Selection of the Mars Science Laboratory Landing Site

The selection of Gale crater as the Mars Science Laboratory landing site took over five years, involved broad participation of the science community via five open workshops, and narrowed an initial >50 sites (25 by 20?km) to four finalists (Eberswalde, Gale, Holden and Mawrth) based on science and safety. Engineering constraints important to the selection included: (1)?latitude (±30°) for thermal management of the rover and instruments, (2)?elevation (<?1?km) for sufficient atmosphere to slow the spacecraft, (3)?relief of <100–130?m at baselines of 1–1000?m for control authority and sufficient fuel during powered descent, (4)?slopes of <30° at baselines of 2–5?m for rover stability at touchdown, (5)?moderate rock abundance to avoid impacting the belly pan during touchdown, and (6)?a?radar-reflective, load-bearing, and trafficable surface that is safe for landing and roving and not dominated by fine-grained dust. Science criteria important for the selection include the ability to assess past habitable environments, which include diversity, context, and biosignature (including organics) preservation. Sites were evaluated in detail using targeted data from instruments on all active orbiters, and especially Mars Reconnaissance Orbiter. All of the final four sites have layered sedimentary rocks with spectral evidence for phyllosilicates that clearly address the science objectives of the mission. Sophisticated entry, descent and landing simulations that include detailed information on all of the engineering constraints indicate all of the final four sites are safe for landing. Evaluation of the traversabilty of the landing sites and target “go to” areas outside of the ellipse using slope and material properties information indicates that all are trafficable and “go to” sites can be accessed within the lifetime of the mission. In the final selection, Gale crater was favored over Eberswalde based on its greater diversity and potential habitability.     

Thermal Properties of Icy Surfaces in the Outer Solar System

The thermal properties of airless icy surfaces are providing a wealth of information on their regolith structure after eons of space weathering. Numerous observations of the thermal cycles of Jupiter and Saturn icy satellites or Centaurs and TNOs have been acquired in the latest decades thanks to the Galileo and Cassini missions and to the Spitzer and Herschel telescopes. These observations and the latest developments on thermophysical modeling which have been achieved to link the thermal inertia to the regolith structure are reviewed here. Measured thermal inertias of these surfaces covered with water ice are very low, roughly between about 1 and 100 J/m²/K/s^1/2. Often interpreted as due to unconsolidated or highly porous regoliths, these low values may result from a composition of amorphous ice or from the roughness of grains defacing contacts in a regolith of normal compaction. Taken together, thermal inertias appear to increase with probed depth and to decrease with heliocentric distance. This latter effect can be easily reproduced if heat transfer is dominated by radiation in pores, despite low temperatures, because the conduction through grains is limited, either due to the presence of amorphous ice or because of the roughness of grains.     

How Well Do Experimental Results on Large Samples of Gas-Laden Amorphous Ice Duplicate Deep Impact’s Findings?

The findings of Deep Impact on the structure and composition of Tempel-1 are compared with our experimental results on large (20 cm diameter and up to 10 cm high) samples of gas-laden amorphous ice which does not contain dust. The mechanical ～tensile strength inferred for Tempel-1: up to 12 kPa is close to our experimental findings of 2–4 kPa. This means that Tempel-1 is as fluffy as our very fluffy, talcum like, ice sample. The thermal inertia: 30<I<100 W?K^?1?m^?2?s^1/2 is close to our value of 80. The density of 350±250 kg?m^?3, is close to our value of 250–300 kg?m^?3, taking into account an ice/silicate ratio of 1 in the comet, while we study pure ice. Surface morphological features, such as non-circular depressions and chaotic terrain, were observed in our experiments. The only small increase in the gas/water vapor ratio pre- and post-impact, suggest that in the area excavated by the impactor, the 135 K front did not penetrate deeper than a few meters. Altogether, the agreement between the findings of Deep Impact and our experimental results point to a loose agglomerate of ice grains (with a silicate-organic core), which was formed by a very gentle aggregation of the ice grains, without compaction.     

