微细电解加工系统设计及实验研究

针对微细电解加工的特殊工艺要求研制了微细电解加工系统,包括机床本体及配套的电气控制系统,采取直接进给加工和周期循环加工两种不同的运动控制方案进行微细孔电解加工试验,并对结果进行比较分析。     

超薄扭曲叶片精密电解加工

介绍了由方料经单面电解加工超薄扭曲叶片叶身型面的方法．以及其零件加工难点、夹具和阴极结构及非加工面的保护．用该方法批生产叶片、叶身型面重复制造精度稳定，型面轮廓精度基本满足了无余量修抛要求．     

基于电解扫掠成形原理的整体叶盘叶根加工方法

采用片状或管状阴极电解加工(ECM)后的整体叶盘由于加工运动、阴极形状等原因在叶根处会形成一定的加工残留,影响整体叶盘的加工精度。针对叶片电解加工后形成的叶根残留,开展去除叶根残留电解加工方法的研究,解决叶根电解加工的阴极结构、加工路径设计等难题。首先,分析了叶根的残留分布情况以及叶间通道的结构,采用了电解扫掠成形加工方案。其次,设计了阴极结构与加工路径,在阴极结构上采用了扇形流道并分析了电解液流速分布,通过增加引流槽、改变倾角等措施改善了流场;对阴极的运动路径进行了规划,利用专用仿真软件对阴极运动干涉与加工程序进行了检验;通过附加叶盘转动补偿了由于不同截面内叶间通道宽度与阴极刃口尺寸不一致给加工带来的不足。最后,制作了电解加工装置并通过试验对叶根电解加工方法进行了验证。试验结果表明,该加工方法有效去除了叶根残留,加工表面质量好,加工精度达到了要求。     

整体叶盘电解加工电解液进液角度优化研究

整体叶盘电解加工中,流场对加工稳定性起着重要作用,电解液进液角度对流场均匀性具有重要影响。针对由叶尖至叶根流动模式,设计了5种电解液进液角度流动模型（12°、22°、32°、42°以及52°）,并开展电解加工流场仿真研究。结果表明,电解液进液角度为32°时,平均流速为19.01 m/s,流速均方差为6.33,满足整体叶盘电解加工对流场的要求。在电解液进液角度为32°的流场形式下,开展整体叶盘电解加工试验,加工过程稳定,试件表面无流纹,加工精度为0.12 mm,表面粗糙度为Ra0.353μm,验证了流场的合理性。     

大直径整体叶轮分步法电解加工工艺与试验

在对大直径整体叶轮的叶片特征和过去电解加工(ECM)方法比较分析的基础上提出了一种叶片分步加工的电解加工方法.首先确立了分步法的加工顺序,采用专用仿真软件对叶片的被加工区域进行划分,使前道工序加工后留下的区域满足后道工序的电解加工要求;在此基础上计算各工序的加工运动路径,并根据机床运动配置形式给出了叶片加工所需的四轴联动算法,通过软件自动生成数控加工自动编程;借助于CAD/CAE/CAM软件设计了一组加工阴极并进行了工艺试验.试验结果表明,通过合理的区域划分,叶盆、叶背和叶根的加工过程具有较好的稳定性,叶背、叶根的加工精度得到了较好的控制.该工艺方法可望较高精度地解决大直径整体叶轮叶片型面加工难题.     

定间隙间歇送进-混气电解加工技术

介绍了定间隙间歇送进-混气电解加工技术及其提高复制精度的途径,通过试验研究了该技术在提高电解加工精度及表面质量方面的优越性。     

内喷式阴极电解加工整体叶轮叶间通道的间隙特性

本文介绍了在内喷式阴极展成电解加工整体叶轮叶间通道时，加工电压、阴极进给速度、电解液压力和温度对加工间隙的影响，经过对其试验数据所作分析，得出了一些有益的结论，为展成电解加工整体叶轮提供了试验与理论依据。     

异形型腔电解加工阴极的数字化设计

建立了异形型腔电解加工阴极设计和加工过程仿真的数学物理模型,并在MATLAB平台上利用PDETool工具箱编制了有限元求解和动态加工仿真程序,针对某型发动机扩压器叶间流道异形型腔设计制造了阴极和工装夹具,选择并优化了加工参数,试验加工出的型腔试件能均匀留出0.15～0.30 mm的加工余量,满足了实际加工的工序要求.     

基于超纯水电解加工的水解离机理研究

介绍了一种以超纯水为电解液的电解加工工艺方法,即超纯水电解加工技术.研究了阳离子交换膜在超纯水中的水解离机理及工作特性,分析其在超纯水电解加工过程中的作用机理,并进行了水解离试验研究.结果表明：电流密度达到了3.7 A/cm^2,电场强度约为2 MV/m,已进入微细电解加工去除材料要求范围,为超纯水微细电解加工的应用奠定了基础.     

