一种多径条件下的MLS接收机测角误差分析新方法

为了准确分析多径环境条件下微波着陆系统接收机测角误差,在深入分析微波着陆系统(MLS)测角原理的基础上,提出了一种基于扫描波束主瓣等效替代的误差分析方法。该方法通过把往返波束脉冲主瓣用高斯钟形替代,准确计算了接收的扫描脉冲-3dB门限前后沿误差,建立了多路径条件下统一实用的接收脉冲包络波峰位置偏移误差模型和锁住闸门测量误差模型。为验证模型准确性,以特定的多径环境条件为例,计算MLS接收机的测角误差,将计算结果与利用Mathias经典模型的计算结果进行对比,并通过计算机仿真进行验证。结果表明,采用主瓣替代方法能够较好地克服经典模型精确分析误差方面的使用不足和缺陷,且对多径条件下接收机测角精度的准确评定具有一定的实用价值。     

不同参数对直升机铰接式旋翼气流失速边界的影响的研究

本文分析了直升机铰接式旋翼气流失速边界受马赫数，攻角，俯仰和侧倾角速度，浆叶方位角位置的影响，得出了确定气流失速边界的公式。     

Fast alignment and calibration algorithms for inertial navigation system

Algorithms for fast estimating the azimuth misalignment angle and calibrating gyro drift rates are approached from the point of view of control theory. By introducing the Lyapunov transformation, the equivalence of Strapdown Inertial Navigation System (SINS) and Gimbaled Inertial Navigation System (GINS) is discussed, and it shows that the analysis results of GINS can be applied to SINS directly by using such kind of equivalence. A similar transformation that based on physical essence is introduced, so that the true states can be replaced by the so-called pseudo-states, and then the observable states of INS can be dynamically decoupled with the unobservable states. Consequently, the best completely observable subsystem model of INS can be obtained. Based on the simplified subsystem model of INS, the algorithms for fast estimating the azimuth misalignment angle and calibrating gyro drift rates are proposed. The proposed algorithms show that the azimuth misalignment angle and gyro drift rates can be estimated from the rates of leveling misalignment angles without using the gyro output signals.     

机载单通道雷达实波束扫描的前视探测

针对机载单通道雷达采用合成孔径雷达(SAR)技术、多普勒波束锐化(DBS)技术等途径难以实现载机飞行路线正前方高分辨率成像问题,研究了一种利用方位实波束重叠扫描的新型机载单通道雷达前视探测方法,讨论了提高方位分辨率的可行性和适用条件。该方法根据目标回波强度受到波束扫描增益调制的特点,通过计算修正的Capon空间谱来实现方位超分辨。模拟实验表明,所提方法能够实现机载单通道雷达的前视成像,可以显著提高波束主瓣区域内强弱临近目标的分辨能力。     

陆用惯性导航系统非线性对准方法

以某型自行火炮炮载惯性导航系统为研究对象。为解决大方位失准角造成的系统非线性问题,在对大失准角误差模型进行详细分析的基础上,提出了基于快速正交搜索（FOS）和卡尔曼滤波（KF）的非线性参数估计方法。利用事先训练好的非线性误差模型进行对准,既能消除线性姿态误差,又可以对非线性姿态误差起到良好的抑制作用。仿真结果表明,FOS/KF方法的对准精度和实时性远优于扩展卡尔曼滤波（EKF）。对比试验结果表明,单独使用EKF时的方位角误差最大达到14.99°,而FOS/KF可以使方位角误差保持在0.8°以内。FOS/KF方法的估计精度不随系统非线性程度的变化而变化,并且不需要进行粗对准,简化了对准过程,提高了载体机动性。     

圆台阵列杂波模型及空时二维自适应处理

针对圆台共形阵列,建立了空时二维自适应处理(STAP)的杂波模型,给出了圆台阵列杂波抑制最优权值的计算方法。在此基础之上,为了实现可应用到实际环境中的自适应处理方法,进一步讨论了将局部联合域(JDL)降维算法推广至圆台阵列中的问题。得出了圆台阵列JDL算法降维变换矩阵的表达形式,研究了参考波束的数目选取、波束指向等因素对降维损失的影响。理论分析以及仿真结果表明,通过合理选择通道数、波束方位向指向间隔等参数,该算法能够减少自适应波束形成的计算量,而且可以用较少的训练样本获得较好的处理性能。     

Properties of Staggered PRF Radar Spectral Components

Expressions for moving target indicator (MTI) improvement factor limitation due to pulse repetition frequency (PRF) staggering and loss of target detectability for various values of Doppler frequency in the passband are presented. It is also shown that the product of variance of stagger periods and clutter variance is an important parameter determining the performance of a staggered PRF MTI radar.     