Characterization and Calibration of the CheMin Mineralogical Instrument on Mars Science Laboratory

A principal goal of the Mars Science Laboratory (MSL) rover Curiosity is to identify and characterize past habitable environments on Mars. Determination of the mineralogical and chemical composition of Martian rocks and soils constrains their formation and alteration pathways, providing information on climate and habitability through time. The CheMin X-ray diffraction (XRD) and X-ray fluorescence (XRF) instrument on MSL will return accurate mineralogical identifications and quantitative phase abundances for scooped soil samples and drilled rock powders collected at Gale Crater during Curiosity’s 1-Mars-year nominal mission. The instrument has a Co X-ray source and a cooled charge-coupled device (CCD) detector arranged in transmission geometry with the sample. CheMin’s angular range of 5^° to 50^° 2θ with <0.35^° 2θ resolution is sufficient to identify and quantify virtually all minerals. CheMin’s XRF requirement was descoped for technical and budgetary reasons. However, X-ray energy discrimination is still required to separate Co?Kα from Co?Kβ and Fe?Kα photons. The X-ray energy-dispersive histograms (EDH) returned along with XRD for instrument evaluation should be useful in identifying elements Z>13 that are contained in the sample. The CheMin XRD is equipped with internal chemical and mineralogical standards and 27 reusable sample cells with either Mylar^? or Kapton^? windows to accommodate acidic-to-basic environmental conditions. The CheMin flight model (FM) instrument will be calibrated utilizing analyses of common samples against a demonstration-model (DM) instrument and CheMin-like laboratory instruments. The samples include phyllosilicate and sulfate minerals that are expected at Gale crater on the basis of remote sensing observations.     

High-temperature oxidation behavior and analysis of impedance spectroscopy of 7YSZ thermal barrier coating prepared by plasma spray-physical vapor deposition

Quasi-columnar structure 7YSZ(yttria stabilized zirconia) thermal barrier coatings(TBCs) are prepared by plasma spray-physical vapor deposition(PS-PVD) onto pretreated and un-pretreated bond coating, respectively. An isothermal oxidation experiment of 7YSZ TBCs is carried out in the atmosphere of 950 °C in order to simulate the high-temperature oxidation process of engine blades. The isothermal oxidation process of 7YSZ thermal barrier coatings is investigated systematically by impedance spectroscopy. The electrochemical physical model and equivalent circuit of columnar 7YSZ coatings are established. Results show that the isothermal oxidation kinetic curve of columnar 7YSZ thermal barrier coatings appears to follow the parabolic law. A pretreatment of bond coating can reduce the growth rate of the thermally grown oxide(TGO) layer, restraining the initiation and propagation of microcracks between YSZ and TGO layers. The oxidation rate constants of 7YSZ coatings with pretreated and un-pretreated bond coating are 0.101×10~(-12) cm~2·s~(-1) and 0.115 × 10~(-13) cm~2 ·s~(-1), respectively. Impedance analysis shows that the content of oxygen vacancies decreases and the density increases after the TGO layer is oxidized for 150 h. In addition, shrinkage microcracks formed by sintering during the oxidation process is the main reason for an increase of the capacitance and a decrease of the resistance in the grain boundary of YSZ.     

