基于谐振舵面的跨声速抖振抑制探究

跨声速抖振引起的非定常脉动载荷会造成飞行器结构疲劳甚至引发飞行事故,所以跨声速抖振的控制研究逐渐成为航空领域的热点。采用基于Spalart-Allmaras(S-A)湍流模型的非定常雷诺平均方程开展了基于谐振舵面的跨声速抖振抑制研究。首先验证静止NACA0012翼型的抖振边界和频率特性,然后分别从舵偏平衡位置、舵偏幅值、频率以及相角等角度研究了谐振舵面的控制效果。舵偏平衡位置等效于减小了翼型的有效迎角;幅值和频率对抖振抑制效果影响较大,当舵面振荡频率与抖振频率接近时发生共振现象;相角对控制效果有一定影响,在270°相角附近,升力系数幅值减小了60%。在合适的舵偏幅值、频率以及相角组合下,谐振舵面有可能成为跨声速抖振的有效开环控制策略。     

超临界翼型跨声速抖振CFD计算和POD分析

使用二阶迎风Roe格式、隐式时间推进和S-A(Spalart-Allmaras)一方程湍流模型,通过求解基于格心格式有限体积法的RANS方程模拟了OAT15A超临界翼型的跨声速抖振流场。在模拟出激波/附面层相互干扰诱发的抖振现象的基础上,对翼面激波运动过程中的气流分离泡变化规律开展研究,揭示出激波变化相位略微超前于升力系数相位的非定常现象。为剖析跨声速抖振的物理成因,将抖振计算的非定常解作为快照,应用本征正交分解POD(Proper Orthogonal Composition)方法提取POD模态,从流场相干结构的角度对跨声速抖振现象进行了分析。     

激波控制鼓包提高翼型跨声速抖振边界

翼型抖振边界是仅次于升阻比的一项重要气动指标.采用定常雷诺平均Navier-Stokes方程,以升力线斜率平缓及激波位置振荡作为基本判据确定了RAE2822翼型在指定跨声速来流条件下的抖振边界.通过大量计算流体力学(CFD)验证,针对RAE2822翼型设计了一种特定外形的激波控制鼓包并确定了其具体安装位置.该激波控制鼓...     

机翼跨声速抖振研究进展

跨声速飞行中,激波附面层干扰会引起激波周期性自激振荡,这种现象称之为跨声速抖振。跨声速抖振引起的脉动载荷有可能造成结构疲劳甚至引发飞行事故,该问题一直是航空领域的研究难点。本文从风洞试验和数值模拟两个方面总结了跨声速抖振研究的主要方法,重点综述了近几年在跨声速抖振机理研究方面以及结构运动对抖振响应特性的影响方面取得的新进展,简要总结了跨声速抖振的被动控制及主动控制方法。在此基础上,提出了跨声速抖振后续研究的重点方向:抖振机理的进一步探究,结构弹性特征对抖振特性的影响以及闭环主动控制等。     

基于POD和DMD方法的跨声速抖振模态分析

跨声速抖振现象是由于非定常跨声速流动中激波的自激振荡而引起的结构强迫振荡,这种现象在跨声速飞行器中普遍存在,对飞机的结构强度和疲劳寿命有不利影响。基于模态分解的分析方法是进一步发展抖振控制手段的有效工具。本文通过两类典型模态分析方法（本征正交分解（POD）和动态模态分解（DMD））对OAT15A翼型的跨声速抖振现象进行分析,通过对模态频率、翼面压力分布、流场重构误差等方面的研究,将两种模态分解方法进行对比。发现基于频率特征的DMD方法能够准确捕捉抖振的临界稳定特征和抖振主频的典型模态,同时能够更准确反映流场变量在激波间断附近随时间的变化过程;而POD方法尽管在流场重构时具有较小的总体误差,但对激波附近压强随时间的变化历程拟合较差。     

超临界翼型跨声速激波振荡数值模拟

应用DES(detached eddy simulation)方法研究了SC(2)-0714超临界翼型跨声速自维持激波振荡现象.使用的DES方法预测了激波在翼型上表面的周期性运动,分析了雷诺数对激波运动的减缩频率、平均激波位置、脉动压力系数等非定常特性的影响.结果表明:雷诺数对激波振荡运动特性的影响呈非线性关系;而雷诺数为6×106时的激波振荡运动特性与雷诺数分别为15×106及30×106时的特性存在明显差异.      