基于闭路制导的弹道导弹发射诸元的仿真算法

提出了一种基于闭路制导的弹道导弹的发射诸元算法.给定发射点与瞄准点的地理位置,以压低弹道为目标,通过一种迭代方法求解关机点弹道倾角,并基于地球引力级数展开模型提出了一种虚拟目标的快速计算方法,以主动段弹道平面和被动段弹道平面二面角为指标完成了发射方位角的迭代计算,最后通过仿真算例论证了该算法的可行性.     

Reduction of Radar Tracking Errors with Frequency Agility

Frequency agility with random frequency in each pulse gives an improvement in radar angle tracking with a monopulse radar. With a conical-scan tracking radar, the glint error is reduced but fading error can be increased, and the net result must be studied in each case. A theory, usable for calculating angle tracking errors with a frequency agile radar, is given, and two examples showing the error reduction are presented. According to the theory, one part of the glint or fading spectra is ``smeared out' to half the pulse repetition frequency. Another part, the size of which depends on the degree of correlation between pulses, keeps the form of the original spectrum.     

TDRSS中用户星的星-星天线跟踪规律深入研究

应用坐标转换，得到用户星的星-星天线基本跟踪规律。针对几种情况，并考虑地球的隔断影响和天线的自身限制，对星一星天线的方位角和俯仰角表达式进行了修正和补充。最后，针对某用户星，应用Matlab进行数学仿真。结果表明，根据得出的跟踪规律，可以使用户星的星一星天线最大范围地跟踪中继卫星。     

ARTEMIS: a positioning system

ARTEMIS is an acronym for: automatic ranging theodolite emitting microwave signals. The reference direction in azimuth is obtained by mounting a theodolite on the antenna, aiming it at a known position in the field and adjusting the azimuth reading. About 300 ARTEMIS sets, in various configurations, have been sold and, in spite of its much higher price when compared with DGPS, sales are continuing. Many sets were made gastight in view of security requirements on platforms. It is shown how a plotter can determine the course driven by a car on the road. The pen indicates accurately where the car was on the map. Advances in the technique of optical angle encoders are discussed     

舰载机综合光电着舰引导信息融合

飞机着舰过程对着舰引导信息的精度要求非常高,为了更好地辅助飞行员着舰或者实现舰载机自主着舰,文章将电子着舰系统和光学助降系统提供的引导信息进行融合,实现了电子与光学着舰信息的综合运用。其中,电子着舰系统提供斜距、方位仰角和方位偏航角,光学助降系统提供方位仰角和方位偏航角。仿真结果表明,该方法提供的着舰引导信息精度高。     

缝隙目标电磁散射特性试验

 通过对目标结构进行合理设计,可以在一定角域内显著减小雷达散射截面(RCS)。对飞行器表面常见锯齿缝隙的散射特性进行了研究。在微波暗室内对锯齿缝隙分别沿俯仰角变化、方位角变化的减缩效果进行测试。俯仰角变化时,锯齿缝隙有较好的减缩作用,以114°锯齿缝隙在试验中减缩效果最好。方位角变化时,对114°锯齿缝隙进行了多频段测试,并与相应直缝隙进行了对比研究,结果表明,通过选取合适的方位角角域,锯齿缝隙的减缩作用会随入射波频率的升高和仰角的增大而显著增强。结论可为高性能隐身飞行器外形隐身设计提供参考。     

基于频移递推的机载单站无源测距

在机载站飞行方向前方某一距离处的多普勒频移能够通过递推计算的方法由站点当前位置处的相位测量结果而被直接确定。进一步利用频移和角度之间的变换,由多普勒频移的虚拟递推值即可求得载机飞行路线前方虚拟距离处的目标方位,由此就可在机载单站平台上通过三角定位法,实现仅基于相差测量的无源测距。     

全姿态飞机捷联式系统姿态角的计算

本文讨论了飞机做全姿态角运动时捷联式系统姿态角计算中存在的几个问题:（1）为保证单值地确定飞机在空间的角位置,应恰当地规定姿态角的定义域;（2）由方向余弦矩阵元素求姿态角时要进行反三角函数运算,当反三角函数的自变量的分母或分子趋于零时会引起较大的误差,甚至导致计算机溢出,这些都应设法避免;（3）当俯仰角趋于±90°附近的小锥形区域时,三个姿态角自由度退化为两个自由度,这时姿态角的定义与计算方法应做新的改变。本文分析与解决了上述问题,给出了计算姿态角的程序框图。数学模拟的结果证明了理论分析的正确性。     

