供电系统的干扰模式及抑制措施

供电系统的电磁干扰主要由发电机噪声、整流谐波、开关频率和它的谐波,以及在开关转换中高速电流和电压的瞬变所引起,这些干扰可通过传导和辐射的方式直接影响交流电网和用电设备。所以,本文所要讨论的主要问题就是电磁干扰的解决方法。     

Synthetic Aperture Radar

The general theory of side-looking synthetic aperture radar systems is developed. A simple circuit-theory model is developed; the geometry of the system determines the nature of the prefilter and the receiver (or processor) is the postfilter. The complex distributed reflectivity density appears as the input, and receiver noise is first considered as the interference which limits performance. Analysis and optimization are carried out for three performance criteria (resolution, signal-to-noise ratio, and least squares estimation of the target field). The optimum synthetic aperture length is derived in terms of the noise level and average transmitted power. Range-Doppler ambiguity limitations and optical processing are discussed briefly. The synthetic aperture concept for rotating target fields is described. It is observed that, for a physical aperture, a side-looking radar, and a rotating target field, the azimuth resolution is ?/? where ? is the change in aspect angle over which the target field is viewed, The effects of phase errors on azimuth resolution are derived in terms of the power density spectrum of the derivative of the phase errors and the performance in the absence of phase errors.     

Noise factor and antenna gains in the signal/noise equation for over-the-horizon radar

A recommended form of the signal-to-noise equation that includes both internal and external system noise and signal/noise processing losses is discussed. The recommended form conforms to the internationally accepted definition of system operating noise factor but is extended to include signal/noise processing. The predetection signal-to-noise ratio (SNR) of a radar or communication system is proportional to the power gain of the transmit antenna and the directive gain of the receive antenna, and is inversely proportional to the operating noise factor of the receiving system. The operating noise factor is approximately equal to the product of the external noise factor and the signal/noise processing factor when the system is external noise limited, as is usually the case for over-the-horizon (OTH) radar.<>     

提高TDICCD相机成像质量的研究

根据TDICCD器件的特点，分析了光学系统，像元尺寸对图像分辨力的影响，研究了器件噪声，速高比和曝光控制对图像质量的影响，采用相关双采样技术，速高比自动引入和自动曝光技术，提高了TDICCD相机的成像质量。     

Some Matched Filter Configurations for Infrared Systems

An analysis of the output of three alternative matched filter configurations in an infrared scanning system model is presented. The sensor is corrupted by thermal noise, generation-recombination noise, photon noise, and modulation noise, the latter providing an extreme discoloration in the signal passband. Expressions for the signal voltage density spectrum, signal pulse shape, noise power spectrum, and average noise power at the matched filter output are derived where the integral evaluations attendant to these derivations do not appear elsewhere in the literature. The paper also provides graphical displays of the signal-to-noise power ratio at the filter output versus various system parameters, noise power spectrum out of the matched filter versus ?, and the signal pulse shape out of the filter versus time. Also included are discussions of practically realizable approximations to the matched filters and curve fitting techniques for the signal pulse shape function.     

大气湍流对APD直接检测接收机抗噪声性能影响

针对以往分析湍流信道对系统抗噪声性能影响的不足,给出了一种基于APD直接检测接收机的湍流噪声的处理方法.在APD直接检测接收机模型的基础上,推导了其信噪比和曼彻斯特编码系统的差错概率,并详细分析了湍流对接收机的抗噪声性能影响.结果表明,增大接收天线孔径可以减弱湍流的影响,但在天线孔径较小时,增加发射功率并不能有效地提高...     

High gain airborne antenna for satellite communications

The performance of an airborne phased-array antenna, which was developed and evaluated onboard a commercial aircraft using the Engineering Test Satellite V (ETS-V), is reported. The system requirements and the antenna configuration that satisfies them are described. The radiation pattern, gain and axial ratio, noise temperature and ratio of gain to noise temperature, and environmental characteristics are presented. The results obtained by the flight experiments demonstrate that the performance of the antenna is the same as that on the ground, so that the antenna is suitable for installation in an aircraft for satellite communications     

叠加法测量光纤功率计非线性

介绍了全光纤化光纤功率计非线性的宽动态范围测量系统,利用该系统可以测量光纤功率计相邻量程的不连续性.文中给出了具体测量数据,并对测量结果进行了不确定度分析.     

