TC4-DT钛合金磨削表面特性及其摩擦磨损性能

钛合金是一种典型难磨削加工材料,磨削表面易出现烧伤、裂纹等热损伤。本文开展了TC4-DT钛合金磨削实验,通过扫描电镜（SEM）、能谱（EDS）、X射线衍射（XRD）、显微硬度仪、金相显微镜及球-盘摩擦磨损实验仪研究了其表面特性及摩擦磨损性能。结果表明：低速磨削表面质量好,摩擦磨损性能较基体略提高;当砂轮线速度为80 m/s时,磨削表面质量良好,摩擦系数为0.38,较基体降低40%;而砂轮线速度为100 m/s时,磨削表面出现严重烧伤、网状裂纹。因此选择合理的高速磨削工艺可避免烧伤、裂纹等热损伤缺陷,并可有效改善表面摩擦磨损性能;磨削表面干摩擦磨损机制为磨粒磨损、粘着磨损和剥层磨损。     

TC4钛合金高效磨削加工用环形热管砂轮的研制

针对航空航天高强韧性难加工材料TC4钛合金在磨削加工中存在磨削温度高而导致工件表面烧伤的问题,提出利用热管换热技术冷却磨削弧区的新方法.分析了环形热管砂轮在加工中对磨削弧区的强化换热原理,并设计制作出能够用于磨削加工的环形热管砂轮,同时实现了对砂轮基体内环形管腔的密封、抽真空、精确注液与机械式真空封口.最后,在相同磨削工艺条件下,使用环形热管砂轮和无热管砂轮进行TC4钛合金缓进给深切磨削对比试验,验证了环形热管砂轮对磨削弧区温度的控制效果.试验结果表明:设计制作的环形热管砂轮在TC4钛合金高效磨削过程中可以有效降低磨削温度,避免工件表面出现烧伤.     

新型刚玉砂轮磨削GH4169镍基高温合金的性能评价研究

镍基高温合金是航空发动机部件的常用材料,其磨削加工存在工具损耗严重、寿命短等难题。针对3种新研制的刚玉砂轮(分别为粒度60#的微晶和单晶混合磨料砂轮、粒度60#的单晶刚玉砂轮,以及粒度70#的单晶刚玉砂轮),开展了GH4169镍基高温合金材料的磨削试验,从磨削力、磨削温度、砂轮磨损以及表面粗糙度等方面对3种砂轮的磨削性能进行了评价。结果表明,3种砂轮磨削GH4169材料在砂轮磨损和表面粗糙度方面未表现出明显差异,而通过对磨削力和磨削温度的综合评价发现粒度60#的单晶刚玉砂轮的磨削性能更优。3种砂轮磨削GH4169材料的磨削比在0.5~3之间。在正常磨削条件下,3种砂轮的磨削表面粗糙度Ra小于0.4μm。同时发现,砂轮磨损(主要包括磨粒的破碎和脱落)是造成磨削表面缺陷形成的重要原因。     

激光宏观结构化金刚石砂轮磨削氧化铝工艺

为了研究砂轮表面结构化对砂轮磨削性能的影响,利用脉冲激光对树脂结合剂金刚石砂轮进行了表面宏观结构化。采用6种不同类型的金刚石砂轮表面宏观结构进行了氧化铝的磨削实验,建立了激光宏观结构化金刚石砂轮的磨削力模型,比较了6种不同激光宏观结构化金刚石砂轮与非结构化砂轮在不同磨削参数下磨削力的差异,分析了砂轮制造后的表面形貌与结构化砂轮的磨损特性。实验结果表明,砂轮宏观结构化对磨削性能有很大影响,激光宏观结构化砂轮的磨削力可以减小2. 5%~24. 5%,砂轮结构化后的表面形貌出现石墨化现象;宏观结构化砂轮沟槽边缘磨损加剧,但沟槽磨损并没有明显加快宏观结构化砂轮的磨损。     