一种基于数字细分技术的万工显技改方法

讨论了万工显测量系统的基本原理，提出了一种用数字细分技术(A／D转换技术)实现栅距脉冲软件细分的方法。以8位数字量按八区间划分为例，给出了小数值的计算公式并分析了细分误差。实验表明，该方法具有较大的工程实用价值。     

High Range-Resolution Monopulse Tracking Radar

High range-resolution monopulse (HRRM) tracking radar which maintains wide instantaneous bandwidth through both range and angle error sensing channels provides range, azimuth, elevation, and amplitude for each resolved part of the target. The three-dimensional target detail can be used to improve and extend radar performance in several ways: for improved precision of target location, for target classification and recognition, to counter repeater-type ECM, to improve low-angle multipath tracking, to resolve multiple targets, as a miss-distance measurement capability, and for improved tracking in chaff and clutter. These have been demonstrated qualitatively except for the ECCM to repeater ECM and low-altitude tracking improvement. Initial results from an experimental HRRM radar with 3-ns pulse length show resolution of aircraft into its major parts and precise location of each resolved part accurately in range and angle. Realtime closed-loop tracking is performed on aircraft in flight using high-speed sampled, digitized, and processed HRRM range and angle video data. Clutter rejection capability is also demonstrated.     

Azimuth-Elevation Estimation Performance of a Spatially Dispersive Channel

A model is presented for the estimation of azimuth and elevation in a dispersive media where the signals come from a continuum of directions. These bounds depend upon the array ambiguity patterns and the channel spread function. Specific cases are discussed showing how the result reduces to an easily tractable analytical tool in many cases of interest. The model discussed is applicable to angular estimation performance in the presence of such interference as diffuse multipath, chaff clouds, vertical angle of arrival spread in sonar systems, and turbulent and multiply scattered optical channels.     

基于超短基线声传感器阵的高速目标轨迹估计

针对低空高速飞行目标跟踪问题，首先研究了某典型目标噪声信号的时频特性，发现其信号呈现宽带低频特征，难以从频域对目标轨迹进行估计。在此基础上，从各路接收信号的到达时延量入手，考虑到声基阵只能布设于有限空间内的制约，提出了一种基于超短基线阵时延估计的目标跟踪方法。该方法利用各个超短基线阵接收声强极值点分别估计目标运动轨迹垂线方向，计算多个垂线的叉乘向量实现对目标运动方向的估计，再利用多面交汇的方式获估计得到目标运动轨迹。分别对目标俯仰角、方位角及运动轨迹估计的理论误差进行了推导，根据理论估计误差，为能够实现对目标运动轨迹的估计，各个超短基线阵应尽量保证与目标运动轨迹不在同一平面上。根据仿真结果，在采用4个传感器基阵时，角度估计平均误差在4°以内，位置估计相对误差在5%左右。仿真结果验证了该方法的有效性。     

Digital Beamforming on Receive: Techniques and Optimization Strategies for High-Resolution Wide-Swath SAR Imaging

Synthetic Aperture Radar (SAR) is a well-proven imaging technique for remote sensing of the Earth. However, conventional SAR systems are not capable of fulfilling the increasing demands for improved spatial resolution and wider swath coverage. To overcome these inherent limitations, several innovative techniques have been suggested which employ multiple receive-apertures to gather additional information along the synthetic aperture. These digital beamforming (DBF) on receive techniques are reviewed with particular emphasis on the multi-aperture signal processing in azimuth and a multi-aperture reconstruction algorithm is presented that allows for the unambiguous recovery of the Doppler spectrum. The impact of Doppler aliasing is investigated and an analytic expression for the residual azimuth ambiguities is derived. Further, the influence of the processing on the signal-to-noise ratio (SNR) is analyzed, resulting in a pulse repetition frequency (PRF) dependent factor describing the SNR scaling of the multi-aperture beamforming network. The focus is then turned to a complete high-resolution wide-swath SAR system design example which demonstrates the intricate connection between multi-aperture azimuth processing and the system architecture. In this regard, alternative processing approaches are compared with the multi-aperture reconstruction algorithm. In a next step, optimization strategies are discussed as pattern tapering, prebeamshaping-on-receive, and modified processing algorithms. In this context, the analytic expressions for both the residual ambiguities and the SNR scaling factor are generalized to cascaded beamforming networks. The suggested techniques can moreover be extended in many ways. Examples discussed are a combination with ScanSAR burst mode operation and the transfer to multistatic sparse array configurations.