共查询到20条相似文献,搜索用时 741 毫秒
1.
为了提高铝阳极材料的耐析氢腐蚀和活化性能,用失重腐蚀、电化学等方法研究了在4 mol/LKOH溶液中,丙炔醇对铝阳极(99.999%)电化学性能的影响,结果表明:添加0.5%丙炔醇,不仅使铝的析氢腐蚀速率降低(缓蚀率达85.35%),又能最大程度保持铝阳极的活性(超过铝在4 mol/L KOH溶液中的活性),开路电位Eocp负移达-2.033 V.此外,在"饱和Ca(OH)2+4 mol/L KOH"溶液中,添加0.5%丙炔醇时,铝的缓蚀率高达93.21%,其表面腐蚀均匀,活化性能进一步提高,Eocp负移达-2.011 V.为铝阳极材料的应用提供了有实用价值的添加剂配方. 相似文献
2.
研究了飞机铝合金油箱微生物腐蚀行为及机理。通过对高强铝合金在几种溶液中电化学行为的研究,分析溶液成分对合金耐蚀性的影响。研究发现,航空燃油和水的混合物是微生物腐蚀的必要条件,燃油中所含碳、氮、磷元素是微生物繁衍所需的营养物质,微生物的代谢产物使溶液酸化,增加了溶液的腐蚀性。研究还表明,[H2PO4-]、[HPO42-]和[NO3-]都具有缓蚀和促蚀两方面的作用。 相似文献
3.
采用塔菲尔(Tafel)曲线法和电化学阻抗法(EIS)2种电化学方法评价了 4种不同型号的电子电气缓蚀剂在天然海水中对 T2铜合金、H62铜合金以及 2Al2-T4铝合金的缓蚀效果。对于 T2铜合金,缓蚀剂的缓蚀效率从高至低依次为 DZ-1、TFHS-20、DJB-823、WD-40;对于 H62铜合金,缓蚀效率从高至低依次为 DZ-1、DJB-823、WD-40、 TFHS-20;对于 2Al2-T4铝合金,缓蚀效率从高至低依次为 DZ-1、WD-40、DJB-823、TFHS-20。4种缓蚀剂中,DZ-1缓蚀剂 Tafel曲线法和 EIS法得到的缓蚀效率都高于 99.5%,所以,对于 T2铜合金、H62铜合金以及 2Al2-T4铝合金 3种金属材料来说,DZ-1是 4个型号的缓蚀剂中效果最优的。 相似文献
4.
水溶液中LC4铝合金的微生物腐蚀缓蚀杀菌剂 总被引:1,自引:0,他引:1
通过电化学极化、表面分析等方法,研究了 LC4铝合金在无菌培养液和培养液加硫酸盐还原菌( sulfate-reducing bacteria,简称 SRB)的厌氧体系中加入缓蚀杀菌剂的腐蚀行为。实验结果表明 :SRB能加速LC4铝合金的腐蚀破坏,其腐蚀破坏行为属于点蚀腐蚀机理;加入缓蚀杀菌剂能够影响 SRB的生长规律,抑制 SRB和 Cl-离子对 LC4铝合金的腐蚀破坏。在所研究的 4种缓蚀杀菌剂中,BHA-2缓蚀杀菌剂具有最好的缓蚀和杀菌双重功效,且明显优于市场上广泛使用的 1 2 2 7。 相似文献
5.
采用电化学辅助沉积方法对AZ31B镁合金进行硅烷化处理,借助于动电位极化曲线和电化学阻抗谱等电化学测试手段研究了γ-(甲基丙烯酰氧基)丙基三甲氧基硅烷(KH-570)添加量对膜层质量及耐蚀性能的影响,并比较了利用羟基磷灰石(HA)颗粒、铈盐离子(Ce3+)两种改性物质改良硅烷溶液后所制得膜层的质量及耐蚀性能.结果表明:AZ31B镁合金经电化学辅助沉积硅烷处理后,表面生成一层均匀而致密的硅烷透明膜层,有效地减缓了镁合金的腐蚀行为,促使其自腐蚀电流密度大大降低;在硅烷电化学辅助沉积处理过程中,KH-570存在最佳添加量,当其添加体积约为8 mL时所制备出的硅烷膜层质量最好、耐蚀性能最佳;通过改良硅烷溶液,电化学辅助沉积制备的硅烷膜层质量进一步提高,Ce3+改良效果更佳. 相似文献
6.
