验研究 总被引:2,自引:0,他引:2
具有独特外形,荣获1994-1995年度首都十佳建筑设计方案第一名的北京国际金融大大厦风荷载风洞实验研究结果表明,由于该建筑独特的门廊型南北错落 表面风荷载随风向角变化很大,这对今后同一类型的建筑设计从风荷载角度来考虑具有指导意义。笔者还结合北京地区特定的气象条件,参考国外文献,提出了较为合理的可靠的玻璃幕墙风荷载设计值。 相似文献
8.
北京某国际金融大厦风荷载与火灾流场的数值模拟 总被引:1,自引:0,他引:1
对北京金融大厦风荷载进行了计算机数值模拟,给出院 风洞中模型表面风荷载随风向角变化的一般规律并和文献[1]的实验结果进行了比较。给出了实验模型周围的流动图画和气流参数的分布规律,另外,分析了构成该建筑的四栋相邻近的建筑之间发生火灾后的流动特性,提出了比其它建筑结构更易于扩大火灾发展的原因和补救措施。 相似文献
9.
10.
风驱雨CFD模拟及平均雨荷载计算方法研究 总被引:1,自引:0,他引:1
基于谐波叠加法,用Kaimal谱生成空旷场地的脉动风速时程,将脉动风速时程作为流场CFD模拟的速度入口。采用分离涡模型模拟脉动风场并用离散相模拟雨滴颗粒,通过风雨耦合的CFD模型,获得雨滴落在输电塔各高度处的雨滴速度以及时间,并依据冲量定理和冲量等效原则,提出了任一时距的平均雨荷载计算方法。以176m高的输电塔为例,计算出作用在输电塔上以0.25s为时距的平均雨荷载。研究了水平风速和降雨强度对平均雨荷载的影响,结果显示:水平平均雨荷载随水平风速和降雨强度的增加而增加,但水平平均雨荷载与风荷载的比值沿高度增加而递减;尽管单粒雨滴荷载较大,但作用时间只有大约1×10-5s,依据冲量等效原则计算得出在一定时距内的平均雨荷载较小;对于本文算例,平均雨荷载与平均风荷载的比值不超过2.6%。 相似文献
11.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
12.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
13.
14.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
15.
16.
航天器返回地球的气动特性综述 总被引:4,自引:0,他引:4
航天器返回地球的飞行过程中,气动特性是实现将宇宙飞行速度减到落地前速度、保证再入飞行得到有效控制以及再入防热安全可靠的关键因素。针对简单旋成体气动外形、半弹道式再入控制、烧蚀防热类返回航天器,综述了返回地球过程中变化的空气流域特性、航天器周围的气体绕流环境、空气与航天器作用产生的动力学与热效应等。系统地给出了该类航天器的再入气动特性参数与飞行性能的共性规律,包括:气动阻力与再入减速、气动升力与再入轨迹控制、配平攻角与飞行稳定性、气动加热与防热,以及再入过程中不同气动特性航天器、气象条件变化等对再入飞行性能的影响规律。为航天器开展返回飞行过程的跨流域气动性能工程研制提供设计参考。 相似文献
17.
Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis 总被引:2,自引:0,他引:2
GAO Hong-liang ZHANG Hui WANG Shu-juan 《中国航空学报》2007,20(1):75-80
Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved. 相似文献
18.
19.
Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters 总被引:1,自引:0,他引:1
ZHOU Hong-guo WEI Xiu-ying MAO Chang-hui XIONG Yu-hua QIN Guang-rong 《中国航空学报》2007,20(2):172-176
The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃). 相似文献
20.
YANG Fen ZHANG Xue-jun TIAN Fang WU Xu GAN Fu-xing 《中国航空学报》2007,20(2):181-186
Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration. 相似文献