RTM 用R801 树脂工艺及性能

对一种新型RTM用双马来酰亚胺树脂R801的固化反应特性、成型工艺及其制备的复合材料性能进行了研究,DSC曲线表明该树脂体系的固化温度为170～220℃;黏度随温度变化曲线表明在70～120℃,树脂黏度增长缓慢,具有不少于7 h的适用期;在90℃左右时,其初始黏度<100 mPa.s,工艺操作窗口时间≥10 h;该树脂制备的MT300碳纤维复合材料在300℃时的压缩、弯曲、层剪性能保持率均≥63%。     

RTM用炔基改性苯并噁嗪树脂工艺及力学性能

文摘为改善苯并噁嗪树脂对树脂传递模塑(RTM)成型工艺的适应性,并进一步提升苯丙噁嗪基复合材料的耐高温性能。提出利用炔基改性苯并噁嗪树脂,以提高树脂的交联密度,并改善树脂流变特性。结果表明:改性后的炔基苯并噁嗪树脂在81. 5℃时黏度低至805 mPa·s可满足RTM工艺灌注要求,在110℃其工艺窗口高达310 min。同时,炔基苯并噁嗪树脂的起始固化温度低至130℃,固化温度为167℃,后处理温度为208℃,满足低温固化要求。通过DMA与TGA分析,RTM成型低温固化苯并噁嗪/碳纤维复合材料的Tg为411℃,在N_2环境下800℃残留率高达88. 6%,表明其复合材料具有良好的耐高温性能。SEM观察发现该树脂与纤维界面粘结强度较高,碳纤维复合材料350℃拉伸性能保留率达99%以上,弯曲、层剪性能保留率达70%以上,压缩性能保留率也达60. 9%。     

陕西太航阻火聚合物有限公司

正主要产品1 THC系列热固性耐高温耐烧蚀洁净阻燃特种酚醛树脂2 RFB增韧且可调型热固性多功能树脂3 D系列低黏度多功能热固性特种树脂,用于复合材料的RTM成型工艺,灌封浇注等4 R.RB.RBB系列耐高温、耐烧蚀、阻燃、增韧多功能环氧固化剂5多功能溶液酚醛树脂6室温固化、中温固化三元体系耐高温、耐烧蚀、阻火、增韧技术,用于轻质、隔热、耐烧蚀领域主要性能主链分解温度550℃左右,900℃残碳率最高可达77%。线烧蚀率为负值,氧指数49,基本无烟无毒。具有强大的吸收中子射线功能,并对碳纤维等炭素材料具有优异的粘接性能。     

新型无溶剂耐高温双马树脂及其碳纤维复合材料

采用双酚A型氰酸酯改性双马树脂,研制了一种新型无溶剂耐高温双马树脂基体,研究了树脂体系的黏度特性和固化反应动力学,进行了改性树脂体系的力学性能与耐热性研究,实现了1700CF/双马树脂基复合材料的湿法缠绕成型工艺.结果表明,改性双马树脂的拉伸强度为75.6 MPa,断裂伸长率为2.4%,弯曲强度为111 MPa,玻璃化转变温度为227.9℃.该改性双马树脂体系的黏度适中、适用期长且适于湿法缠绕,T700CF/双马树脂基复合材料的纵向拉伸强度为1668 MPa,纵向弯曲强度为1590 MPa,层间剪切强度为73.3MPa.     

温度条件对碳纤维上浆剂与双马树脂反应及其复合材料界面粘结的影响

为了研究工艺温度对复合材料界面的调控作用,设计采用三阶段固化工艺(即扩散、固化和后固化),考察了不同温度制度下3种碳纤维/双马树脂(BMI)复合材料界面粘结性能的变化规律。采用原子力显微镜(AFM)和傅里叶变换红外光谱(FTIR)深入分析了上浆剂对纤维表面粗糙度和化学特性的影响,研究了上浆剂的反应活性及其与双马树脂的反应性,采用微珠脱粘方法测试了碳纤维/树脂的界面剪切强度(IFSSs)。结果表明,200℃处理2h后3种碳纤维上浆剂均发生部分反应,并且170℃,2h后上浆剂均与双马树脂发生化学反应。对比不同温度条件可以发现后固化阶段对碳纤维/双马体系的界面剪切强度影响显著,未经后固化的复合材料界面性能最低;110℃和140℃恒温扩散阶段对碳纤维/双马体系的界面剪切强度的影响不明显。同种温度条件下,CF1和CF3上浆剂与双马树脂的反应程度高于CF2,相应的CF1和CF3与双马树脂的界面剪切强度较高,表明上浆剂与双马树脂间的化学反应程度是影响其界面粘结性能的主要因素。该研究结果对我国碳纤维上浆剂的研制具有参考价值。     

高韧性异构聚酰亚胺树脂及其复合材料

采用MPMR合成技术得到了低黏度、高韧性、耐高温异构聚酰亚胺树脂,该树脂预浸液常温储存期大于两个月,亚胺化后纯树脂在320℃熔体黏度<300 Pa·S,树脂浇铸体的弯曲强度>100 MPa,弯曲模量>3.0 GPa,抗拉强度可达80 MPa,断裂伸长率可达6%,固化后T5d>500℃,其中PI-4复合材料在300℃的弯曲强度保持率达到76.5%.     