Bandwidth maximization for satellite laser communication

Free space optical communication between satellites networked together can make possible high speed communication between different places on Earth. The basic free space optical communication network includes at least two satellites. In order to communicate between them, the transmitter satellite must track the beacon of the receiver satellite and point the information optical beam in its direction. The pointing systems for laser satellite communication suffer during tracking from vibration due to electronic noise, background radiation from interstellar objects such as Sun, Moon, Earth, and Stars in the tracking field of view, and mechanical impact from satellite internal and external sources. Due to vibrations the receiver receives less power. This effect limits the system bandwidth for given bit error rate (BER). In this research we derive an algorithm to maximize the communication system bandwidth using the transmitter telescope gain as a free variable based on the vibration statistics model and the system parameters. Our model makes it possible to adapt the bandwidth and transmitter gain to change of vibration amplitude. We also present an example of a practical satellite network which includes a direct detection receiver with an optical amplifier. A bandwidth improvement of three orders of magnitude is achieved in this example for certain conditions, as compared with an unoptimized system     

FSO链路中基于平均信噪比的自适应功率传输技术

文章提出了 1种基于平均信噪比(Signal-to-Noise Ratio,SNR)的自适应功率传输技术,旨在补偿大气湍流引起的闪烁效应,以提升自由空间光(Free-Space Optical,FSO)通信系统的性能。在无需大气湍流状态信息估计的情况下,根据接收信号的平均 SNR来调整发射信号的发射功率,实现基于自适应功率传输技术的大气湍流效应补偿。建立了不同湍流强度下具有不同噪声水平的信道模型,并将所提出的技术与固定阈值判决(Fixed Threshold Deci-sion,FTD)和自适应阈值判决(Adaptive Threshold Decision,ATD)技术进行了比较分析。仿真结果表明,在不同的湍流强度下,该技术的误码率(Bit Error Rate,BER)性能相较于 FTD有了显著的提高,并且接近于 ATD。因此,该技术可以有效提高 FSO链路的通信能力。     

Postfiltering in Digital Beamformers

Assuming a sinusoidal signal superimposed on a narrow-band Gaussian noise as the input to a receiving array, the output power and signal-to-noise ratio of a digital beamformer with postfiltering were formulated so that subsequent calculations could be made without an analysis in the frequency domain. The formulation utilized the quantizer functions previously given by the author and certain spectral power distribution factors originally attributed to Davenport but more rigorously derived and discussed in the present work. A numerical study based on this formulation for a DIMUS array in a correlated noise field reveals that except for certain rare circumstances, postfiltering generally improves the output SNR or array gain. It is demonstrated that the amount of postfiltering gain not only varies with array input SNR but also depends strongly upon the spacing-to-wavelength ratio, and its meaningful interpretation can only be made in conjunction with both the clipping and noise correlation losses. In particular, balancing postfiltering gain against the two losses suggests that receiving arrays with element spacings smaller than one-half of the operating wavelength may be used to the advantage of system design under certain conditions.     

测量系统特性对压敏涂料校准影响的实验研究

针对压敏涂料(PSP)的特性,基于自行建立的光学压力测量系统,研究了CCD相机光圈与激发光源强度对校准结果的影响。对压力为27.4～147.4kPa,相机光圈F值为2.8～11.0,激发光源在200W、400W两种强度条件下分别开展了国产压敏涂料的校准实验,每一采样点采集20次。通过对所采集荧光图像进行平均、比运算等一系列图像处理后,可得到不同条件下的压力校准曲线,分析了相机光圈与激发光源强度对压敏涂料压敏特性的影响。实验研究结果表明:经过比运算可以消除系统和光照不均匀对压敏涂料发光的影响;激发光需具有一定强度,激发光的强度要足以使涂料中的光敏分子产生能级的跃迁;相机的光圈值越大,所采集到的图像信噪比越大,获得的压敏涂料校准曲线斜率越大。     

电子加速器在大型工业CT中的应用研究

以大型工业CT 检测系统中的电子加速器 X 射线源为研究对象,分析了驻波电子加速器在大型工业 CT 应用中遇到的能量选择、张角的大小、能量空间分布问题;并从理论上分析研究了高能 X 射线在探测器之间的相互窜扰的影响,给出了高能 X 射线窜扰的校正方法。     

Pulse-Position Modulation Based on Energy Detection

A pulse-position modulation (PPM) system based on energy detection is described. The system is shown to be applicable to a communication system in which the arrival times of signals are unknown. The decision statistics are chisquare distributed (either central or noncentral), and recursive methods of computing probabilities of error are derived. A simple digital processor for implementing the system is also described.     

Detection of Known Signals in Nonstationary Noise

The basic design of a nonlinear, time-invariant filter is postulated for detecting signal pulses of known shape imbedded in nonstationary noise. The noise is a sample function of a Gaussian random process whose statistics are approximately constant during the length of a signal pulse. The parameters of the filter are optimized to maximize the output signal-to-noise ratio (SNR). The resulting nonlinear filter has the interesting property of approximating the performance of an adaptive filter in that it weights each frequency band of each input pulse by a factor that depends on the instantaneous noise power spectrum present at that time. The SNR at the output of the nonlinear filter is compared to that at the output of a matched filter. The relative performance of the nonlinear system is good when the signal pulses have large time-bandwidth products and the instantaneous noise power spectrum is colored in the signal pass band.     