Mars Science Laboratory Mission and Science Investigation

Scheduled to land in August of 2012, the Mars Science Laboratory (MSL) Mission was initiated to explore the habitability of Mars. This includes both modern environments as well as ancient environments recorded by the stratigraphic rock record preserved at the Gale crater landing site. The Curiosity rover has a designed lifetime of at least one Mars year (～23?months), and drive capability of at least 20?km. Curiosity’s science payload was specifically assembled to assess habitability and includes a gas chromatograph-mass spectrometer and gas analyzer that will search for organic carbon in rocks, regolith fines, and the atmosphere (SAM instrument); an x-ray diffractometer that will determine mineralogical diversity (CheMin instrument); focusable cameras that can image landscapes and rock/regolith textures in natural color (MAHLI, MARDI, and Mastcam instruments); an alpha-particle x-ray spectrometer for in situ determination of rock and soil chemistry (APXS instrument); a?laser-induced breakdown spectrometer to remotely sense the chemical composition of rocks and minerals (ChemCam instrument); an active neutron spectrometer designed to search for water in rocks/regolith (DAN instrument); a weather station to measure modern-day environmental variables (REMS instrument); and a sensor designed for continuous monitoring of background solar and cosmic radiation (RAD instrument). The various payload elements will work together to detect and study potential sampling targets with remote and in situ measurements; to acquire samples of rock, soil, and atmosphere and analyze them in onboard analytical instruments; and to observe the environment around the rover. The 155-km diameter Gale crater was chosen as Curiosity’s field site based on several attributes: an interior mountain of ancient flat-lying strata extending almost 5?km above the elevation of the landing site; the lower few hundred meters of the mountain show a progression with relative age from clay-bearing to sulfate-bearing strata, separated by an unconformity from overlying likely anhydrous strata; the landing ellipse is characterized by a mixture of alluvial fan and high thermal inertia/high albedo stratified deposits; and a number of stratigraphically/geomorphically distinct fluvial features. Samples of the crater wall and rim rock, and more recent to currently active surface materials also may be studied. Gale has a well-defined regional context and strong evidence for a progression through multiple potentially habitable environments. These environments are represented by a stratigraphic record of extraordinary extent, and insure preservation of a rich record of the environmental history of early Mars. The interior mountain of Gale Crater has been informally designated at Mount Sharp, in honor of the pioneering planetary scientist Robert Sharp. The major subsystems of the MSL Project consist of a single rover (with science payload), a Multi-Mission Radioisotope Thermoelectric Generator, an Earth-Mars cruise stage, an entry, descent, and landing system, a launch vehicle, and the mission operations and ground data systems. The primary communication path for downlink is relay through the Mars Reconnaissance Orbiter. The primary path for uplink to the rover is Direct-from-Earth. The secondary paths for downlink are Direct-to-Earth and relay through the Mars Odyssey orbiter. Curiosity is a scaled version of the 6-wheel drive, 4-wheel steering, rocker bogie system from the Mars Exploration Rovers (MER) Spirit and Opportunity and the Mars Pathfinder Sojourner. Like Spirit and Opportunity, Curiosity offers three primary modes of navigation: blind-drive, visual odometry, and visual odometry with hazard avoidance. Creation of terrain maps based on HiRISE (High Resolution Imaging Science Experiment) and other remote sensing data were used to conduct simulated driving with Curiosity in these various modes, and allowed selection of the Gale crater landing site which requires climbing the base of a mountain to achieve its primary science goals. The Sample Acquisition, Processing, and Handling (SA/SPaH) subsystem is responsible for the acquisition of rock and soil samples from the Martian surface and the processing of these samples into fine particles that are then distributed to the analytical science instruments. The SA/SPaH subsystem is also responsible for the placement of the two contact instruments (APXS, MAHLI) on rock and soil targets. SA/SPaH consists of a robotic arm and turret-mounted devices on the end of the arm, which include a drill, brush, soil scoop, sample processing device, and the mechanical and electrical interfaces to the two contact science instruments. SA/SPaH also includes drill bit boxes, the organic check material, and an observation tray, which are all mounted on the front of the rover, and inlet cover mechanisms that are placed over the SAM and CheMin solid sample inlet tubes on the rover top deck.     

