共查询到20条相似文献,搜索用时 109 毫秒
1.
针对9310钢研究了试验参数对疲劳小裂纹门槛值测试结果的影响,结果表明,对于9310高强钢采用恒Kmax/升Kmin方法进行小裂纹门槛值试验时,规范化的应力强度因子梯度Ck和Δα值的选取对门槛值的影响很小,当Kmax在线弹性范围内选取时,由于裂尖过程区的断裂机制未发生变化,Kmax的选取对门槛值测试结果也基本没有影响。 相似文献
2.
3.
通过断裂性能试验确定了某型直升机部件金属材料的断裂韧性和裂纹扩展门槛值,采用多元线性回归方法拟合得到裂纹扩展速率方程的材料常数。采用不同的裂纹分析方法进行了损伤容限分析。研究结果表明:对此型直升机部件的金属材料来讲,应力强度因子变程门槛值对应的应力比上截止限取0.7是合理的;低于安全疲劳极限的小载荷对裂纹扩展寿命有较大影响,尤其是按安全疲劳极限截除小载荷对裂纹扩展寿命的影响是非常显著的,当截除标准低于0.8倍的安全疲劳极限时,裂纹扩展寿命的差别不是很显著。 相似文献
4.
对AZ31B镁合金母材及其电子束焊接接头疲劳裂纹扩展速率进行研究,测试缺口位于母材、焊缝、热影响区(HAZ)时3组试验的裂纹扩展门槛值及扩展速率,并对3种试样疲劳裂纹扩展断口进行SEM分析.结果表明:缺口位于焊缝的裂纹扩展门槛值高于母材及HAZ,且疲劳裂纹扩展速率小于母材及HAZ.AZ31B镁合金母材及HAZ疲劳裂纹扩展断口都呈现河流状花样,为准解理脆性断口;焊缝的疲劳裂纹扩展断口中有许多撕裂棱、韧窝,表现出一定韧性,断口为以脆性为主的韧-脆混合断裂;随着裂纹扩展速率增大,三者断口中的解理台阶变粗大,疲劳条带变宽. 相似文献
5.
缺陷容限设计方法充分考虑直升机的特点,将损伤容限设计思想巧妙地应用于直升机的设计中,通过缺陷容限值保证关键动部件的服役安全。本文采用疲劳极限反推的方法测试了三种尺寸的缺陷容限门槛值,分别采用有限元法和Y.Murakami公式计算缺陷容限门槛值,结果表明:含有265μm,374μm,480μm缺陷尺寸的三种试件缺陷容限门槛值基本相同;缺陷容限门槛值明显低于长裂纹门槛值,采用长裂纹门槛值作为缺陷容限门槛值会导致偏于危险的结果;有限元法与Y.Murakami公式应力强度因子计算结果非常接近,Y.Murakami公式计算结果略低于有限元法。 相似文献
6.
7.
基于三维裂纹特征,本文提出了一种测量孔边角裂纹近门槛区疲劳裂纹扩展速率及门槛值的实验方法。为了得到真实的裂纹形状变化规律,首先针对具体试样用勾线方法建立其“b-a”标定曲线。参照门槛值的标准测试方法,本文仅需测量“a”方向裂纹尺寸,然后用标定曲线换算共相应的“b”方向尺寸。这样我们就可以得到关于“a”和“b”的两组数据,而这两个方向代表孔边角裂纹特征方向。通过分别对30CrMaSiNi2A和2024T3材料的实测研究,证明本文提出的测试方法是可行的。在实验数据基础上,进行了结果的统计对比,得出:1.“a”和“b”方向的近门槛区疲劳裂纹扩展速率及门槛值基本一致;2.孔径大小对实验结果没有影响。;3.同样厚度情况下,孔边角裂纹试样的近门槛区疲劳裂纹扩展速率编高,而门槛值相应较小。 相似文献
8.
9.
1.疲劳裂纹起始扩展门槛值(△K_(th))的概念 人们通常提到的疲劳裂纹扩展门槛值△K_(th)是在裂纹扩展过程中不断下降△K,使裂纹扩展不断减慢,直至停止扩展时所对应的△K值。它由降K程序测定,试验方法见文献。达到△K_(th)时裂纹前缘塑性区很小,在厚度和应力比一定的条件下,△K_(th)是材料常数。然而,在构件承受变幅交变载荷作用时,某级载荷使裂纹尖端产生应力强度因子K_(fmax),对应 相似文献
10.
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:3,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
13.
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
14.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
15.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
16.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
17.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
18.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献
19.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献