陕西太航阻火聚合物有限公司

正主要产品1 THC系列热固性耐高温耐烧蚀洁净阻燃特种酚醛树脂2 RFB增韧且可调型热固性多功能树脂3 D系列低黏度多功能热固性特种树脂,用于复合材料的RTM成型工艺,灌封浇注等4 R.RB.RBB系列耐高温、耐烧蚀、阻燃、增韧多功能环氧固化剂5多功能溶液酚醛树脂6室温固化、中温固化三元体系耐高温、耐烧蚀、阻火、增韧技术,用于轻质、隔热、耐烧蚀领域     

陕西太航阻火聚合物有限公司

正主要产品1 THC系列热固性耐高温耐烧蚀洁净阻燃特种酚醛树脂2 RFB增韧且可调型热固性多功能树脂3 D系列低黏度多功能热固性特种树脂,用于复合材料的RTM成型工艺,灌封浇注等4 R.RB.RBB系列耐高温、耐烧蚀、阻燃、增韧多功能环氧固化剂5多功能溶液酚醛树脂6室温固化、中温固化三元体系耐高温、耐烧蚀、阻火、增韧技术,用于轻质、隔热、耐烧蚀领域     

改性双马来酰亚胺树脂在RFI工艺中的应用

通过在改性双马来酰亚胺5405树脂中加入耐高温热塑性塑料聚芳醚砜(PES),获得了满足RFI工艺要求、具有良好成膜性的5405A树脂膜.该树脂膜在室温不粘手,能够任意弯曲.在熔渗温度(130℃)下,低黏度(≤500mPa·s)的保持时间长达70min.在宦温存放3个月后,不溶物含量由1.25%变化为2.02%,DSC曲线表明反应的峰始温度和峰顶温度与放置前无明显差异,130℃凝胶时间由137min变化为135min.参照5405树脂的固化工艺,制备了5405A树脂浇铸体和单向碳纤维帘子布(G0827)增强5405A复合材料,并对性能进行了评价.对比5405和5405A树脂树脂浇铸体的性能表明,5405A力学性能稍有降低,但韧性得到了明显提高.     

新型聚苯并噁嗪改性树脂的制备与性能

通过预聚反应制备了一种新型聚苯并噁嗪改性树脂.利用FTIR、GPC表征了改性树脂.利用旋转黏度计、DSC、DMA和TGA分别考察了树脂的流动性能、固化行为和改性树脂固化物的热性能.结果表明:制备的苯并噁嗪改性树脂在60～ 100℃,黏度小于500 mPa·s,恒温6h黏度不明显增大,具有良好的流动性能,适用于RTM成型工艺.改性树脂聚合温度较低,具有良好的固化工艺性.改性树脂固化物在氮气气氛下Td5在430℃以上,在900℃的残重高达73.71％,Ts为353.4℃,具有良好热性能.     

基于飞机油箱模型形状特征油量测量切片步长选择方法研究

 在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明：该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

二维翼段颤振的μ控制

 采用超声电机作为作动器来实现含控制面的翼段颤振鲁棒抑制。针对作者设计的二维翼段颤振主动抑制系统，通过理论与实验相结合的方法，建立了考虑沉浮方向阻尼和作动器模型参数不确定性的控制系统模型，设计了μ控制器，并对控制器做了降阶处理。数值仿真和风洞试验表明，μ控制器可有效地抑制颤振的发生，将颤振临界速度提高23.4%。相对于H_∞控制器，μ控制器的控制效果和鲁棒性更好。     

Abnormal Shape Mould Winding

为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。     

基于H∞性能指标的质量矩拦截弹鲁棒控制

 以所建立的质量矩拦截弹数学模型为基础，利用微分几何的反馈线性化理论，得到一个解耦线性系统，考虑到拦截弹的鲁棒性要求和3个滑块的协调控制问题，提出采用双回路的设计方法，内回路采用线性二次调节器（LQR），外回路采用考虑混合灵敏度问题的H_∞控制设计。仿真结果证明了该方法动态性能满足设计要求，同时对系统参数的不确定性具有较强的鲁棒性。     

航天器返回地球的气动特性综述

航天器返回地球的飞行过程中,气动特性是实现将宇宙飞行速度减到落地前速度、保证再入飞行得到有效控制以及再入防热安全可靠的关键因素。针对简单旋成体气动外形、半弹道式再入控制、烧蚀防热类返回航天器,综述了返回地球过程中变化的空气流域特性、航天器周围的气体绕流环境、空气与航天器作用产生的动力学与热效应等。系统地给出了该类航天器的再入气动特性参数与飞行性能的共性规律,包括:气动阻力与再入减速、气动升力与再入轨迹控制、配平攻角与飞行稳定性、气动加热与防热,以及再入过程中不同气动特性航天器、气象条件变化等对再入飞行性能的影响规律。为航天器开展返回飞行过程的跨流域气动性能工程研制提供设计参考。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.