An Overview of Earth’s Global Electric Circuit and Atmospheric Conductivity

The Earth’s global atmospheric electric circuit depends on the upper and lower atmospheric boundaries formed by the ionosphere and the planetary surface. Thunderstorms and electrified rain clouds drive a DC current (～1 kA) around the circuit, with the current carried by molecular cluster ions; lightning phenomena drive the AC global circuit. The Earth’s near-surface conductivity ranges from 10^?7 S?m^?1 (for poorly conducting rocks) to 10^?2 S?m^?1 (for clay or wet limestone), with a mean value of 3.2 S?m^?1 for the ocean. Air conductivity inside a thundercloud, and in fair weather regions, depends on location (especially geomagnetic latitude), aerosol pollution and height, and varies from ～10^?14 S?m^?1 just above the surface to 10^?7 S?m^?1 in the ionosphere at ～80 km altitude. Ionospheric conductivity is a tensor quantity due to the geomagnetic field, and is determined by parameters such as electron density and electron–neutral particle collision frequency. In the current source regions, point discharge (coronal) currents play an important role below electrified clouds; the solar wind-magnetosphere dynamo and the unipolar dynamo due to the terrestrial rotating dipole moment also apply atmospheric potential differences. Detailed measurements made near the Earth’s surface show that Ohm’s law relates the vertical electric field and current density to air conductivity. Stratospheric balloon measurements launched from Antarctica confirm that the downward current density is ～1 pA m^?2 under fair weather conditions. Fortuitously, a Solar Energetic Particle (SEP) event arrived at Earth during one such balloon flight, changing the observed atmospheric conductivity and electric fields markedly. Recent modelling considers lightning discharge effects on the ionosphere’s electric potential (～+250 kV with respect to the Earth’s surface) and hence on the fair weather potential gradient (typically ～130 V?m^?1 close to the Earth’s surface. We conclude that cloud-to-ground (CG) lightning discharges make only a small contribution to the ionospheric potential, and that sprites (namely, upward lightning above energetic thunderstorms) only affect the global circuit in a miniscule way. We also investigate the effects of mesoscale convective systems on the global circuit.     

等离子喷涂LaTi2Al9O19热障涂层的微观组织结构及热物理性能

 第一代热障涂层(TBCs)由氧化钇部分稳定的氧化锆(YSZ)陶瓷隔热层和金属粘结层组成,该涂层长期使用温度低于1 200℃。随着先进航空发动机向着高推重比发展,迫切要求发展新一代超高温、高隔热热障涂层材料。LaTi₂Al₉O₁₉(LTA)在1 500℃长期保持相稳定,是一种非常有前景的超高温热障涂层候选材料。本文采用大气等离子喷涂(APS)制备了LTA涂层,研究了喷涂工艺对涂层微观组织结构和热物理性能的影响。结果表明沉积态涂层中含少量的非晶态,在860℃和1 130℃出现晶化峰。等离子喷涂过程中La₂O₃挥发量较多,导致沉积态涂层中La元素与原始粉末相比含量偏低,而其他组分的化学成分随喷涂功率变化不大。LTA涂层的热扩散系数在1 400℃下为0.3~0.4 mm²·s^-1,热导率为1.1~1.6 W·m^-1·K^-1。1 050℃经过20小时热处理后,得到晶化的涂层在晶化温度范围内的热扩散系数和热导率值均增大。随着喷涂功率减小,涂层孔隙率增加,热导率减小。     

Large-scale Bright Fronts in the Solar Corona: A?Review of?��EIT waves��

??EIT waves?? are large-scale coronal bright fronts (CBFs) that were first observed in 195 Å images obtained using the Extreme-ultraviolet Imaging Telescope (EIT) onboard the Solar and Heliospheric Observatory (SOHO). Commonly called ??EIT waves??, CBFs typically appear as diffuse fronts that propagate pseudo-radially across the solar disk at velocities of 100?C700 km?s^?1 with front widths of 50?C100 Mm. As their speed is greater than the quiet coronal sound speed (c _s ??200 km?s^?1) and comparable to the local Alfvén speed (v _A ??1000 km?s^?1), they were initially interpreted as fast-mode magnetoacoustic waves ( $v_{f}=(c_{s}^{2} + v_{A}^{2})^{1/2}$ ). Their propagation is now known to be modified by regions where the magnetosonic sound speed varies, such as active regions and coronal holes, but there is also evidence for stationary CBFs at coronal hole boundaries. The latter has led to the suggestion that they may be a manifestation of a processes such as Joule heating or magnetic reconnection, rather than a wave-related phenomena. While the general morphological and kinematic properties of CBFs and their association with coronal mass ejections have now been well described, there are many questions regarding their excitation and propagation. In particular, the theoretical interpretation of these enigmatic events as magnetohydrodynamic waves or due to changes in magnetic topology remains the topic of much debate.     