激波—边界层被动控制概念的实验研究

本文通过运载火箭模型的跨声速风洞试验,研究了运用激波-边界层被动控制降低模型表面脉动压力和阻力的效果,并得出了开孔区表面的开孔率、开孔方式和空腔深度对脉动压力系数的影响规律,探讨了激波-边界层被动控制的机理。     

跨声速翼型激波／边界层干扰被动控制的数值模拟计算

本文应用数值计算的方法着重研究了跨声速翼型开孔壁的减阻效果。计算采用了边界层与位流相互作用的模型,藉以了解开孔壁对激波强度及结构的影响和对边界层控制的效果。通过对NACA0012翼型的计算表明,本文采用的自然吹吸的开孔模型能够显著地削弱激波的强度,改善激波的结构,但会使粘性损失增加。在马赫数较小时,翼型开孔后总阻力会增加,而在大马赫数时,开孔翼型的减阻效果才表现出来。这种趋势是与实验结果相吻合的。     

跨声速翼型上激波／边界层干扰的自适应控制计算

在激波区使用自适应壁对跨声速翼型上的激波/边界层干扰进行控制,可改变机翼的气动性能。这种被动控制可通过在翼型的激波区开一凹腔,其上覆盖一弹性橡胶膜柔壁来实现。本文给出用N-S方程数值模拟这一自适应控制翼型的跨声速粘性绕流,提出了一个适用于本特殊情况(物面边界局部地区在求解过程中有变化)的处理办法。并探讨了自适应柔壁对当代跨声速翼型绕流的影响。     

机翼跨声速抖振数值模拟及模态分析

绕机翼的跨声速抖振流动是典型的复杂不稳定流动，对其非定常特性及失稳机制的研究具有重要的工程和学术价值。通过非定常雷诺平均Navier-Stokes（URANS）仿真方法和动模态分解（DMD）分析手段，研究了CRM（Common Research Model）等典型机翼的跨声速抖振流动特性及其主要失稳模态。数值仿真结果表明机翼的跨声速抖振表现为多失稳模式下的宽频特性。除了激波的弦向失稳，还会伴随发生激波的展向失稳，它们都表现为低频特性。翼梢处的高频响应可能是由激波诱导的低频失稳与翼尖涡相互耦合形成。DMD分析结果显示机翼展长和后掠因素诱导了激波展向失稳模态。本研究对抖振流动的物理建模、控制及理解相关的气动弹性现象具有指导意义。     

Self-sustained shock oscillations on airfoils at transonic speeds

Self-sustained shock wave oscillations on airfoils at transonic flow conditions are associated with the phenomenon of buffeting. The physical mechanisms of the periodic shock motion are not yet fully understood even though experiments performed over fifty years ago have demonstrated the presence of oscillatory shock waves on the airfoil surfaces at high subsonic speeds. The unsteady pressure fluctuations generated by the low-frequency large-amplitude shock motions are highly undesirable from the structural integrity and aircraft maneuverability point of view. For modern supercritical wing design with thick profiles, the shock-induced fluctuations are particularly severe and methods to reduce the shock wave amplitudes to lower values or even to delay the oscillations to higher Mach numbers or incidence angles will result in expanding the buffet boundary of the airfoil. This review begins with a recapitulation of the classical work on shock-induced bubble separation and trailing edge separation of a turbulent boundary layer. The characteristics of the unsteady pressure fluctuations are used to classify the types of shock-boundary layer interaction. The various modes of shock wave motion for different flow conditions and airfoil configurations are described. The buffet boundaries obtained using the standard trailing edge pressure divergence technique and an alternative approach of measuring the divergence of normal fluctuating forces are compared to show the equivalence. The mechanisms of self-sustained shock oscillations are discussed for symmetrical circular-arc airfoils at zero incidence and for supercritical airfoils at high incidence angles with fully separated flows. The properties of disturbances in the wake are examined from linear stability analysis of two-dimensional compressible flows. The advances in high-speed computing make predictions of buffeting flows possible. Navier–Stokes solvers and approximate boundary layer-inviscid flow interaction methods are shown to give good correlation of frequencies and other unsteady flow characteristics with experiments. Finally, passive and active methods of shock oscillation control show promising results in delaying buffet onset to higher Mach numbers or incidence angles, thus enhancing the transonic performance of airfoils.     