TC4钛合金材料采用金刚石砂轮磨削时的工艺参数优化

钛合金材料在航空器和发动机中的应用极为广泛,涡扇发动机中低压压气机静子叶片基本由钛合金材料制成,由于钛合金的磨削性能较差,对选用金刚石砂轮进行钛合金材料磨削时的主要工艺影响因素（如进给速度、磨抛深度等）进行了试验分析,优选出更适用于金刚石砂轮磨削钛合金的工艺参数,该参数不仅能够用于自研的双面仿形抛修设备,还可以对其他型号磨床磨削钛合金材料时的工艺参数选择提供指导。     

热管砂轮缓进给深切磨削钛合金试验

分析了热管砂轮在磨削过程中的强化换热原理并研制出可用于磨削加工的热管砂轮,实现了对热管砂轮的抽真空检漏、精确注液以及真空封尾。最后,开展了热管砂轮缓进给深切磨削TC4钛合金的试验研究。试验结果表明,热管砂轮能将磨削弧区积聚的热量通过砂轮内部热管的换热作用快速疏导出去,从而有效降低磨削温度,避免工件烧伤。     

冷滚打渐开线花键滚轮磨削建模研究

根据成形磨削的特点,在分析砂轮形状及其磨损的基础上,选择圆弧形砂轮截面进行冷滚打花键的磨削。磨削时接触点沿砂轮廓形曲线移动,不仅砂轮廓形曲线磨损均匀,而且提高了砂轮的耐用度,减少了砂轮的修整次数。试验结果表明,本文的理论分析、公式推导是正确的,为滚打轮的设计制造提供了理论依据,为其工艺参数的制定和磨床的设计提供了数学指导。     

难加工材料磨削中的砂轮粘附及其抑制措施

分析了磨削中的砂轮粘附情况及其对砂轮磨损的影响 ,提出了抑制砂轮粘附的措施。     

钛合金磨削砂轮表面粘附控制技术

针对钛合金在磨削加工过程中表面粘附的难点,从砂轮材料、加工条件及磨削液的应用等方面具体分析产生这一现象的原因,并提出相应的改进方法。通过试验验证,总结出一套针对钛合金磨削砂轮表面粘附的控制技术。     

磨削烧伤机理及其改善措施的研究

磨削接触区温度过高是引起磨削烧伤的主要因素。本文应用SEM,EPMA、XPS及金相显微分析等技术研究了表面硬化钢和钛合金的烧伤机理。结果表明,有可能采用磨削过程特征参量来监测和预报磨削烧伤的发生。固体润滑剂渗渍涂层砂轮可以改善钛合金的磨削性能。     

Interference and grinding characteristics in ultra-precision grinding of thin-walled complex structural component using a ball-end grinding wheel

As for ultra-precision grinding of difficult-to-process thin-walled complex components with ball-end grinding wheels, interference is easy to occur. According to screw theory and grinding kinematics, a mathematical model is established to investigate the interference and grinding characteristics of the ball-end wheel. The relationship between grinding wheel inclination angle, C axis rotation angle, grinding position angle and grinding wheel wear are analyzed. As the grinding wheel inclination angle increases, the C axis rotatable range decreases and the grinding position angle increases. The grinding position angle and wheel radius wear show a negative correlation with the C axis rotation angle. Therefore, a trajectory planning criteria for increasing grinding speed as much as possible under the premise of avoiding interference is proposed to design the grinding trajectory. Then grinding point distribution on the ball-end wheel is calculated, and the grinding characteristics, grinding speed and maximum undeformed chip thickness, are investigated. Finally, a complex structural component can be ground without interference, and surface roughness and profile accuracy are improved to 40.2 nm and 0.399 μm, compared with 556 nm and 3.427 μm before ultra-precision grinding. The mathematical model can provide theoretical guidance for the analysis of interference and grinding characteristics in complex components grinding to improve its grinding quality.     