The New Horizons Radio Science Experiment (REX)

The New Horizons (NH) Radio Science Experiment, REX, is designed to determine the atmospheric state at the surface of Pluto and in the lowest few scale heights. Expected absolute accuracies in n, p, and T at the surface are 4?10¹⁹ m^?3, 0.1 Pa, and 3 K, respectively, obtained by radio occultation of a 4.2 cm-λ signal transmitted from Earth at 10–30 kW and received at the NH spacecraft. The threshold for ionospheric observations is roughly 2?10⁹ e^??m^?3. Radio occultation experiments are planned for both Pluto and Charon, but the level of accuracy for the neutral gas is expected to be useful at Pluto only. REX will also measure the nightside 4.2 cm-λ thermal emission from Pluto and Charon during the time NH is occulted. At Pluto, the thermal scan provides about five half-beams across the disk; at Charon, only disk integrated values can be obtained. A combination of two-way tracking and occultation signals will determine the Pluto system mass to about 0.01 percent, and improve the Pluto–Charon mass ratio. REX flight equipment augments the NH radio transceiver used for spacecraft communications and tracking. Implementation of REX required realization of a new CIC-SCIC signal processing algorithm; the REX hardware implementation requires 1.6 W, and has mass of 160 g in 520 cm³. Commissioning tests conducted after NH launch demonstrate that the REX system is operating as expected.     

R141b在圆形微通道内的沸腾换热实验研究

为提高换热强度、解决设备内部高热流密度散热问题,采用实验方法研究R141b在不同直径(D=0.5mm和1.0mm)水平圆形微通道内的沸腾换热特性,分析了热流密度(q=2.0kW/m~2～47.6kW/m~2)、质量干度(x=0～0.6)、质量流速(G=111.11kg/(m~2·s)～333.33kg/(m~2·s))的变化对平均传热系数h的影响,探究不同情况下影响沸腾换热的主导因素。实验研究表明:平均传热系数h随热流密度q的增加而减小,在不同范围内减小速率有明显差异;热流密度q=2kW/m~2～5kW/m~2时质量流速G对平均传热系数h影响较明显,热流密度较高时质量流速G对换热影响很小;在质量流速G=111.11kg/(m~2·s)～333.33kg/(m~2·s),质量干度x0.3时,平均传热系数h随质量干度x增加而明显下降,在设计微通道换热器时应尽量使R141b处于初始沸腾阶段以获得更好换热效果,并采取一定措施预防干度过高引起的换热恶化。     

Properties of Ground Level Enhancement Events and the Associated Solar Eruptions During Solar Cycle 23

