共查询到20条相似文献,搜索用时 15 毫秒
1.
文章介绍了一种基本抛物面轴向6i指向-20°、-10°、0°、+10°和+20°的五焦点抛物反射面天线的设计,波束指向分别为-17.2°、-8.67°、0°、8.67°、17.2°。通过优化基本反射面的加权系数进行反射面的赋形,使每个波束的增益趋于均匀。对于标准偏置偏焦抛物面天线,波束指向±17.2°、±8.67°和0°时的增益分别为34.87dBi、38.67dBi和40.15dBi,边缘波束与中心波束的增益差值分别为5.28dBi和1.48dBi。用文中提出的方法得出对应波束的增益分别为36.10dBi、38.48dBi和39.14dBi,边缘波束与中心波束的增益差为3.03dBi和0.66dBi,与标准抛物面相比减小了2.24dBi和0.82dBi。 相似文献
2.
双频多波束天线系统由于收发频段共用同一反射面,覆盖区内收发波束大小不一致.为了实现覆盖区内收发等波束,文章提出了一种新型的台阶反射面天线.通过对天线台阶高度的选取和台阶宽度的优化,可以使接收频率处每个台阶跳跃点与中心区在反射面等效口径处的相位相差180.,从而降低天线的口径效率,减小接收频率处反射面的电尺寸,最终实现了收发波束大小一致.为了进一步降低天线的副瓣电平,文章在接收频率处引入了馈源第一副瓣来照射反射面的台阶圆环,通过这一改进天线仍能实现收发等波束且获得了更低的副瓣电平. 相似文献
3.
多反射面天线系统受空间、位置和尺寸等因素的影响,其主反射面口面存在相位差,从而导致天线辐射性能下降,文章提出了一种利用Zernike多项式赋形多个反射面的方法,通过对副反射面赋形,在主反射面口面得到期望的幅度相位分布。该方法利用Zernike拟合来处理反射面间的光程差,并将主反射面作为固定面,根据几何光学法和光程条件,在Matlab中建立副反射镜初始模型,通过遗传算法优化Zernike系数调整光程差,对副反射镜面形进行优化设计,避免了复杂的微分计算。使用Grasp仿真软件对设计的三反射面天线系统进行了分析,计算表明,与未赋形的三反射面天线相比,赋形反射面天线系统主波束效率提升了10.67%,达到95%以上,验证了该赋形方法的可行性及对天线系统性能提升的有效性。 相似文献
4.
反射面背射螺旋天线设计 总被引:1,自引:0,他引:1
介绍了一种反射面背射螺旋天线,其反射面口径仅有几个波长,通过采用新型背射螺旋天线作馈源,成功解决了小口径反射面天线效率低的难题,实现了高达75%的口面效率。该天线体积小、重量轻,已成功应用于嫦娥一号卫星机械转动定向天线。文章对该天线的设计、仿真计算和实测结果进行了综述。 相似文献
5.
为适应卫星平台的需要,达到卫星天线能够实现角度扫描(正负5度)和机械扫描结构尽可能简单的要求,本文设计了一种三反射镜配置结构的角度扫描天线。首先利用几何光学法设计了赋形面,然后确定了在不同的扫描角度时,平面镜移动到的位置点。最后,利用高斯衍射波束分析方法(Diffraction Guassian Beam Analysis)进行了电性能的仿真验证。结果显示,在所需角度的扫描范围内,其具有较高的主面孔径利用效率和扫描机械结构简单的特点。在兼顾角度扫描和机械扫描结构简单的条件下,天线达到了所需的性能要求。 相似文献
6.
关于双反射面天线的两个优化问题 总被引:1,自引:0,他引:1
在航天器上和地面站中,广泛采用着双反射面天线。本文探讨了双面天线的两个优化问题。当主面为现存的抛物面时,使副面优化赋形,从而比之经典双面(抛物面——双曲面)的增益提高(0.48~0.40)~(dB)(对应于D/λ=20~100)。寻求偏置柱形双反射面系统的最佳设计,使其在馈源方向图变化时,口径场分布最接近同相等幅。 相似文献
7.