Efficient prediction of ground noise from helicopters and parametric studies based on acoustic mapping

Based on the acoustic mapping, a prediction model for the ground noise radiated from an in-flight helicopter is established. For the enhancement of calculation efficiency, a high-efficiency second-level acoustic radiation model capable of taking the influence of atmosphere absorption on noise into account is first developed by the combination of the point-source idea and the rotor noise radiation characteristics. The comparison between the present model and the direct computation method of noise is done and the high efficiency of the model is validated. Rotor free-wake analysis method and Ffowcs Williams-Hawkings (FW-H) equation are applied to the aerodynamics and noise prediction in the present model. Secondly, a database of noise spheres with the characteristic parameters of advance ratio and tip-path-plane angle is established by the helicopter trim model together with a parametric modeling approach. Furthermore, based on acoustic mapping, a method of rapid simulation for the ground noise radiated from an in-flight helicopter is developed. The noise footprint for AH-1 rotor is then calculated and the influence of some parameters including advance ratio and flight path angle on ground noise is deeply analyzed using the developed model. The results suggest that with the increase of advance ratio and flight path angle, the peak noise levels on the ground first increase and then decrease, in the meantime, the maximum Sound Exposure Level (SEL) noise on the ground shifts toward the advancing side of rotor. Besides, through the analysis of the effects of longitudinal forces on miss-distance and rotor Blade-Vortex Interaction (BVI) noise in descent flight, some meaningful results for reducing the BVI noise on the ground are obtained.     

Numerical study on similarity of plume infrared radiation between reduced-scale solid rocket motors

This study seeks to determine the similarities in plume radiation between reduced and full-scale solid rocket models in ground test conditions through investigation of flow and radiation for a series of scale ratios ranging from 0.1 to 1. The radiative transfer equation(RTE) considering gas and particle radiation in a non-uniform plume has been adopted and solved by the finite volume method(FVM) to compute the three dimensional, spectral and directional radiation of a plume in the infrared waveband 2–6 μm. Conditions at wavelengths 2.7 μm and 4.3 μm are discussed in detail, and ratios of plume radiation for reduced-scale through full-scale models are examined. This work shows that, with increasing scale ratio of a computed rocket motor, area of the hightemperature core increases as a 2 power function of the scale ratio, and the radiation intensity of the plume increases with 2–2.5 power of the scale ratio. The infrared radiation of plume gases shows a strong spectral dependency, while that of Al_2O_3 particles shows spectral continuity of gray media.Spectral radiation intensity of a computed solid rocket plume's high temperature core increases significantly in peak radiation spectra of plume gases CO and CO_2. Al_2O_3 particles are the major radiation component in a rocket plume. There is good similarity between contours of plume spectral radiance from different scale models of computed rockets, and there are two peak spectra of radiation intensity at wavebands 2.7–3.0 μm and 4.2–4.6 μm. Directed radiation intensity of the entire plume volume will rise with increasing elevation angle.     

Analysis of a Long-Distance System Measuring the Concentration of Atmospheric Gaseous Pollutants

A detailed inaccuracy and sensitivity analysis of a long-distance air pollution detection system, using a laser measuring the resonance absorption of polluting molecules, is introduced. The noise and the dynamic range of the radiation detectors used, the atmospheric inhomogeneities, and the atmospheric propagation losses of the electromagnetic radiation are considered. In addition, the best measuring path length as a function of a molecule density and atmospheric transparency and irregularity is discussed.     

高频噪声场中薄壁结构响应的预估

本文用统计能量分析(StatisticalEnergyAnalysis简称SEA)法研究了在高频宽带随机噪声场中板及加筋板(航空航天器用蒙皮)的加速度响应。发现,在高频段同样外场激励情况下,加筋板的响应大于光板的。本文解释了这一用质量定理无法解释的现象,并用叠加法确定了复杂结构加筋板的模态密度、辐射阻抗和输入功率。     

Error Performance of Two-Channel Phase-Measurement Systems

The problem of measuring a constant phase difference between two sinusoids which have been corrupted by two additive noise processes is investigated. For the case in which both noise processes are Gaussian and the signal-to-noise ratio is high, the variance of the time-averaged phase-difference estimate is found as a single integral over the noise power spectral densities and cross spectral density. Arbitrary cross correlation is allowed between the two noise processes. Two cases of practical interest are considered: 1) the noise processes have identical, rectangular power spectral densities and are statistically independent; 2) an idealized radio direction finding situation in which two spatially separated sensors are immersed in an isotropic, planar noise field. For the statistically independent case, a universal curve is presented which permits determination of phase-estimate standard deviation for arbitrary signal-to-noise ratio and for a wide range of bandwidths and integration times.