共查询到20条相似文献,搜索用时 593 毫秒
1.
动态孔径分割技术为相控阵雷达针对不同任务灵活分配孔径资源提供了可能,而传统的资源调度方法仅基于单一孔径条件研究了时间资源的优化分配问题。针对雷达搜索、跟踪与成像任务的自适应调度问题,提出了一种基于时间-孔径二维资源管理的雷达资源调度算法。该算法建立了雷达孔径分割条件下的二维资源调度模型,确立了能量资源约束条件;利用基于压缩感知的稀疏孔径逆合成孔径雷达(ISAR)成像技术,使雷达在完成目标搜索和跟踪任务的同时实现对目标的成像;定义了调度算法性能的评价指标。在仿真实验中将该算法与另外2种算法进行对比,验证了所提算法在高度成功率、二维资源利用率与任务并行度这3种性能指标上具有优越性。 相似文献
2.
相控阵雷达可以同时担负搜索、跟踪、识别与成像等多种雷达任务。为了提高雷达对战场环境的感知能力并减轻雷达资源分配的冲突,提出一种微动目标跟踪成像一体化的雷达资源优化调度算法。该算法建立了包含微动目标成像任务的雷达优化调度模型并利用启发式算法求解,利用跟踪脉冲与调度剩余的空闲时间资源,动态地构造感知矩阵并采用正交匹配追踪(OMP)算法对微动目标进行特征提取并成像。仿真结果表明:该算法可以实现稀疏孔径条件下的微动目标成像,并具有良好的鲁棒性,同时进一步提高了雷达系统的资源利用率。 相似文献
3.
4.
针对相控阵雷达多目标跟踪波束调度和波形参数优化控制的问题,本文提出了一种基于马尔可夫决策过程(MDP)的相控阵雷达跟踪波束调度与波形参数优化策略,该方法以无迹卡尔曼滤波(UKF)算法为基础来估计目标的状态。首先将本文的序列决策问题建模为马尔可夫决策过程,定义了资源的效费比和长期回报率,然后与当前实际跟踪误差综合考虑作为MDP的回报函数,进而给出了调度的优化模型,最后将长时决策问题转化为动态规划算法结构进行求解,并且提出了一种并行混合遗传粒子群优化算法来求解各决策时刻的最优策略。仿真结果表明了长时策略的先进性以及寻优算法的优越性,与传统的短时策略相比,跟踪精度可提高11.17%。 相似文献
5.
如何有效分配有限的能量和时间资源,从而实现大量密集群目标的跟踪测量,是相控阵雷达资源调度面临的难点问题。在采用基于最小期望时间和时间槽优先占用的自适应资源调度模型的基础上,论述了基于波位动态聚类及分区识别算法的相控阵雷达群目标调度模型,详细描述了群目标调度流程图。群目标调度模型根据距离门宽度、方位俯仰波束宽度、目标速度、航迹预测误差和点迹测量误差等确定群目标的分区位置及大小,自动实现群目标的聚类和跟踪。仿真分析表明:该模型能够适应目标群的动态演化过程,实现群内外所有目标的独立跟踪,有效节约群目标跟踪时的资源开销,并已在实际工程应用中得到了验证。 相似文献
6.
7.
8.
随着现代战场中电子对抗的日益激烈,雷达的生存环境受到了严重的威胁。射频(RF)隐身技术是一种提高雷达及其运载平台战场生存能力的重要途径。为提高雷达射频隐身性能,针对具有MIMO探测模式的新体制雷达提出了隐身性能优化的目标跟踪算法。该算法基于射频隐身性能优化模型,通过自适应控制系统的子阵划分个数、平均发射功率、波束驻留时间以及采样周期,在满足系统跟踪性能要求的前提下优化系统射频隐身性能,其中的射频隐身性能综合考虑了截获因子及采样周期。仿真结果表明,与传统相控阵雷达相比,本文所提出的目标跟踪算法使MIMO雷达具有更好的射频隐身性能。 相似文献
9.
一种新的基于机动检测的机动目标跟踪算法 总被引:3,自引:0,他引:3
针对Kalman滤波跟踪机动目标发散和目前多数自适应Kalman滤波算法对运动模型适应性不强的问题,提出了一种新的基于机动检测的机动目标跟踪算法,通过实时自适应的改变滤波模型提高对机动目标跟踪精度。对这种方法与Kalman滤波算法进行了计算机仿真比较,结果表明,该方法计算量小,可实时精确地自适应匹配目标的运动模型,可实现对机动目标稳定可靠的跟踪。 相似文献
10.
针对敏捷遥感卫星对多个离散观测点在轨自主任务规划问题,在考虑姿态运动方程耦合性的基础上,将问题分解为空间资源调度问题和连续最优控制问题,进而提出了一种结合伪谱法和遗传算法的混合求解算法。该算法针对基于行商问题(TSP)模型建立的空间资源调度问题模型,选用二维编码结构对观测顺序和相对观测时间进行实数编码,并采用遗传算法求解观测序列和观测时间;针对判断观测时间可行性时涉及的时间最优控制问题、以及姿态转移过程中涉及的最小能量消耗问题,将其归结为连续最优控制问题,并基于Gauss伪谱协态变量映射定理,采用Gauss伪谱法进行求解。通过与基于单纯遗传算法的规划算法进行对比试验,本文所提出的基于伪谱法和遗传算法的混合求解策略针对目标问题,在典型工况下姿态转移过程中能量消耗降低60%。 相似文献
11.
12.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
13.
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
14.
15.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
16.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
17.
18.
19.
航天器返回地球的气动特性综述 总被引:4,自引:0,他引:4
航天器返回地球的飞行过程中,气动特性是实现将宇宙飞行速度减到落地前速度、保证再入飞行得到有效控制以及再入防热安全可靠的关键因素。针对简单旋成体气动外形、半弹道式再入控制、烧蚀防热类返回航天器,综述了返回地球过程中变化的空气流域特性、航天器周围的气体绕流环境、空气与航天器作用产生的动力学与热效应等。系统地给出了该类航天器的再入气动特性参数与飞行性能的共性规律,包括:气动阻力与再入减速、气动升力与再入轨迹控制、配平攻角与飞行稳定性、气动加热与防热,以及再入过程中不同气动特性航天器、气象条件变化等对再入飞行性能的影响规律。为航天器开展返回飞行过程的跨流域气动性能工程研制提供设计参考。 相似文献
20.
FU Hong-jun MA Chong-qi KUANG Nai-hang LUAN Shi-lin 《中国航空学报》2007,20(2):124-128
This work was dedicated to performing surface oxidation and coating treatments on carbon fibers (CF) and investigating the changes of fiber surface properties after these treatments, including surface composition, relative volume of functional groups, and sur- face topography with X-ray photoelectron spectroscopy (XPS) and atom force microscopy (AFM) technology. The results show that, after oxidation treatments, interfacial properties between CF and non-polar polyarylacetylene (PAA) resin are remarkably modified by removing weak surface layers and increasing fiber surface roughness. Coating treatment by high char phenolic resin solution after oxida- tion makes interface of CF/PAA composites to be upgraded and the interfacial properties further bettered. 相似文献