Solar cycle 23 witnessed the most complete set of observations of coronal mass ejections (CMEs) associated with the Ground Level Enhancement (GLE) events. We present an overview of the observed properties of the GLEs and those of the two associated phenomena, viz., flares and CMEs, both being potential sources of particle acceleration. Although we do not find a striking correlation between the GLE intensity and the parameters of flares and CMEs, the solar eruptions are very intense involving X-class flares and extreme CME speeds (average ～2000?km/s). An M7.1 flare and a 1200?km/s CME are the weakest events in the list of 16 GLE events. Most (80?%) of the CMEs are full halos with the three non-halos having widths in the range 167 to 212?degrees. The active regions in which the GLE events originate are generally large: 1290?msh (median 1010?msh) compared to 934?msh (median: 790?msh) for SEP-producing active regions. For accurate estimation of the CME height at the time of metric type?II onset and GLE particle release, we estimated the initial acceleration of the CMEs using flare and CME observations. The initial acceleration of GLE-associated CMEs is much larger (by a factor of 2) than that of ordinary CMEs (2.3?km/s² vs. 1?km/s²). We confirmed the initial acceleration for two events for which CME measurements are available in the inner corona. The GLE particle release is delayed with respect to the onset of all electromagnetic signatures of the eruptions: type?II bursts, low frequency type?III bursts, soft X-ray flares and CMEs. The presence of metric type?II radio bursts some 17?min (median: 16?min; range: 3 to 48?min) before the GLE onset indicates shock formation well before the particle release. The release of GLE particles occurs when the CMEs reach an average height of ～3.09?R _s (median: 3.18?R _s ; range: 1.71 to 4.01?R _s ) for well-connected events (source longitude in the range W20–W90). For poorly connected events, the average CME height at GLE particle release is ～66?% larger (mean: 5.18?R _s ; median: 4.61?R _s ; range: 2.75–8.49?R _s ). The longitudinal dependence is consistent with shock accelerations because the shocks from poorly connected events need to expand more to cross the field lines connecting to an Earth observer. On the other hand, the CME height at metric type?II burst onset has no longitudinal dependence because electromagnetic signals do not require magnetic connectivity to the observer. For several events, the GLE particle release is very close to the time of first appearance of the CME in the coronagraphic field of view, so we independently confirmed the CME height at particle release. The CME height at metric type?II burst onset is in the narrow range 1.29 to 1.8?R _s , with mean and median values of 1.53 and 1.47?R _s . The CME heights at metric type?II burst onset and GLE particle release correspond to the minimum and maximum in the Alfvén speed profile. The increase in CME speed between these two heights suggests an increase in Alfvénic Mach number from?2 to?3. The CME heights at GLE particle release are in good agreement with those obtained from the velocity dispersion analysis (Reames in Astrophys. J. 693:812, 2009a; Astrophys. J. 706:844, 2009b) including the source longitude dependence. We also discuss the implications of the delay of GLE particle release with respect to complex type?III bursts by ～18?min (median: 16?in; range: 2 to 44?min) for the flare acceleration mechanism. A?similar analysis is also performed on the delay of particle release relative to the hard X-ray emission.     

Thermophysics of the planet Mercury

Recent observations of the thermal emission of Mercury at microwave and infrared frequencies now permit a determination of the thermal and electrical properties of the subsurface of the planet. Radar and optical measurements show that the rotation period is 58.65 days, 2/3 of the orbital period. Several negative spectrographic searches verify that the effects of an atmosphere need not be taken into account in computing surface and subsurface temperatures. The observed thermal emission from the planet can then be interpreted from models similar to those developed for study of the Moon but adapted to the peculiar diurnal insolation of Mercury. The observations of Epstein et al. (1970) at 3.3 mm and of Klein (1970a) at 3.75 cm, when interpreted together with recent laboratory measurements of thermal properties of terrestrial and lunar rock powders, indicate that the ratio of electrical to thermal skin depth is 0.9 ± 0.3 times the wavelength in centimeters. Further results of this analysis of the subsurface are: Density = 1.5 ± 0.4 g cm^-3; Electric loss tangent = 0.009 ± 0.004; Inverse thermal inertia = (15 ± 6) × 10^–6 erg^-1 cm² s^1/2 K; Equatorial midnight temperature = 100 ± 15K.The microwave data generally conform to the predictions of the thermophysical models of Mercury developed by Morrison and Sagan (1967), including a suggestion that variations having mean periods of 50 days and 35 days are present in addition to the classical phase effect with period about 116 days. The time-averaged microwave temperature of the planet appears to increase 25 % from millimeter to decimeter wavelengths; this increase suggests that radiation plays an important role in the transport of heat in the subsurface. All of the conclusions of this review indicate that the thermophysical behavior of Mercury closely approximates that expected for the Moon, were it placed in the orbit of Mercury.     

The Pioneer Anomaly in the Light of New Data

The radio-metric tracking data received from the Pioneer 10 and 11 spacecraft from the distances between 20–70 astronomical units from the Sun has consistently indicated the presence of a small, anomalous, blue-shifted Doppler frequency drift that limited the accuracy of the orbit reconstruction for these vehicles. This drift was interpreted as a sunward acceleration of a _P =(8.74±1.33)×10^?10 m/s² for each particular spacecraft. This signal has become known as the Pioneer anomaly; the nature of this anomaly is still being investigated. Recently new Pioneer 10 and 11 radio-metric Doppler and flight telemetry data became available. The newly available Doppler data set is much larger when compared to the data used in previous investigations and is the primary source for new investigation of the anomaly. In addition, the flight telemetry files, original project documentation, and newly developed software tools are now used to reconstruct the engineering history of spacecraft. With the help of this information, a thermal model of the Pioneers was developed to study possible contribution of thermal recoil force acting on the spacecraft. The goal of the ongoing efforts is to evaluate the effect of on-board systems on the spacecrafts’ trajectories and possibly identify the nature of this anomaly. Techniques developed for the investigation of the Pioneer anomaly are applicable to the New Horizons mission. Analysis shows that anisotropic thermal radiation from on-board sources will accelerate this spacecraft by ～41×10^?10 m/s². We discuss the lessons learned from the study of the Pioneer anomaly for the New Horizons spacecraft.     

