Error Analysis of the Optimal Antenna Array Processors

The optimal weights of an antenna array processor, which maximizes the output signal-to-noise ratio (SNR) in the absence of errors, are computed using the noise-alone matrix inverse (NAMI) and the steering vector in the look direction or the signal-plus-noise matrix inverse (SPNMI) and the steering vector. In practice the estimated steering vector as well as the estimated optimal weights are corrupted by random errors. This paper has analyzed the effects of these errors on the performance of the NAMI processor and the SPNMI processor by deriving analytic expressions for the output signal power, output noise power, output SNR, and the array gain as a function of the error variance. The treatment is for a general array configuration and no assumption about a particular array geometry is made.     

Analysis of a Signal Processor for an Antenna Array

A signal processor that provides ratio-squared predetection combining, has been investigated for application in an adaptive antenna array. The analysis and experimental data presented here pertain to the signal processing gain when the antenna array is illuminated by a coherent signal source and a partially coherent noise source. For a noise source which is coherent, the processing gain depends on relative strength of the signal and noise, relative directions of arrival, and the usual "array factor." The array exhibits capturing effects much as in an FM receiver. The effective antenna pattern is a superposition of two beams of different magnitudes, one directed to the signal source and the other to the noise source. When the noise is partially coherent, the behavior of the signal processor is quite complex. Analytical prediction and experimental simulation measurement on a four-channel system indicate that the partially coherent noise may be regarded as the source of an incoherent noise component plus a coherent noise component with the magnitude of the latter determined by the coherence coefficient for the noise source.     

星载DBF接收天线误差校正算法

 提出了一种改进的基于子空间的星载数字波束形成（DBF）接收天线的误差校正方法。根据阵列互耦效应主要取决于阵元间的几何距离这一特点,利用阵元空间排布的对称性简化了天线的互耦模型,将天线的互耦效应及射频(RF)通道失配统一为通道间的幅相不一致。通过在基带注入特定的阵内相位差降低了子空间算法的计算复杂度。在建立7单元正六边形平面阵仿真模型的基础上,分析不同信噪比(SNR)环境下校正算法的性能,经比较得出可以通过提高发射信号功率改善误差估计的精度,验证了算法的有效性。仿真分析结果表明该算法在卫星通信系统中有一定的工程应用价值。     

Multiplier Offset Voltages in Adaptive Arrays

The effects of multiplier offset voltages in adaptive arrays are examined. Multiplier offset voltages arise when active circuits are used to implement the error-by-signal multipliers required in an array based on the LMS algorithm. These offset voltages are known from experimental work to have a strong effect on array performance. It is first shown how multiplier offset voltages may be included in the differential equations for the array weights. Then their effect on weight behavior is studied. It is found that the offset voltages affect the final values of the weights, but not the time constants. Furthermore, the effect they have is influenced by the amount of element noise in the array. An adequate amount of noise is necessary to minimize weight errors due to offset voltages. An example is treated to show the effect of offset voltages on the final array weights and the output signal-to-noise ratio (SNR). With offset voltages present, it is found that there is a maximum SNR that can be obtained from the array. A specific input SNR is required to obtain this maximum output SNR. Finally, it is shown that a finite operating range for the weights places a further restriction on the acceptable values of offset voltages and noise.     

Postfiltering in Digital Beamformers

Assuming a sinusoidal signal superimposed on a narrow-band Gaussian noise as the input to a receiving array, the output power and signal-to-noise ratio of a digital beamformer with postfiltering were formulated so that subsequent calculations could be made without an analysis in the frequency domain. The formulation utilized the quantizer functions previously given by the author and certain spectral power distribution factors originally attributed to Davenport but more rigorously derived and discussed in the present work. A numerical study based on this formulation for a DIMUS array in a correlated noise field reveals that except for certain rare circumstances, postfiltering generally improves the output SNR or array gain. It is demonstrated that the amount of postfiltering gain not only varies with array input SNR but also depends strongly upon the spacing-to-wavelength ratio, and its meaningful interpretation can only be made in conjunction with both the clipping and noise correlation losses. In particular, balancing postfiltering gain against the two losses suggests that receiving arrays with element spacings smaller than one-half of the operating wavelength may be used to the advantage of system design under certain conditions.     

Detection of weak, subpixel targets using mesh-connected cellularautomata

Effective use of military cellular automata such as military data array processor (MilDAP) and geometric arithmetic parallel processor (GAPP), in weak, subpixel target detection is shown to be possible by using new signal processing regimes based on binary ranking filter theory. By using binary ranking filters, the MilDAP can furnish 6 dB of processing gain against white Gaussian noise while monitoring from one to four million potential target tracks at 10-40 frames/s. GAPP is shown to be capable of monitoring 3.7 million tracks over 216×384 detectors at 14000 frames/s and, in a time sharing mode, 15 million tracks over 432×768 detectors at 24 frames/s. The special case of threatening targets is discussed, as well as alternate cellular architectures which use multidimensional binary ranking filters in multidimensional coordinate systems     

Optimum Active Array Processing Structure and Space-Time Factorability

An active array processor is concerned with the problem of detecting a signal echo, reflected from a target, in the presence of reverberation (clutter). The processor can also be used to estimate target range and bearing. It is a priori not evident whether the optimum (likelihood ratio) detector can be factored into spatial and temporal operations, thus resulting in a simpler processor implementation. This paper studies this problem for a linear continuous array in a reverberation-limited environment. Conditions on signal, reverberation, and array parameters are derived under which the optimum detector is factorable. The validity of using factorability as a criterion of signal design is briefly examined. Finally, the relationship between space-time factorability and range-bearing estimates is pointed out.     