Transonic buffet control research with two types of shock control bump based on RAE2822 airfoil

Current research shows that the traditional shock control bump (SCB) can weaken the intensity of shock and better the transonic buffet performance.The author finds that when SCB is placed downstream of the shock,it can decrease the adverse pressure gradient.This may prevent the shock foot separation bubble to merge with the trailing edge separation and finally improve the buffet performance.Based on RAE2822 airfoil,two types of SCB are designed according to the two different mechanisms.By using Reynolds-averaged Navier-Stokes (RANS) and unsteady Reynolds-averaged Navier-Stokes (URANS) methods to analyze the properties of RAE2822 airfoil with and without SCB,the results show that the downstream SCB can better the buffet performance under a wide range of freestream Mach number and the steady aerodynamics characteristic is similar to that of RAE2822 airfoil.The traditional SCB can only weaken the intensity of the shock under the design condition.Under the off-design conditions,the SCB does not do much to or even worsen the buffet performance.Indeed,the use of backward bump can flatten the leeward side of the airfoil,and this is similar to the mechanism that supercritical airfoil can weaken the recompression of shock wave.     

Experimental investigation of shock-buffet criteria on a pitching airfoil

An experimental investigation of the shock-buffet phenomenon subject to unsteady pitching supercritical airfoil around its quarter chord has been conducted in a transonic wind tunnel. The model was equipped with pressure taps connected to the fast response pressuretransducers. Measurements were conducted at different free-stream Mach number from 0.61 to0.76. The principle goal of this investigation was to experimentally discuss the shock-buffet criterion over a SC(2)-0410 supercritical pitching ...     

Characteristic analysis of lock-in for an elastically suspended airfoil in transonic buffet flow

Numerical simulations are performed to study the aeroelastic responses of an elastically suspended airfoil in transonic buffet flow, by coupling the unsteady Reynolds-averaged Navier-Stokes (RANS) equations and structural motion equation. The current work focuses on the char-acteristic analysis of the lock-in phenomenon. Great attentions are paid to studying the frequency range of lock-in and the effects of the three parameters, namely the structural natural frequency, mass ratio and structural damping, on lock-in characteristic of the elastic system in detail. It is found that when the structural natural frequency is close to the buffet frequency, the coupling fre-quency of the elastic system is no longer equal to the buffet frequency, but keeps the same value as the structural natural frequency. The frequency lock-in occurs and stays present until the structural nature frequency is near the double buffet frequency. It means that the lock-in presents within a broad range, of which the lower threshold is near the buffet frequency, while the upper threshold is near the double buffet frequency. Moreover, the frequency range of lock-in is affected by mass ratio and structural damping. The lower the mass ratio and structural damping are, the wider the range of lock-in will be. The upper threshold of lock-in grows with the mass ratio and structural damping decreasing, but the lower threshold always keeps the same.     

Flow characteristics around airfoils near transonic buffet onset conditions

In transonic flow, buffet is a phenomenon of flow instability caused by shock wave/boundary layer interaction and flow separation. The phenomenon is common in transonic flow, and it has serious impact on the structural strength and fatigue life of aircraft. In this paper, three typical airfoils: the supercritical OAT15A, the high-speed symmetrical NACA64A010, and the thin, transonic/supersonic NACA64A204 are selected as the research objects. The flow fields of these airfoils under pre-buffet and buffet onset conditions are simulated by Unsteady Reynolds Averaged Navier-Stokes (URANS) method, and the mode analysis of numerical results is carried out by Dynamic Mode Decomposition (DMD). Qualitative and quantitative analysis of the shock wave motion, shock wave intensity, shock foot bubble and trailing edge separation, and pressure coefficient fluctuation were performed to attain deep insight of transonic buffet flow features of different airfoils near buffet onset conditions. The results of DMD analysis show that the energy proportion of the steady mode of these airfoils decreases dramatically when approaching the buffet onset angle of attack, while the growth rate of the primary mode increases inversely. It was found that at the onset of buffet, there exist different degrees of merging behavior between shock foot bubble and trailing edge separation during one buffet cycle, and the instability of shock wave and separation induced shear layer are closely related to the merging behavior.