A fixed frequency LCL-Type series resonant converter

A fixed frequency LCL-type series resonant converter (SRC) which uses an inductive output filter is proposed. Steady-state analysis of the converter is presented using complex ac circuit analysis. Based on the analysis, a simple design procedure is given. Detailed space integrated control experiment (SPICE) simulation results are presented to evaluate the performance of the designed converter under varying load and supply voltage conditions. Also, detailed experimental results obtained from a metal-oxide-semiconductor field-effect transistor (MOSFET) based 500 W converter are presented to verify the analysis and SPICE simulation results. The results obtained from the analysis, SPICE simulation and the experimental converter are compared. The proposed converter requires a narrow variation in pulsewidth while maintaining lagging power factor mode of operation for a very wide variation in the load as well as supply voltage     

Analysis and design of a three-phase LCC-type resonant converter

A three-phase dc-to-dc LCC-type resonant converter with high-frequency transformer isolation is proposed. The operation and a simple analysis of the converter are presented. Design curves are obtained and a design example is given. SPICE simulation and experimental results are presented to verify the performance of the proposed converter for varying load conditions. The converter proposed has several advantages, e.g., operation in lagging PF mode for the entire load range, requires a narrow variation required in switching frequency, reduced component size and stresses, etc     

Analysis and design of series-parallel resonant power supply

A modified series-parallel high-frequency resonant DC/DC converter configuration is proposed. A simplified steady-state analysis of the converter, including the effect of a high-frequency transformer using complex circuit analysis, is presented. Based on the analysis, a simple design procedure is given. The effect of magnetizing inductances of the high-frequency transformer on the performance of the converter is discussed. Detailed experimental results obtained from a MOSFET (metal-oxide-semiconductor field-effect-transistor)-based 1-kW converter are presented to verify the analysis. The converter presented has almost constant efficiency from full load to quarter load, and the converter has load short circuit capability     

High power factor operation of DCM series-parallel resonantconverter

This work presents the operating principle, analysis, design, simulation, and experimental results for a high frequency (HF) transformer isolated single stage ac-to-dc series-parallel resonant converter (SPRC) operating on the utility line, in discontinuous current mode (DCM). The equivalent circuit models and the state space analysis of the SPRC in DCM are presented. PROMATLAB software is used to solve the equations and to obtain important design parameters. SPICE3 simulation and experimental results obtained from a 150 W prototype are presented to verify the analysis. High power factor operation (>0.99) with low harmonic distortion (<18%) have been achieved for the entire load range even without active control, in addition to eliminating switching losses     

Three-phase single-stage ac/dc boost integrated series resonant converter

A new ac/dc 3-/spl phi/ single-stage converter is proposed integrating a 3-/spl phi/ discontinuous current mode (DCM) boost with a dc/dc fixed frequency series resonant converter (SRC). This converter has the following features: natural power factor correction, soft switching, high-frequency (HF) transformer isolation with the series resonant tank operating in above resonance mode, etc. A new complementary gating control scheme is used for simultaneous control of boost converter and the SRC. Modes of operation are presented and analyzed. Based on the analysis, design curves are obtained. An optimum design is given and a design example is presented. Results obtained from SPICE simulation for the designed converter are given to verify the performance of the proposed converter for varying load as well as line voltage. Experimental results obtained from a laboratory prototype converter are presented to verify the theory.     

Soft-switching single-stage AC-to-DC converter with low harmonic distortion

A 1 /spl phi/ high-frequency (HF) transformer isolated, soft-switching single-stage ac-dc converter with low line-current harmonic distortion is presented. Its operation is explained with equivalent circuits for the various intervals. The converter is analyzed and design curves are obtained. An optimization parameter is introduced and a systematic design procedure is illustrated with a design example. Detailed SPICE simulation and experimental results of a 500 W converter with load as well as line voltage variation are given to verify theory. The proposed converter employs a zero-voltage transition (ZVT) network to ensure zero-voltage switching (ZVS) at all loads, and natural power factor correction is ensured using a simple control circuit.     