天线组阵中SUMPLE算法的合成相位漂移补偿

针对SUMPLE算法在低信噪比时存在的相位漂移问题,在分析权值估计误差引起的合成信号相位漂移现象的基础上,提出一种以固定时刻合成权值作为参考的补偿算法。该算法以收敛后某个固定时刻的合成权值作为参考,其他时刻的相位补偿值通过与该参考权值进行相关计算得到。从理论上分析了该算法的可行性,并进行仿真验证。理论分析与仿真结果表明,所给出的相位补偿方法能有效地消除合成信号的相位漂移现象,补偿后的合成信号相位中心稳定。     

Time jitter analysis for quadrature sampling

Time jitter in the quadrature sampling processes is modeled and the performance of an adaptive cancellation system in the presence of such time jitter is analyzed. It is shown that the decorrelation due to time jitter depends on the magnitude of the jitter, the sampling scheme used, the bandwidth of the signal and the intermediate frequency (IF) preceding the analog-to-digital (A/D) conversion stages. The performance of a sidelobe cancellation system in the presence of time jitter, for several sampling approaches, is evaluated numerically as well as simulated. The results show that the direct quadrature sampling scheme with a lower IF provides superior performance for an adaptive cancellation system     

常规闭口风洞相阵列气动声学试验

传统气动声学研究观点认为,精确的声学测量要求风洞背景噪声和洞壁反射足够低,传声器测量结果有足够高的信噪比,这是大多数风洞无法达到的要求。近些年,基于声纳和雷达技术发展起来的麦克风相阵列技术可以通过增加阵列的传声器数目从而大幅提高声学测量的信噪比,具有噪声源研究和定位能力,并被成功地应用于非声学固壁风洞噪声源测量和噪声物理机制研究。作者基于相阵列波束生成频域算法研制出常规闭口风洞相阵列系统及相关技术,在FD-09风洞尝试进行了相阵列校准试验和某民机噪声测量试验。结果表明：相阵列技术能够准确捕捉到真实的校准声源,并从技术上验证了相阵列系统在常规闭口风洞测量气动噪声是有效的。     

新型Σ-Δ多通道动态测试分析系统研究与实现

 动态测试与分析系统需要动态范围（DRN）大、信噪比（SNR）高,传统方法实现复杂且成本高。本文分析了Σ-Δ调制的动态特性,提出基于Σ-Δ ADC(模-数转换器)ADS1271,Σ-Δ DAC（数-模转换器）AIC23及浮点数字信号处理器（DSP）芯片TMS320C6713的新型高精度动态测试与分析系统,实现了多通道实时动态测试与分析,系统具有24位采集精度,8通道可级联基本模块,实时频率细化FFT（Zoom-FFT）、功率谱密度（PSD）等分析功能, 正弦、瞬态扫频、随机和冲击响应谱等信号源功能以及高速USB2.0数据传输功能。系统用于振动、冲击、噪声工程等测试与分析系统,可取代国外最新产品。     

确定相干机器多噪声源位置的方法研究

提出利用均匀线阵接收的数据构造一种矩阵进行奇异值（SVD）分解,以实现对相干噪声源的方位估计。利用这种方法,通过改变阵列中心位置便可确定机器多噪声源位置。计算机模拟和声学实验证实了这种方法的可行性。     

Radiometric detection of spread-spectrum signals in noise ofuncertain power

The standard analysis of the radiometric detectability of a spread-spectrum signal assumes a background of stationary, white Gaussian noise whose power spectral density can be measured very accurately. This assumption yields a fairly high probability of interception, even for signals of short duration. By explicitly considering the effect of uncertain knowledge of the noise power density, it is demonstrated that detection of these signals by a wideband radiometer can be considerably more difficult in practice than is indicated by the standard result. Worst-case performance bounds are provided as a function of input signal-to-noise ratio (SNR), time-bandwidth (TW) product and peak-to-peak noise uncertainty. The results are illustrated graphically for a number of situations of interest. It is also shown that asymptotically, as the TW product becomes large, the SNR required for detection becomes a function of noise uncertainty only and is independent of the detection parameters and the observation interval     

DOA estimation using one-bit quantized measurements

The effects 1-bit quantization of the input samples has on the direction-of-arrival (DOA) estimation accuracy are considered. The signal model assumes a single stochastic Gaussian point source that is embedded in white Gaussian noise (WGN). The inherent limitations governed by the extreme clipping of the input data are analyzed using the Cramer-Rao bound (CRB) that is derived for a two-sensor array. In addition, several estimators for the I-bit estimation are discussed. Numerical and analytical analyses of the estimation error reveal weak dependency on signal-to-noise ratio (SNR) with singular behavior of the estimation error in certain DOA angles.     

