发动机试验液氢流量测量不确定度评定

针对某型号液体火箭发动机试验,介绍了液氢低温流量测量系统组成及原理。根据液氢质量流量测量数学模型,分析影响液氢流量测量不确定度的主要压力对贮箱容积的影响因素,依据不确定度评定相关标准和方法,对各种影响因素进行分析,最终得出液氢质量流量扩展不确定度为±0.88%,满足发动机设计部门对液氢低温质量流量测量不确定度±1%的要求。     

Single crystal mo solar thermal thruster for microsatellites

One potentially attractive propulsion concept offering significant payload gains for orbit transfer from LEO to higher orbits, station keeping and attitude control of spacecraft is thermal propulsion using light gas (typically hydrogen) as propellant and various kinds of heat energy. Solar Thermal Propulsion (STP) is a typical thermal propulsion with high Isp (500 – 1,000 s) in an appropriate thrust magnitude range and provides possibly much less space pollution than conventional chemical propulsion.

This paper presents the test results of a 30 mm dia. (medium-sized) windowless type of single crystal Mo thruster for orbit transfer of 50 kg class microsatellites. The cavity dia. is 20 mm, double the size of the previous model, and can apply to a primary solar reflector of up to 3.5 m dia., which is the maximum size containable in the H-II rocket fairing without segmentation. The performed mission analyses indicate that this size of STP is suitable to orbit transfer of 50 kg class microsatellites, such as LEO to GEO, or only multiple apogee kicks from GTO to GEO or deep space missions.     

Nanosatellites and micro systems technology — capabilities, limitations and applications

In recent years Micro Systems Technology (MST) was introduced to manufacture miniaturized components for satellite subsystems, like small sensors, valves, micromotors, antennas and many more. These components can be used to build a new class of satellites weighing considerably less than 10 kg, with the capabilities comparable to present microsatellites. With the possibility of cheap mass production of such nanosatellites new applications become possible. However, the construction of very small satellites is connected with problems concerning launch, orbit control and, deorbiting. Furthermore the reduction of size creates certain limits for power consumption, data rates and optical resolutions which have to be carefully considered.     

失效航天器姿态接管的SDRE微分博弈控制

针对燃料耗尽的失效航天器姿态接管控制问题，提出多颗微卫星协同实现姿态稳定的状态相关黎卡提方程(SDRE)微分博弈控制方法。首先，将姿态接管问题转化为多颗微卫星的微分博弈问题，基于组合航天器的姿态模型和微卫星的性能指标函数建立多颗微卫星的非线性微分博弈模型，微卫星通过独立优化各自的性能指标函数得到控制策略。其次，引入状态相关系数矩阵，将非线性博弈转化为状态相关线性二次型博弈，采用SDRE方法更方便地逼近微卫星的博弈均衡策略。最终通过李雅普诺夫迭代法求解耦合状态相关黎卡提方程组得到微卫星的状态反馈控制器，实现微卫星的自主决策。数值仿真验证了多颗微卫星采用微分博弈控制方法实现姿态接管的有效性和容错性。     

Advanced materials for space applications

Since NASA was created in 1958, over 6400 patents have been issued to the agency—nearly one in a thousand of all patents ever issued in the United States. A large number of these inventions have focused on new materials that have made space travel and exploration of the moon, Mars, and the outer planets possible. In the last few years, the materials developed by NASA Langley Research Center embody breakthroughs in performance and properties that will enable great achievements in space. The examples discussed below offer significant advantages for use in small satellites, i.e., those with payloads under a metric ton. These include patented products such as LaRC SI, LaRC RP 46, LaRC RP 50, PETI-5, TEEK, PETI-330, LaRC CP, TOR-LM and LaRC LCR (patent pending). These and other new advances in nanotechnology engineering, self-assembling nanostructures and multifunctional aerospace materials are presented and discussed below, and applications with significant technological and commercial advantages are proposed.     

The hydrogen value chain: applying the automotive role model of the hydrogen economy in the aerospace sector to increase performance and reduce costs