《燃气涡轮试验与研究》2021,(3)
采用电化学腐蚀实验方法研究了Ti-6Al-4V(ELI)合金在w(HCl)=3.5%溶液中的电化学阻抗谱,估算了钝化膜厚度;测试了HCl溶液中的极化曲线,得到了相应的腐蚀速率。利用COMSOL Multi-Physics对钛合金/电解质界面建立电化学模型,进行了阻抗的数值模拟及钝化膜厚度的估算。同时,分析了HCl溶液中Ti-6Al-4V(ELI)合金α相和β相的电偶腐蚀机理,预测了β相的腐蚀速率。模拟结果表明:β相的腐蚀电流密度比α相的大,这与以往的腐蚀机理分析结果相符;数值模拟得到的电化学阻抗谱、钝化膜厚度及腐蚀速率与实验测试结果吻合较好。COMSOL数值模拟方法可以用于高效分析合金材料的电化学腐蚀过程及机理。 相似文献
7.
本文介绍了406、406A、D6AC高强钢在几种水性介质中的应力腐蚀试验结果,并对传统使用的0.5%重铬酸钾水溶液和不同浓度硼酸盐溶液缓蚀效果进行了对比分析,提出以四硼酸钠溶液代替重铬酸钾溶液作为高强钢压力容器理想的打压试验介质。 相似文献
8.
镁合金AZ91D在氯化钠溶液中的腐蚀行为 总被引:4,自引:0,他引:4
通过容量法、失重法和电化学阻抗谱(EIS)方法研究了镁合金AZ91D铸件及压铸件在5%氯化钠溶液中的腐蚀及电化学腐蚀行为。利用扫描电子显微镜(SEM)、能量色散谱(EDS)和X-射线衍射(XRD)方法研究了腐蚀产物表面形貌及其组成。结果表明:两种合金的腐蚀产物相同,由块状的化合物氢氧化镁[Mg(OH)2]和松枝状的水合氢氧化镁氯化物[Mg2Cl(OH)3.4H2O]组成;镁合金AZ91D压铸件的耐腐蚀性能比镁合金AZ91D铸件好;并通过浸泡过程中电荷转移电阻(Rt)和双电层电容(Y)的变化解释了两种合金的耐腐蚀性能差异。 相似文献
9.
10.
郭英 《中国民航学院学报》2000,18(3):59-62
研究了聚丙烯酸(PAAC)、苯扎溴铵(DBDAB)在工业纯铁/盐酸体系中的缓蚀性能,推导了一种既能快速测出腐蚀缓蚀剂的缓蚀效率又能确定腐蚀缓蚀剂类型的新方法,定义了能够确定腐蚀缓蚀剂类型因子P。研究结果表明,P〉1.00的缓蚀剂为阳极型的缓蚀剂,P〈1.00的缓蚀剂为阴极型缓蚀剂。 相似文献
11.
12.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
13.
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
14.
15.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
16.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
17.
18.
19.
航天器返回地球的气动特性综述 总被引:4,自引:0,他引:4
航天器返回地球的飞行过程中,气动特性是实现将宇宙飞行速度减到落地前速度、保证再入飞行得到有效控制以及再入防热安全可靠的关键因素。针对简单旋成体气动外形、半弹道式再入控制、烧蚀防热类返回航天器,综述了返回地球过程中变化的空气流域特性、航天器周围的气体绕流环境、空气与航天器作用产生的动力学与热效应等。系统地给出了该类航天器的再入气动特性参数与飞行性能的共性规律,包括:气动阻力与再入减速、气动升力与再入轨迹控制、配平攻角与飞行稳定性、气动加热与防热,以及再入过程中不同气动特性航天器、气象条件变化等对再入飞行性能的影响规律。为航天器开展返回飞行过程的跨流域气动性能工程研制提供设计参考。 相似文献
20.
FU Hong-jun MA Chong-qi KUANG Nai-hang LUAN Shi-lin 《中国航空学报》2007,20(2):124-128
This work was dedicated to performing surface oxidation and coating treatments on carbon fibers (CF) and investigating the changes of fiber surface properties after these treatments, including surface composition, relative volume of functional groups, and sur- face topography with X-ray photoelectron spectroscopy (XPS) and atom force microscopy (AFM) technology. The results show that, after oxidation treatments, interfacial properties between CF and non-polar polyarylacetylene (PAA) resin are remarkably modified by removing weak surface layers and increasing fiber surface roughness. Coating treatment by high char phenolic resin solution after oxida- tion makes interface of CF/PAA composites to be upgraded and the interfacial properties further bettered. 相似文献