LC并联谐振电路教学中的一个误区

LC并联谐振电路在电子线路中被广泛应用,但是在实际教学中往往存在一个误区,即认为谐振发生时的谐振电阻为最大值,端电压也为最大值。从理论推导出发,借助虚拟实验平台MULTISIM进行仿真,从而论证了实际LC并联谐振发生时谐振电阻并非最大值,端电压也非最大值这一结论。     

A new zero-voltage switching DC/DC boost converter

A pulsewidth-modulated (PWM) zero-voltage-switching quasi-resonant boost converter operating at constant switching frequency is presented. In contrast to the frequency-modulated (FM) zero-voltage-switching quasi-resonant boost converter, this converter possesses better controllability and higher operating performance, and overcomes the instability caused by the parasitic oscillation. The principle of operation and performance of the converter are presented. Its two-dimensional state trajectories and steady-state characteristic curves are derived which are useful for the converter design. Both the SPICE simulation and experimental result agree with the theoretical prediction     

LLC parallel resonant converter design by scaling the LC converter

An efficient and practical method for steady-state design of an LLC-type parallel resonant dc/dc converter (LLC-PRC) is presented. In general, the output characteristic curves of LLC-PRC can be obtained by multiplying the output curves of the LC-type parallel resonant converter (LC-PRC) by a ratio of the parallel and series inductances. The peak voltage and current stresses on the resonant elements also depend on the same ratio. The LLC-PRC with a filter inductor is examined for two conduction modes, continuous and discontinuous capacitor voltage conduction modes, to show the effect of the inductance ratio. A means to use the derived equations to obtain the zero current switching (ZCS) is given. Also, a design procedure, along with design examples, is given to illustrate the use of the equations and characteristic curves. An experimental LLC-PRC is built to ensure the validity of the equations and design examples     

Steady-state analysis and design of a switched-capacitor DC-DCconverter

A representative switched-capacitor DC-DC converter topology is presented, circuit operation is explained, and control strategies are identified. State-space averaging is used to analyze steady-state performance and to develop control criteria and design equations. The analytical results are verified by SPICE simulation     

Tapped-inductor filter assisted soft-switching PWM DC-DC power converter

A novel high-frequency transformer linked full-bridge type soft-switching phase-shift pulsewidth modulated (PWM) controlled dc-dc power converter is presented, which can be used as a power conditioner for small-scale photovoltaic and fuel cell power generation systems as well as isolated boost dc-dc power converter for automotive ac power supply. In these applications with low-voltage large-current sources, the full-bridge circuit is the most attractive topology due to the possibility of using low-voltage high-performance metal-oxide-semiconductor field-effect transistor (MOSFET) and achieving high efficiency of the dc-dc power converter. A tapped-inductor filter including the freewheeling diode is newly implemented in the output stage of the full-bridge phase-shift PWM dc-dc converter to achieve soft-switching operation for the wide load variation range. Moreover, in the proposed converter circuit, the circulating current is effectively minimized without using additional resonant circuit and auxiliary power switching devices. The practical effectiveness of the proposed soft-switching dc-dc power converter was verified in laboratory level experiment with 1 kW 100 kHz breadboard setup using power MOSFETs. Actual efficiency of 94-97% was obtained for the wide duty cycle and load variation ranges.     

A Normalized Model for the Half-Bridge Series Resonant Converter

Closed-form steady-state equations are derived for the halfbridge series resonant converter with a rectified (dc) load. Normalized curves for various currents and voltages are then plotted as a function of the circuit parameters. Experimental results based on a 10-kHz converter are presented for comparison with the calculations.     

Steady-State Analysis of the Series Resonant Converter

The series resonant converter is analyzed in steady state, and for constant switching frequency the output current and voltage characteristics are found to be ellipses. The converter operating point can then be easily obtained by superimposing a load line on these elliptical characteristics. Peak resonant capacitor voltage and inductor current are also plotted in the output plane and are dependent to first order only on output current. When peak voltage and current are plotted in this manner, the dependence of component stresses on operating point is clearly revealed. The output characteristics are modified to include the effect of transistor and diode voltage drops, and experimental verification is presented.     