Hydrogen will assume a key role in Europe's effort to adopt its energy dependent society to satisfy its needs without releasing vast amounts of greenhouse gases. The paradigm shift is so paramount that one speaks of the “Hydrogen Economy”, as the energy in this new and ecological type of economy is to be distributed by hydrogen. However, H₂ is not a primary energy source but rather an energy carrier, a means of storing, transporting and distributing energy, which has to be generated by other means.Various H₂ storage methods are possible; however industries' favourite is the storage of gaseous hydrogen in high pressure tanks. The biggest promoter of this storage methodology is the automotive industry, which is currently preparing for the generation change from the fossil fuel internal combustion engines to hydrogen based fuel cells. The current roadmaps foresee a market roll-out by 2015, when the hydrogen supply infrastructure is expected to have reached a critical mass. The hydrogen economy is about to take off as being demonstrated by various national mobility strategies, which foresee several millions of electric cars driving on the road in 2020.Fuel cell cars are only one type of “electric car”, battery electric as well as hybrid cars – all featuring electric drive trains – are the others. Which type of technology is chosen for a specific application depends primarily on the involved energy storage and power requirements. These considerations are very similar to the ones in the aerospace sector, which had introduced the fuel cell already in the 1960s. The automotive sector followed only recently, but has succeeded in moving forward the technology to a level, where the aerospace sector is starting considering to spin-in terrestrial hydrogen technologies into its technology portfolio. Target areas are again high power/high energy applications like aviation, manned spaceflight and exploration missions, as well as future generation high power telecommunication satellites. Similar trends can be expected in the future for RADAR Earth Observation satellites and space infrastructure concepts of great scale.This paper examines current activities along the hydrogen value chain, both in the terrestrial and the aerospace sector. A general assessment of the synergy potential is complemented by a thorough analysis of specific applications serving as role models like a lunar manned base or pressurised rover, an aircraft APU or a high power telecommunications satellite. Potential performance improvements and cost savings serve as key performance indicators in these comparisons and trade-offs.     

Use of Optical Characteristics to Identify Orbiting Material

Knowledge of the observable properties of orbital debris is necessary to validate debris models for both the low Earth orbit (LEO) and the geosynchronous Earth orbit (GEO). Current methods determine the size and mass of orbital debris based on knowledge or assumption of the material type of the piece. Improvement in the knowledge of material is the goal of the research described herein. The process of using spectral absorption features to determine the material type is explored. A review of the optical measurements of orbital debris as well as current research in the area is discussed. Reflectances of common spacecraft materials are compared. The need for, and advances made possible by obtaining real data are explored. The prospects of the venture are investigated.     

The use of the Earth’s gravitational potential for interplanetary flights

An efficient scheme of the use of the Earth’s gravity in interplanetary flights is suggested, which opens up new opportunities for exploration of the solar system. The scheme of the gravitational maneuver allows one to considerably reduce the spacecraft mass consumption for a flight and the time of flight. An algorithm of the gravitational maneuver is suggested that takes into account the restriction on the altitude of a planet flyby. Estimates are made of transport capabilities for delivery of a spacecraft to the orbits of Jupiter, Saturn, and Uranus. The spacecraft is based on a middle-class carrier launcher of the Soyuz type and includes chemical and electric plasma jet engines of the SPD-140 type, which use solar energy.     

Measurement of the Quasistatic Component of Microaccelerations Using a Convection Sensor onboard a Satellite

The problem of the interpretation of measurements made by means of a convection sensor is considered. The sensor is a cubic chamber filled by a viscous fluid (gas). Fixed and unequal temperatures are maintained on two opposite sides of the cube; the other sides are perfect heat conductors. Two differential thermocouples are placed inside the chamber to measure the temperature difference at two pairs of fixed points. The sensor is mounted aboard the Earth's satellite. Mathematical models of various degrees of complexity are proposed which describe processes of heat and mass transfer under the action of a quasistatic component of microaccelerations. The results of mathematical simulation of the data of sensor thermocouples presenting a response to the real quasistatic component of microaccelerations which took place aboard the Mirstation are given. It is shown that under usual conditions of an orbital mission the sensor presents a linear low-frequency filter. By combining the data of several identical sensors, tightly arranged and oriented in a certain way, it is possible to measure low-frequency components of the angular acceleration of the satellite and linear microaccelerations at the point of the sensor position.     

Multiobjective optimization applied to structural sizing of low cost university-class microsatellite projects

In recent years, there has been continuing interest in the participation of university research groups in space technology studies by means of their own microsatellites. The involvement in such projects has some inherent challenges, such as limited budget and facilities. Also, due to the fact that the main objective of these projects is for educational purposes, usually there are uncertainties regarding their in orbit mission and scientific payloads at the early phases of the project. On the other hand, there are predetermined limitations for their mass and volume budgets owing to the fact that most of them are launched as an auxiliary payload in which the launch cost is reduced considerably. The satellite structure subsystem is the one which is most affected by the launcher constraints. This can affect different aspects, including dimensions, strength and frequency requirements. In this paper, the main focus is on developing a structural design sizing tool containing not only the primary structures properties as variables but also the system level variables such as payload mass budget and satellite total mass and dimensions. This approach enables the design team to obtain better insight into the design in an extended design envelope. The structural design sizing tool is based on analytical structural design formulas and appropriate assumptions including both static and dynamic models of the satellite. Finally, a Genetic Algorithm (GA) multiobjective optimization is applied to the design space. The result is a Pareto-optimal based on two objectives, minimum satellite total mass and maximum payload mass budget, which gives a useful insight to the design team at the early phases of the design.     

