共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
3.
《燃气涡轮试验与研究》2014,(2)
为研究燃烧环结构对涡轮叶间燃烧室的性能影响,通过改变燃烧环的径向长度,设计出6种不同长宽比的燃烧环模型,并利用FLUENT软件的Realizable k-ε湍流模型、PDF燃烧模型和离散相模型,对涡轮叶间燃烧室三维两相流场进行了数值模拟。结果表明:受高温燃气与主流掺混程度的影响,不同长宽比燃烧环内速度场及温度场差异明显,从而影响燃油液滴驻留时间和出口温度分布;合理选择燃烧环的长宽比,能有效改善涡轮叶间燃烧室的燃烧效率、总压损失和温度分布。本研究可为涡轮叶间燃烧室优化设计提供参考。 相似文献
4.
为探究涡轮叶片径向槽轴向长度对超紧凑燃烧室性能的影响,对3种不同轴向长度的径向槽分别在2种当量比条件下,用FLUENT软件对超紧凑燃烧室内流动及燃烧进行了数值模拟。结果表明:随着径向槽轴向长度的减小,燃烧环内未完全燃烧的微小燃油颗粒和燃气沿着槽的径向迁移量也减少,从而使燃油颗粒和燃油蒸气在燃烧环内的驻留时间增加;当叶片径向槽的轴向长度与燃烧环轴向长度之比等于0.75且燃烧环当量比为0.81时,燃烧室的燃烧性能较好。这对超紧凑燃烧室的优化设计有重要的参考价值。 相似文献
5.
《燃气涡轮试验与研究》2017,(6)
正涡轮内增燃技术,即在涡轮内增加燃烧室,喷油再次燃烧,以提高热力循环性能。国外在上世纪末就开始了此项技术的研究,提出了涡轮内增燃技术的概念及射流涡流结构方案,即涡轮叶间燃烧室(TIB)。该技术利用周向二次射流产生的旋流离心力进行离心燃烧,在稳定燃烧的同时提高航空发动机的推重比。 相似文献
6.
7.
选取二次射流流量变化和环境压力变化的工况条件,对涡轮燃烧射流涡流方案的影响进行研究。其中,二次射流流量变化时,环境压力保持101 325 Pa不变;环境压力变化时,二次射流流量保持0.014 kg/s不变。采用基于压力的隐式稳态求解器模拟涡轮内增燃燃烧室的流动与燃烧过程,并在模拟过程中应用尺度适应模拟湍流模型(SAS)。研究表明:随着二次射流流量的增加,射流涡流燃烧室内温度分布均匀化、总压损失增加、燃烧效率提高、污染物降低;随着环境压力的增大,射流涡流燃烧室内温度分布不受影响,但总压损失降低、燃烧效率提高、污染物降低。 相似文献
8.
9.
采用两大类模型,对应用射流涡流燃烧结构方案的高压涡轮导向器性能进行数值模拟研究。利用基于压力的隐式稳态求解器以及尺度适应模拟湍流模型(SAS),完成了涡轮内增燃燃烧室内的流动与燃烧过程的数值模拟。研究结果表明:无论是在高压涡轮导向器顶部还是在底部耦合驻涡凹腔,对导向器叶间流场形态、流体流动转折角、导向器叶间静压力场的形态以及分布、总压损失均无明显影响,维持了原有导向器的基本性能;高压涡轮导向器耦合射流涡流燃烧结构,增加了涡轮叶片叶间的平均温度以及涡轮导向器出口的平均温度。 相似文献
10.
为了使航空发动机达到高推质比、低燃油消耗率、低污染以及拓宽稳定工作范围的目标,应使用涡轮导向器增燃技术在涡轮导向器叶片间喷油点火再次燃烧,提高涡轮内燃气温度,从而提高发动机的总体性能.阐述了涡轮导向器增燃技术具有提高航空发动机总体性能的潜在优势,分析研究了该技术中组织燃烧的关键技术、参数和机理问题,得出如下结论:①对于射流旋流方案,径向凹槽对燃烧室出口温度分布起决定性作用;降低燃烧凹环内当量比,可提高燃烧效率,从而降低CO,UHC(未燃碳氢化合物),NOx等污染物排放量.②当二次气流角为60°时,射流涡流方案各项燃烧性能较好. 相似文献
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:3,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
13.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
14.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
15.
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
16.
17.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
18.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
19.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
20.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献