随机共振锁频环路影响因素

针对随机共振锁频环路影响因素不够明朗的问题，在对随机共振锁频环路仿真验证的基础上，重点对信噪比、采样频率和系统参数对环路性能的影响进行了探究。首先，阐述了随机共振锁频环路基本原理，搭建了随机共振锁频环路模拟仿真平台。其次，通过设定不同的信噪比、采样频率和系统参数条件，观察随机共振锁频环路性能变化。最后，总结归纳出各条件对随机共振锁频环路的影响。仿真结果表明，信噪比越低，随机共振锁频环路对信号跟踪性能越差，且最低能够处理信噪比为Eb/N0=1dB的信号。采样频率在高于信号频率50倍时，提高采样频率虽可提高计算精度，但对环路跟踪性能改善作用不大。系统参数是决定随机共振效应能否发生及影响共振效果的关键因素，其表现为一个可供选择的数值区间。     

使用电场传感器阵列的水下运动目标检测与参数估计

研究了基于电场传感器阵列的水下运动目标检测与参数估计方法。在背景噪声为高斯白噪声和目标作匀速直线运动的假设下,利用电场传感器阵列获取的船舶水下准静态电场空时特征,通过广义似然比检测和随机搜索寻优算法,可实现对海水中运动船舶的目标检测和参数估计。仿真试验结果表明:在信噪比大于0 dB时能够取得较好的估计精度;在信噪比低至10 dB时仍能有效检测目标。     

高信噪比、高分辨宽测绘带成像

针对传统高分辨和宽测绘带以及高信噪比和宽测绘带之间的矛盾,提出一种基于脉内扫描面阵合成孔径雷达(SAR)系统的二维空域联合处理算法实现高信噪比、高分辨宽测绘带成像。文中首先建立脉内扫描面阵SAR系统模型,该系统采用低脉冲重复频率(PRF)获得宽测绘带信息,同时利用脉内扫描方式获得高信噪比的回波信号。对于低PRF采样宽多普勒谱(对应方位高分辨)引起的多普勒模糊以及脉内扫描引起的距离模糊,提出一种二维空域联合处理算法解距离和多普勒模糊,并且详细地分析了地形高度变化对解模糊算法的影响。最后,通过仿真实验验证了本文算法的有效性。     

基于提前停止判决的编码软信息辅助载波同步

 针对目前编码辅助载波同步算法中复杂度较高、延时大的问题,提出了引入辅助停止判决机制的编码辅助载波同步算法。在现有的编码辅助载波同步结构基础上,该算法能对环路信噪比(SNR)进行实时判定,在环路SNR满足限定条件后提前停止编码辅助载波同步迭代,而不影响译码性能。采用新的相位估计方式估计含相位噪声的载波相位,提升了该条件下的环路信噪比。仿真采用码率为1/2的低密度奇偶校验(LDPC)码作为编码方式,结果表明:在误码率为10^-5时,该算法减少了约50%的编码辅助载波同步迭代次数;在含相位噪声的信号条件下,与理想解调译码相比,性能损失不超过0.15 dB。     

Median cascaded canceller for robust adaptive array processing

A median cascaded canceller (MCC) is introduced as a robust multichannel adaptive array processor. Compared with sample matrix inversion (SMI) methods, it is shown to significantly reduce the deleterious effects of impulsive noise spikes (outliers) on convergence performance of metrics; such as (normalized) output residue power and signal to interference-plus-noise ratio (SINR). For the case of no outliers, the MCC convergence performance remains commensurate with SMI methods for several practical interference scenarios. It is shown that the MCC offers natural protection against desired signal (target) cancellation when weight training data contains strong target components. In addition, results are shown for a high-fidelity, simulated, barrage jamming and nonhomogenous clutter environment. Here the MCC is used in a space-time adaptive processing (STAP) configuration for airborne radar interference mitigation. Results indicate the MCC produces a marked SINR performance improvement over SMI methods.     

GPS多径信号的自适应滤波估计方法

 研究全球定位系统(GPS)多径信号估计的问题。通过分析自适应滤波器的原理,建立了数字中频信号处理的数学模型,提出一种用自适应滤波实现GPS多径幅度、码相位和载波相位估计的方法。该方法采用不同延迟的伪随机序列对信号进行解扩、解调和累加,得到了作为期望信号的系列自适应滤波相关值。对该方法与其他3种方法进行了理论上的分析比较,得出本方法具有信噪比高、自适应滤波性能好、带有码相位信息和不存在载波模糊度问题等优点。根据各种滤波器算法的特点和本应用的需求,给出了选用递归最小二乘算法实现的方法。通过计算机仿真,验证了提出的方法能够在14 dB的信噪比下,以1个采样间隔的时间延迟分辨率和0.005周的载波相位估计精度估计出GPS L1的多径信号。