Radiation engineering analysis of shielding materials to assess their ability to protect astronauts in deep space from energetic particle radiation

An analysis is performed on four typical materials (aluminum, liquid hydrogen, polyethylene, and water) to assess their impact on the length of time an astronaut can stay in deep space and not exceed a design basis radiation exposure of 150 mSv. A large number of heavy lift launches of pure shielding mass are needed to enable long duration, deep space missions to keep astronauts at or below the exposure value with shielding provided by the vehicle. Therefore, vehicle mass using the assumptions in the paper cannot be the sole shielding mechanism for long duration, deep space missions. As an example, to enable the Mars Design Reference Mission 5.0 with a 400 day transit to and from Mars, not including the 500 day stay on the surface, a minimum of 24 heavy lift launches of polyethylene at 89,375 lbm (40.54 tonnes) each are needed for the 1977 galactic cosmic ray environment. With the assumptions used in this paper, a single heavy lift launch of water or polyethylene can protect astronauts for a 130 day mission before exceeding the exposure value. Liquid hydrogen can only protect the astronauts for 160 days. Even a single launch of pure shielding material cannot protect an astronaut in deep space for more than 180 days using the assumptions adopted in the analysis. It is shown that liquid hydrogen is not the best shielding material for the same mass as polyethylene for missions that last longer than 225 days.     

Superconducting magnets and mission strategies for protection from ionizing radiation in interplanetary manned missions and interplanetary habitats

First order evaluations for active shielding based on superconducting magnetic lenses were made in the past in ESA supported studies. The present increasing interest of permanent space complexes, to be considered in the far future as ‘bases’ rather than ‘stations’, located in ‘deep’ space (as it has been proposed for the L1 libration’s point between Earth and Moon, or for Stations in orbit around Mars), requires that this preliminary activity continues, envisaging the problem of the protection from cosmic ray (CR) action at a scale allowing long permanence in ‘deep’ space, not only for a relatively small number of dedicated astronauts but also to citizens conducting there ‘normal’ activities.Part of the personnel of such a ‘deep space base’ should stay and work there for a long period of time. It is proposed that the activities and life of these personnel will be concentrated in a sector protected from Galactic CR (GCR) during the whole duration of their mission. In the exceptional case of an intense flux of Solar Energetic Protons (SEP), this sector could be of use as a shelter for all the other personnel normally located in other sectors of the Space Base.The realization of the magnetic protection of the long permanence sector by well-established current materials and techniques is in principle possible, but not workable in practice for the huge required mass of the superconductor, the too low operating temperature (10–15 K) and the corresponding required cooling power and thermal shielding.However the fast progress in the production of reliable High Temperature Superconducting (HTS) or MgB₂ cables and of cryocoolers suitable for space operation opens the perspective of practicable solutions. In fact these cables, when used at relatively low temperature, but in any case higher than for NbTi and Nb₃Sn, show a thermodynamically much better behavior. Quantitative evaluations for the protection of the sector of the ‘Space Base’ to be protected from GCRs (and therefore from SEPs also) are presented.For possible large outer radius solutions it must in the meantime solve the problem of the assembling or deploying in space the conductors for returning the electric current.     

Estimation of dynamic characteristics of the <Emphasis Type="Italic">International Space Station</Emphasis> from measurements of microaccelerations

We describe the results of determining the mass of the International Space Station using the data of MAMS accelerometer taken during correction of the station orbit on August 20, 2004. The correction was made by approach and attitude control engines (ACE) of the Progress transporting spacecraft. The engines were preliminary calibrated in an autonomous flight using the onboard device for measuring apparent velocity increment. The method of calibration is described and its results are presented. The error in station mass determination is about 1%. The same data of MAMS and similar data obtained during the orbit correction on August 26, 2004 were used for the analysis of high-frequency vibrations of the station mainframe caused by operation of the ACE of Progress. Natural frequencies of the ACE are determined. They lie in the frequency band 0.024–0.11 Hz. ACE operation is demonstrated to result in a substantial increase of microaccelerations onboard the station in the frequency range 0–1 Hz. The frequencies are indicated at which disturbances increase by more than an order of magnitude. The study described was carried out as a part of the Tensor technological experiment.     