Investigation on induction brazing of profiled cBN wheel for grinding of Ti-6Al-4V

Profiled monolayer cBN wheel was induction brazed for grinding of titanium dovetail slot in this study. Aimed at acquiring a uniform temperature distribution along the profiled surface and reducing the thermal deformation of the brazed wheel, a finite element model was established to investigate the temperature uniformity during induction brazing. A suitable induction coil and the related working parameters were designed and chosen based on the simulation results. Ag-Cu-Ti alloy and cBN grains were applied in the induction brazing experiment. The results showed geometric deformation of the brazed wheel was no more than 0.01 mm and chemical reaction layer were found on the brazed joint interface. Further validation tests were carried out by grinding of Ti-6Al-4V alloy. Compared to the electroplated wheel, the brazed wheel showed better performance such as low specific grinding energy and good ground quality in grinding of Ti-6Al-4V alloy. Abrasion wear was found to be the main failure mode for the induction brazed wheel, while adhesion and grains pull-out were the main failure mode for the electroplated wheel.     

Performance evaluation of creep feed grinding of γ-TiAl intermetallics with electroplated diamond wheels

This paper evaluates the performance of creep feed grinding γ-TiAl intermetallic (Ti-45Al-2Mn-2Nb) using electroplated diamond wheels. Firstly, a comparative analysis with the grinding results by using electroplated CBN wheels was conducted, mainly involving abrasive wheel wear behavior and maximum material removal rate below surface burn limit. It was found that the diamond wheel would produce much better grinding results including lower wheel wear rate and higher maximum material removal rate. Then the surface integrity obtained at different level of material removal rate was characterized with the utilization of the diamond wheel. The poor ductility of this γ-TiAl intermetallic material was found to have a marginal effect on the surface integrity, as no severe surface defects such as material pullout were generated during the stable wheel wear stage. For the involved operating parameters, a deformation layer was produced with ∼10 μm or more in thickness depending on the material removal rate used. Meanwhile, a work-hardened layer extending to more than 100 μm was produced with a maximum microhardness of above 520 HV_0.05 (bulk value 360 HV_0.05). The residual stress remained compressive, with a value of above −100 MPa and even up to −500 MPa for an elevated material removal rate. Shearing chip was the main chip type, indicating good wheel sharpness in the grinding process.     

Review on monolayer CBN superabrasive wheels for grinding metallic materials

A state-of-the-art review on monolayer electroplated and brazed cubic boron nitride (CBN) superabrasive wheels for grinding metallic materials has been provided in this article. The fabrication techniques and mechanisms of the monolayer CBN wheels are discussed. Grain distri-bution, wheel dressing, wear behavior, and wheel performance are analyzed in detail. Sample appli-cations of monolayer CBN wheel for grinding steels, titanium alloys, and nickel-based superalloys are also provided. Finally, this article highlights opportunities for further investigation of mono-layer CBN grinding wheels.     

Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function.However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride（CBN） wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temperature, which were better than those of the vitrified one under the same grinding conditions. Compared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.     

镍基高温合金的磨削特征

以GH4169高温合金为主要研究对象,论述了高温合金的磨削特征。由于高温合金的难磨性以及磨削时砂轮表面存在严重的粘附物,因而使磨削力和磨削温度显着增高,磨削比非常低。     

Feasibility study of creep feed grinding of 300M steel with zirconium corundum wheel

The ultrahigh strength 300M steel has been commonly used in the manufacture of aircraft landing gear and rotor shaft parts due to its excellent mechanical properties. Creep feed grinding is one of the essential operations during the whole component manufacturing processes. In this work, the feasibility of creep feed grinding of 300M steel by using the hard zirconium corundum wheel was theoretically and experimentally evaluated. A variety of responses including grinding forces, temperature fields...     

基于数值模拟的内斜齿轮成形磨削 砂轮修形方法

针对内斜齿轮数控成形磨削中较难解决的磨削干涉问题,研究了内斜齿轮成形磨削的砂轮修形方法.在建立内斜齿轮成形磨削数学模型的基础上,用截圆法得到磨削内斜齿轮时砂轮与齿槽接触点所满足的条件方程组,通过牛顿迭代法解此方程组求出砂轮廓形.用数值法模拟出所求砂轮的实际磨削齿形并与理论渐开线齿形作比较,以检验磨削是否干涉及砂轮半径和安装角的选取是否正确.基于 Visual C++ 6.0 编制内斜齿轮砂轮修形及误差分析软件,通过仿真正确选择砂轮安装角、砂轮半径,并输出数控砂轮修整程序.最后通过磨削和检测实例,验证了理论的正确性和软件的可行性.