Analysis of a parallel resonant converter with secondary-sideresonance

A high-frequency (HF) link parallel resonant DC/DC converter operating in the lagging power factor mode with the resonating capacitor on the secondary side of the HF transformer is analyzed using a state-space approach. Closed-form solutions (except for the duration of diode conduction) are obtained for steady-state conditions, and design curves are obtained. A method of obtaining optimum operating point under certain constraints is developed and is used as the basis of a simple design procedure. A theoretical study comparing the performance of three MOSFET-based 1-kW converters with different transformer turn ratios under load changes from rated-load to 10% load is carried out. Experimental results obtained with these converters with different transformer turn ratios are also presented     

A novel resonant converter topology for DC-to-DC power supply

A class-E DC-to-DC converter with half-wave controlled current rectifier is proposed. Its output voltage is controlled by the conduction angle of the rectifier switch at constant switching frequency. Zero voltage switching for all the switches can be maintained from full load to no load. Its steady state characteristics are analyzed and the effects of the circuit parameters are studied. Some extensions of the proposed converter are also discussed. The analysis is verified by PSPICE simulation and an experimental prototype     

Effect of FET output capacitance on ZVS of resonant converters

The analysis of resonant converters including the capacitance of the switches is presented. New dc characteristics are obtained for the series, parallel, and series-parallel resonant converters (SPRC). The operating regions where the converters operate with zero-voltage switching (ZVS) are determined as a function of the switch capacitance. The more pronounced effect can be seen in the series resonant converter (SRC), while the parallel resonant converter (PRC) is the most insensitive. The results of the analysis have been verified on an experimental prototype     

串联输出DC／DC谐振变换器的稳态分析

分析了高于谐振频率工作的串联输出谐振变换器的工作模式,采用状态变量法计算获得了若干描述稳态工作的特性曲线,为分析和设计这种变换器提供了基础     

Single-Stage Single-Switch Switched-Capacitor Buck/Buck-Boost-Type Converter

A new dc-dc converter featuring a steep step-down of the input voltage is presented. It answers a typical need for on-board aeronautics modern power architectures: power supplies with a large conversion ratio able to deliver an output voltage of 1–1.2 V. The proposed structure is derived from a switched-capacitor circuit integrated with a buck converter; they share the same active switch. The proposed solution removes the electromagnetic interference (EMI) emission due to the large di/dt in the input current of the switched-capacitor power supplies. Compared with a quadratic buck converter, it presents a similar complexity, a smaller reduction in the line voltage at full load (but less conduction losses due to smaller input inductor current and capacitor voltage), lower voltage stresses on the transistor and diodes, lower current stresses in the diodes, and smaller size inductors. A similar structure using a buck-boost converter as the second stage is also presented. The experimental results confirm the theoretical developments.     

Single-stage ZVS PWM full-bridge converter

A new soft-switched ac-dc single-stage pulse width modulation (PWM) full-bridge converter is proposed. The converter operates with zero-voltage switching (ZVS), fixed switching frequency, and with a continuous input current that is sinusoidal and in phase with the input voltage. This is in contrast with other ac-dc single-stage PWM full-bridge converters that are either resonant converters operating with variable switching frequency control and high conduction losses, converters whose switches cannot operate with ZVS, or converters that cannot perform power factor correction (PFC) unless the input current is discontinuous. All converter switches operate with soft-switching due to a simple auxiliary circuit that is used for only a small fraction of the switching cycle. The operation of the converter is explained and analyzed, guidelines for the design of the converter are given, and its feasibility is shown with results obtained from an experimental prototype.     

Analysis of series-parallel resonant converter

A frequency-domain steady-state analysis is given for a series-parallel resonant converter (SPRC) operating in the continuous conduction mode (CCM) using Fourier series techniques. Equations for performance parameters are derived under steady-state conditions to provide simple design tools. The topology of the SPRC combines the advantageous properties of both the series resonant converter (SRC) and the parallel resonant converter (PRC). The key results of the work are: a novel half-wave rectifier SPRC, conditions for obtaining high part-load efficiency; and several boundary frequencies and limiting conditions such as the capacitive/inductive load boundary and open-circuit and short-circuit cases. Experimental results measured for an 80-W converter above the resonance at different load resistances and input voltages show excellent agreement with the theoretical performance predicted by the equations