Analysis of heterogeneous recombination of oxygen atoms on aluminum oxide by methods of quantum mechanics and classical dynamics

To analyze the catalytic properties of heat shield materials of space vehicles, the cluster models of the adsorption of oxygen atoms on aluminum oxide are constructed and the corresponding potential energy surface is calculated on the basis of the density functional theory. Quantum-mechanical calculations showed that it is necessary to take into account the relaxation of the surface monolayers. Using this surface in molecular dynamics, calculations made it possible to obtain the probabilities of the heterogeneous recombination of oxygen atoms on the α-Al₂O₃ surface, which are in good agreement with experimental data. The calculations performed substantially decrease the amount of experimental investigations necessary reliably to describe the heterogeneous catalysis on promising reusable heat shield coatings for analyzing heat transfer during spacecraft entry into the atmosphere.     

舱外航天服冷热电一体化系统性能分析

文章提出了一种舱外航天服冷热电一体化(Combined Cooling-Heating-Power,CCHP)系统,该系统的主要组件有质子交换膜燃料电池、热驱制冷装置、金属氢化物储氢装置和辐射器等.在冷热电一体化系统的冷电匹配方法上提出了“以电定冷”方案,按照该方案计算了一组典型工况下系统的工作状态,分析了燃料电池的工作温度、工作电流密度和工作压力对系统质量和消耗性工质损失的影响.结果表明,该舱外航天服冷热电一体化系统在质量大小方面可以接受,在消耗性工质损失方面比水升华器冷源/蓄电池电源方案小得多;且降低燃料电池工作温度和压力、增大燃料电池工作电流密度,均能够减小系统质量、降低系统消耗性工质损失.     

Structure of current and plasma in current sheets depending on the conditions of sheet formation

The structure of current sheets created under laboratory conditions is characterized by a large variety, which depends substantially on the conditions under which the sheet if formed. In this work, we present the results of an experimental study of the structure and evolution of current sheets that were formed in magnetic configurations with a singular line of the X type. It has been shown that the change in the transverse magnetic field gradient, the strength of the longitudinal magnetic field, and the mass of the ions in plasma makes it possible to significantly vary the main parameters of the current sheets. This offers the challenges of using laboratory experimental results for analyzing and simulating the cosmophysical processes.     

航空航天用纳米碳复合材料研究进展

对航空航天用纳米碳复合材料及其多功能特性的研究进展情况进行了综述，阐述了国内外研究者们在纳米碳复合材料及其多功能特性方面取得的重要成果，并系统地综述了纳米碳复合材料在多尺度增强、电磁屏蔽、智能驱动、隔热、传感方面的研究工作。最后展望了纳米碳复合材料在航空航天领域中的潜在应用。     

气-气喷嘴结构分析

对以气氢/气氧为推进剂的同轴剪切、离心和同轴双剪切结构的喷嘴进行设计,分析了这三种结构型式的喷嘴结构尺寸;通过对同轴剪切式和同轴双剪切喷嘴燃烧室流场进行数值模拟,研究喷嘴流量和结构对推进剂燃烧过程的影响。研究结果认为：同轴剪切式喷嘴结构简单;离心式喷嘴的流量系数小且带有旋流室,导致喷嘴的结构尺寸大;同轴双剪切喷嘴使推进剂在燃烧室内形成两个燃烧面,能在大流量下使推进剂达到高的燃烧效率。     

Asteroidal resources for space manufacturing

Earth-approaching asteroids (Apollos and Amors) may be competitive candidates as raw materials for space manufacturing. The total energy per unit mass required to transfer material from some of these bodies to high Earth orbit is comparable to that for lunar material. Recent optical studies suggest ordinary and carbonaceous chondrite compositions for these asteroids, with some containing large quantities of metallic iron and nickel, and others, carbon, hydrogen and nitrogen. Discoveries of several new candidate asteroids over the next few years will allow for a better selection of materials and mission possibilities. Material from one of these asteroids, either in raw or manufactured form, could be returned to the vicinity of the Earth by a solar-powered mass-driver reaction engine. With a requirement of ～60 shuttle flights, and with minimal development costs, an automated mission to a 200-m dia. (10⁷ ton) metal-rich asteroid could be carried out by a mass-driver tug assembled in low Earth orbit using shuttle tankage as reaction mass. Such a tug could, within a few years, move the asteroid into high Earth orbit for the manufacturing of ～ 20 satellite power stations using a portion of the asteroid itself as reaction mass. In the next few years over 100 asteroids in this size range could be discovered, orbits determined and composition types classified using existing earthbased and spaceborne search techniques.     

金属材料表层氢的相对测定

金属材料表层氢的测定是一个难点。依据表层氢的释放特点,在RH600型氢测定仪上建立了表层氢的相对测定方法。该方法采用逐步提高电极炉加热功率的方式,测定并记录材料释放的表层氢,为生产中如材料的表层吸氢问题,提供直接数据依据。