8.
9.
为满足星载高增益天线的应用需求,本文设计了一种带有相控阵馈源的伞状可展开反射面天线。首先介绍了反射面天线可展开机构的原理及设计,由碳纤维天线肋和金属编织网面组成反射面,在高精度可展开机构的动作下实现其收拢和展开,从而大幅减小其收藏包络尺寸。对于直径为1.14 m的可展开反射面天线设计了宽带相控阵馈源,采用金属Vivaldi天线作为相控阵单元,根据极化方式、焦径比和扫描范围选择排列成双极化矩形阵列,使可展开反射面天线在8~16 GHz内实现二维波束扫描,通过电磁仿真进行验证,仿真结果表明,宽带相控阵馈源能够有效地增加可展开反射面天线的视场,反射面天线在8 GHz、12 GHz和16 GHz时扫描到0°的增益分别是38.03 dB、40.65 dB和41.48 dB,扫描到+3°的增益分别是37.68 dB、40.68 dB和41.09 dB。 相似文献
10.
该设计结合科研实际需求,研制了工作在C频段的“推扫式”卫星扫描天线。首先,从“推扫式”卫星扫描天线的原理出发,对所需要的环焦反射面进行了优化建模,提出一种新型扇形反射面圆角化的方案,并针对密集馈源阵进行分析。通过计算得到了馈源的位置坐标,在仿真软件GRASP中构造反射面天线的整体模型。为了使密集馈源阵的主波束满足设计指标,设计了遗传算法优化合成后的波束来实现对主波束的优化,通过改变馈源阵的幅相值以达到天线方向图的设计要求,利用仿真优化得到了C频段中心波束达到设计指标所需要的馈源阵规模。最后,对整体模型进行了加工组装。使用近场测量的方法在微波暗室中对天线进行测试,测试结果表明天线波束宽度为0.6°时,主波束效率为98.17%,大于98%,满足设计要求。 相似文献
11.
This paper deals with the initial shape analysis, cutting-pattern analysis, surface accuracy measurement and modal testing of high-precision inflatable antennas reflectors that are intended for spaceflight applications. The initial shape analysis method, formulated on the basis of membrane theory and elastic mechanics, determines the required as-manufactured shape of the reflective surface of the antenna reflector. On the other hand, the cutting-pattern analysis method, with its formulation based on spring-mass representations, numerically calculates the required cutting pattern of the planar membrane gores that are to be assembled to form the 3-dimensional reflective surface. To validate the effectiveness of the proposed analysis methods, a 3.2-m antenna reflector model was designed, manufactured, and assembled for ground demonstration and testing. The reflective surface accuracy of this demonstration reflector model was measured by a photogrammetric measuring system. Shape adjustments of the reflective surface were performed by systematically adjusting the tension in the cables that were used to mount the reflector to its support structure. It was found that the reflective surface accuracy of the reflector model, as defined by its RMS error from a best-fit parabolic shape, was less than 1 mm. In addition, dynamic and RF tests were also performed on the demonstration reflector model. The test results indicated that the first-mode frequency of the reflector model agreed well with the corresponding analytical prediction, and its radiation pattern was also well focused. 相似文献
12.
Surface accuracy analysis of large deployable antennas 总被引:1,自引:0,他引:1
This paper performs an analysis to the systematic surface figure error influenced by three factors including errors of faceted paraboloids, fabrication imperfection and random thermal strains in orbit. Firstly, the computational formulas for root-mean-square surface deviations caused by these factors are presented respectively. The stochastic finite element method is applied to derive the computational formulas of fabrication imperfection and random thermal strains, by which the sensitivity of surface accuracy to component imperfection can be revealed. Then the Monte Carlo simulation method is introduced to obtain the surface figure by sampling test on random errors. Finally, the analytical method is applied to the research on the surface figure error of AstroMesh deployable reflector. The results show that the deviations between the root-mean-square surface errors calculated by the proposed formulas with less consuming time and those by the Monte Carlo simulation method are less than 2%, which indicates that the proposed method is efficient and receivable enough to analyze systematic surface figure error of a large deployable antenna. Moreover, further investigations on the relationship between surface RMS deviation and the antenna parameters including aperture and the number of subdivisions are presented in the end. 相似文献
13.