Ceramic ChemCam Calibration Targets on Mars Science Laboratory

The ChemCam instrument on the Mars Science Laboratory rover Curiosity will use laser-induced breakdown spectroscopy (LIBS) to analyze major and minor element chemistry from sub-millimeter spot sizes, at ranges of ～1.5–7?m. To interpret the emission spectra obtained, ten calibration standards will be carried on the rover deck. Graphite, Ti?metal, and four glasses of igneous composition provide primary, homogeneous calibration targets for the laser. Four granular ceramic targets have been added to provide compositions closer to soils and sedimentary materials like those expected at the Gale Crater field site on Mars. Components used in making these ceramics include basalt, evaporite, and phyllosilicate materials that approximate the chemical compositions of detrital and authigenic constituents of clastic and evaporite sediments, including the elevated sulfate contents present in many Mars sediments and soils. Powdered components were sintered at low temperature (800?°C) with a small amount (9?wt.%) of lithium tetraborate flux to produce ceramics that retain volatile sulfur yet are durable enough for the mission. The ceramic targets are more heterogeneous than the pure element and homogenous glass standards but they provide standards with compositions more similar to the sedimentary rocks that will be Curiosity’s prime targets at Gale Crater.     

Large Amplitude Oscillations in Prominences

Since the first reports of oscillations in prominences in the 1930s, there have been major theoretical and observational developments to understand the nature of these oscillatory phenomena, leading to the whole new field of the so-called “prominence seismology”. There are two types of oscillatory phenomena observed in prominences; “small-amplitude oscillations” (2–3 km?s^?1), which are quite common, and “large-amplitude oscillations” (>20 km?s^?1) for which observations are scarce. Large-amplitude oscillations have been found as “winking filament” in Hα as well as motion in the plane-of-sky in Hα, EUV, micro-wave and He 10830 observations. Historically, it has been suggested that the large-amplitude oscillations in prominences were triggered by disturbances such as fast-mode MHD waves (Moreton wave) produced by remote flares. Recent observations show, in addition, that near-by flares or jets can also create such large-amplitude oscillations in prominences. Large-amplitude oscillations, which are observed both in transverse as well as longitudinal direction, have a range of periods varying from tens of minutes to a few hours. Using the observed period of oscillation and simple theoretical models, the obtained magnetic field in prominences has shown quite a good agreement with directly measured one and, therefore, justifies prominence seismology as a powerful diagnostic tool. On rare occasions, when the large-amplitude oscillations have been observed before or during the eruption, the oscillations may be applied to diagnose the stability and the eruption mechanism. Here we review the recent developments and understanding in the observational properties of large-amplitude oscillations and their trigger mechanisms and stability in the context of prominence seismology.     