精密电解套料阴极设计与优化

通过对整体叶盘的结构特点、技术要求和材料特性等分析,确定了电解加工技术方案,分析了电解加工套料阴极设计及轨迹计算、成型阴极设计、参数优化等3大关键技术,重点针对套料加工阴极型面设计、流场设计、轨迹计算、间隙计算等关键步骤进行了详细论述,并通过试验进一步反复优化,解决了流场不均、火花短路等问题,最终验证了工艺可行性,且套料电解加工的叶盘余量较为均匀,能够满足后续精电解加工要求,取得了良好效果.     

ν-gap度量及其在飞行控制律评估中的应用

 传统控制律评估方法主要用于单输入单输出（SISO）系统，且对模型参数摄动考虑不够全面,针对这些不足，研究了ν-gap度量方法。在介绍系统广义稳定裕度相关概念的基础上，给出了ν-gap度量的定义、特点和性质以及近似摄动模型的计算，提出ν-gap度量评估控制律的步骤。实例结果表明，该方法不仅克服了上述传统评估方法的缺陷，而且还有根据所求的各摄动影响情况忽略影响小的元素，以减少计算量及可以找到最坏情况下的参数摄动组合等优点。     

Integrated Entry Guidance for Reusable Launch Vehicle

A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method.     

基于飞机油箱模型形状特征油量测量切片步长选择方法研究

 在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明：该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

二维翼段颤振的μ控制

 采用超声电机作为作动器来实现含控制面的翼段颤振鲁棒抑制。针对作者设计的二维翼段颤振主动抑制系统，通过理论与实验相结合的方法，建立了考虑沉浮方向阻尼和作动器模型参数不确定性的控制系统模型，设计了μ控制器，并对控制器做了降阶处理。数值仿真和风洞试验表明，μ控制器可有效地抑制颤振的发生，将颤振临界速度提高23.4%。相对于H_∞控制器，μ控制器的控制效果和鲁棒性更好。     

航空发动机管路测量数据分割方法

 为了提高航空发动机管路测量数据的反求建模效率,提出了一种区域增长分割算法。该方法主要是利用管路表面在曲面索引系数映射、主曲率映射、高斯映射上的特性,并基于均值漂移算法和遗传算法提出了区域分割算法中种子区域的选择策略。然后利用区域增长分割方法实现了对管路测量数据的分割。经过仿真和实测数据验证,所提管路分割算法具有较好的分割质量和效率。     

Abnormal Shape Mould Winding

为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。     

Interfacial Properties Modification of Carbon Fiber/ Polyarylacetylene Composites

This work was dedicated to performing surface oxidation and coating treatments on carbon fibers (CF) and investigating the changes of fiber surface properties after these treatments, including surface composition, relative volume of functional groups, and sur- face topography with X-ray photoelectron spectroscopy (XPS) and atom force microscopy (AFM) technology. The results show that, after oxidation treatments, interfacial properties between CF and non-polar polyarylacetylene (PAA) resin are remarkably modified by removing weak surface layers and increasing fiber surface roughness. Coating treatment by high char phenolic resin solution after oxida- tion makes interface of CF/PAA composites to be upgraded and the interfacial properties further bettered.     

Thermal Stresses and Cracks During the Growth of Large-sized Sapphire with SAPMAC Method

本文利用有限元法对冷心放肩微量提拉法(SAPMAC)生长大尺寸蓝宝石单晶过程中的热应力进行了模拟计算,应用临界缺陷理论解释了裂纹的萌生与扩展机理。研究表明,晶体内的热应力主要与晶体生长速率,环境温度和结晶取向有关;较大热应力多出现在结晶界面,放肩、收尾以及直径急剧变化等位置;最大热应力总是出现在籽晶与新生晶体的界面附近。裂纹将在临界缺陷位置产生,并在应力作用下沿a或m面扩展。计算结果与实验结果基本吻合,通过晶体生长系统和生长工艺的改进,对晶体的开裂问题得到了有效的抑制。     

Optimization Design System for Composite Structures Based on Grid Technology

To solve the topology optimization of complicated multi-objective continuous/discrete design variables in aircmit structure design, a Parallel Pareto Genetic Algorithm （PPGA） is presented based on grid platform in this paper. In the algorithm, the commercial finite element analysis （FEA） software is integrated as the calculating tool for analyzing the objective functions and the filter of Pareto solution set based on weight information is introduced to deal with the relationships among all objectives. Grid technology is utilized in PPGA to realize the distributed computations and the user interface is developed to realize the job submission and job management locally/remotely. Taking the aero-elastic tailoring of a composite wing for optimization as an example, a set of Pareto solutions are obtained for the decision-maker. The numerical results show that the aileron reversal problem can be solved by adding the limited skin weight in this system. The algorithm can be used to solve complicated topology optimization for composite structures in engineering and the computation efficiency can be improved greatly by using the grid platform that aggregates numerous idle resources.