14.
为探究反射面天线形变对风云卫星毫米波和亚毫米波成像仪(MMSI)的亮温图像质量的影响,运用基于表面电流积分的物理光学方法计算天线辐射方向图,探究不同形式反射面天线形变下天线辐射特性的变化规律。结合MMSI的亮温图像的处理结果,评价图像质量的变化。实验结果表明:反射面天线的形变面积、形变位置和副反射面晃动发生变化时,天线的主瓣增益、副瓣电平和波束宽度等关键指标发生规律性变化,对MMSI的亮温图像质量产生不同形式的影响。当反射面天线的形变面积增大时,天线的主瓣增益减小,副瓣电平升高,进一步导致分辨率降低,噪声水平升高,亮温图像质量变差。 相似文献
15.
天线反射器型面精度是衡量、评价天线质量的重要指标之一,天线型面精度的高低将直接影响天线的电性能指标。大型环形可展开天线型面精度测试,目前多采用高精度工业数字化摄影测量技术进行,在使用高精度数字化摄影测量系统对大型环形可展开天线开展型面测试过程中,系统测量精度主要受摄影基准选用、测量距离、测量靶标大小、测量角度、测量拍照数量、相机参数等多项工艺参数影响。就如何使用数字化摄影测量系统对大型环形可展开天线开展高精度型面测试方法开展研究,通过对高精度长基准尺的设计及布局研究,以及对摄影测量系统最优匹配工艺参数研究及验证,得到一种针对大型环形可展开天线开展高精度型面测试的方法。试验证明,该方法可靠有效,能够满足大型环形可展开天线开展型面高精度测试的测量需求。 相似文献
16.
为验证镜像综合孔径微波辐射成像的原理,设计了V波段镜像综合孔径辐射成像原理实验系统(MAS-V),介绍了系统组成及原理并进行了电暖器辐射成像及空间分辨率实验,电暖器热辐射部分清晰可见,且轮廓与光学图像结果一致。实验结果表明:镜像综合孔径微波辐射成像的原理正确。对于相同的天线阵列,镜像综合孔径的空间分辨率优于常规综合孔径,约为其2倍。若增大反射板与天线阵列的距离,镜像综合孔径的空间分辨率将进一步提高。研究结果为镜像综合孔径微波辐射成像方法应用于静止轨道大气遥感提供了参考。 相似文献
17.
为了满足大功率反射面天线的馈源设计要求,文章设计了一种大功率圆极化交叉对称阵子天线,其工作频率在1.19GHz~1.285GHz,天线整体由交叉对称阵子和开槽线巴伦组成。通过开槽线巴伦实现平衡-非平衡馈电。为了实现圆极化,通过改变对称阵子结构,在对称阵子臂相邻90°处增添一对阵子臂,形成交叉对称阵子,并通过调整阵子臂的长度,使其实现90°自相移结构,并最终实现圆极化,由于天线整体均为金属,使得天线可以承受更高的功率。该天线在119GHz~1285GHz频带内电压驻波比(votage standing wave ratio,VSWR)<1.5,圆极化轴比<3dB,实测结果表明,实测和仿真结果基本一致,天线在该频段内实现了较好的圆极化特性。 相似文献
18.
The woven fabric membrane materials are widely used in space and terrestrial inflatable reflectors. However the material?s anisotropy makes the design analysis more complex. The deviation from the desired shape, so-called “W-profile error”, influences the precision of the membrane surface significantly. In this study, a model of an axisymmetric paraboloid surface using membrane theory is established for the purpose of facilitating the surface precision optimization. Analytical solutions for displacements of the reflector are derived. An iteration method of initial reflector profile solution is stated and a finite element (FE) software employed in the solution is presented. A case study is illustrated to make a comparison between numerical and theoretical analyses. Finally, the conclusions are drawn that the analytical method and the FE iterative method for initial profile solution are feasible and efficient. 相似文献
19.