Satellite measurements of high latitude convection electric fields

This paper reviews the first results of satellite experiments to measure magnetospheric convection electric fields using the double-probe technique.The earliest successful measurements were made with the low-altitude (680–2530 km) polar orbiting Injun-5 spacecraft (launched August, 1968). The Injun-5 data are discussed in detail. The Injun-5 results are compared with the initial findings of the electric field experiment on the polar orbiting OGO-6 satellite (400–1100 km, launched June, 1969).In addition to electric fields, the Injun-5 spacecraft also measures electric antenna impedance and thermal and energetic charged particle densities. Knowledge of these parameters makes possible a detailed investigation of the operation of the electric antenna system. We report on this investigation and discuss errors attributed to sunlight shadows on the probes, wake effects, and other factors. The Injun-5 experiment can generally determine electric fields to an accuracy of about ±30 mV m^-1, and under favorable conditions, accuracies of ±10 mV m^-1 can be obtained.Reversals in the electric field at auroral zone latitudes are the most significant convection electric field effect discovered in the Injun-5 data. Electric field magnitudes of typically 30 mV m^-1, and sometimes 100 mV m^-1, are associated with reversals. Electric field reversals occur on 36% of auroral zone traversals, at about 70° to 80° invariant latitude, at all local times, and in both hemispheres. The latitude of a reversal often changes markedly on time scales less than 2 h. Electric potentials of greater than 40 keV are associated with these high latitude electric fields. Reversals occur at the boundary of measurable intensities of >45 keV electrons and are coincident with inverted V type low energy electron precipitation events. In almost all cases the E×B/B ² plasma convection velocities associated with reversals are directed east or west, with anti-sunward components at higher latitudes and sunward components at lower latitudes. Maximum convection velocities are typically 1.5 km s^-1 and ordinarily occur at the auroral zone near the reversal.Two extreme (and many intermediate) configurations of anti-sunward plasma convection have been observed to occur on the high latitude side of electric field reversals: (1) Ordinarily, >0.75 kms^-1 convection is limited to narrow (5° INV wide) zones adjacent to the reversal. (2) For 14% of reversals >0.75 km s^-1 anti-sunward convection has been observed across the entire polar cap along the trajectory of the Injun-5 spacecraft. A summary pattern of >0.75 km s^-1 polar thermal plasma convection is presented.Electric field measurements from the OGO-6 satellite have substantiated many of the initial Injun-5 observations with improved accuracy and sensitivity. The OGO-6 detector revealed the persistent occurrence of anti-sunward convection across the polar cap region at velocities (<0.75 km s^-1) not generally detectable with the Injun-5 experiment. The OGO-6 observations also provided information indicating that the location of the electric field reversal shifts equatorward during periods of increased magnetic activity.The implications of the electric field measurements for magnetosphericand auroral structure are summarized, and a list of specific recommendations for improving future experiments is presented.     

Energetic Hydrogen and Oxygen Atoms Observed on the Nightside of Mars

We present measurements of energetic hydrogen and oxygen atoms (ENAs) on the nightside of Mars detected by the neutral particle detector (NPD) of ASPERA-3 on Mars Express. We focus on the observations for which the field-of-view of NPD was directed at the nightside of Mars or at the region around the limb, thus monitoring the flow of ENAs towards the nightside of the planet. We derive energy spectra and total fluxes, and have compiled maps of hydrogen ENA outflow. The hydrogen ENA intensities reach 10⁵ cm⁻² sr⁻¹ s⁻¹, but no oxygen ENA signals above the detection threshold of 10⁴ cm⁻² sr⁻¹ s⁻¹ are observed. These intensities are considerably lower than most theoretical predictions. We explain the discrepancy as due to an overestimation of the charge-exchange processes in the models for which too high an exospheric density was assumed. Recent UV limb emission measurements (Galli et al., this issue) point to a hydrogen exobase density of 10¹⁰ m⁻³ and a very hot hydrogen component, whereas the models were based on a hydrogen exobase density of 10¹² m⁻³ and a temperature of 200 K predicted by Krasnopolsky and Gladstone (1996). Finally, we estimate the global atmospheric loss rate of hydrogen and oxygen due to the production of ENAs.     

High Velocity Outflows in AGNs Observed with Gratings

Several Active Galactic Nuclei (AGNs) have been reported to harbor fast outflows exceeding 10,000 km?s^?1, which are detected mostly in their low-resolution CCD X-ray spectra. Only few, however, were detected with high-resolution grating spectrometers. Most of the grating detected outflows have been observed multiple times. In these cases, the absorption spectrum changes are indicating that variability is common among these high-velocity winds. In this paper we revisit the grating observations of PG?1211+143, and PDS?456, and report preliminary results on 4C?74.26. We discuss the spectral variability of the first two sources and its implications to the outflows.