共查询到19条相似文献,搜索用时 62 毫秒
1.
高室压脉冲火箭发动机由于使用差动式可移动喷注器,能够得到比供给压强高得多的燃烧室压强.为了分析其工作特性,建立了单组元脉冲火箭发动机挤压喷注、燃烧、排气过程的集总参数模型,以硝酸羟铵(HAN)基作为单组元推进剂,采用四阶龙格-库塔法对模型进行求解.分别从喷注器喷孔面积、喷注器差动面积比、喷管喉部面积、喷注器行程等方面分析并总结了结构参数对单组元高室压脉冲发动机性能的影响规律及影响程度.结果表明:计算模型能反映发动机的实际工作过程,其中,喷注器行程对燃烧室平均压强和平均比冲的影响最大,平均推力则对喷管喉部面积的变化最为敏感,上述两个结构参数是发动机优化设计时的首要考虑因素;其他结构参数对发动机也存在不同程度的影响,可以作为次要因素来考虑. 相似文献
2.
为了更准确地预估含金属燃料固体火箭发动机的燃烧室压强,在压强计算中考虑两相流的影响,从一维两相喷管流动的求解出发,通过两相平衡流模型、两相常滞后模型、两相等温流模型、颗粒定温模型等模型的简化,分别推导不同模型下喷管中两相混合物的流量计算公式,再把流量公式应用到发动机零维内弹道理论中,推导并简化得到零维燃烧室平衡压强的计算公式。把压强公式用于HTPB推进剂固体火箭发动机和铝冰固体火箭发动机的燃烧室压强计算,结果表明,当固体推进剂中金属含量较高时(如铝含量为21%的HTPB推进剂发动机),用传统零维燃烧室压强公式预估的压强与实验误差较大,而使用合适的两相流模型和对应的零维燃烧室压强计算方法,在HTPB发动机中,能把压强预估结果与实验的误差降低到6%以内。如果使用多维内流场计算的方法,燃烧室压强预测结果的误差将下降到2.5%以内。结论发现在含金属固体火箭发动机的燃烧室压强计算中,考虑两相流的影响是必要的,而使用两相流修正后的零维燃烧室压强计算公式能够快速、较准确地预估这些发动机的燃烧室压强。 相似文献
3.
4.
为探索燃气温度与燃烧室工作压强对固体火箭发动机喷管阻尼特性的影响,同时为了对冷流试验的改进及不稳定燃烧研究提供相应的理论指导,基于Buffum冷流试验发动机的二维模型,利用脉冲衰减法,开展喷管阻尼特性数值仿真计算。结果分析表明燃气温度对喷管阻尼有很大影响,而燃烧室工作压强对其几乎没有影响。燃气温度越高,切断脉冲后,压力振荡衰减越快,即喷管阻尼衰减系数越大;不同工作压强下,切断脉冲后,压力振荡衰减速度几乎不变,即发动机喷管阻尼衰减常数几乎不变。 相似文献
5.
6.
建立了固液混合火箭发动机的仿真模型和相应的单目标和多目标优化模型,编制了系统仿真程序;采用差分进化算法针对不同的优化目标对发动机的参数进行优化;针对挤压式系统建立了质量模型,在优化过程中考虑了主要部件结构质量对发动机性能的影响;针对固液发动机常用的侧面燃烧药柱编制了内弹道计算程序。以药柱几何参数、氧化剂流量、燃烧室平均工作压强和喷管扩张比等参数为设计变量,对发动机平均比冲、总质量、关机时飞行速度和密度比冲等性能参数进行优化,在Pareto分析的基础上选择了氧化剂流量、燃烧室平均工作压强和喷管扩张比对发动机性能的影响作了深入研究;最后对某型固液发动机进行了优化分析。 相似文献
7.
高室压脉冲推力器使用可移动的喷注器,能够得到比供给压强高得多的燃烧室压强。为了分析其工作特性,建立了单组元脉冲推力器挤压和排气过程的数学模型,以硝酸羟铵(HAN)基单组元推进剂为例,采用四阶龙格-库塔法进行了求解。结果表明,燃烧室最大压强和平均压强都大于推进剂入口压强,而燃烧室内近似等容的燃烧过程是压强升高的原因。与所用推进剂、平均推力和面积比都相同的常规推力器相比较表明,脉冲推力器的真空比冲提高5 s,而喷管喉部面积减小89%,若两者喷管出口面积相同,则脉冲推力器的比冲将提高31.5%。 相似文献
8.
9.
10.
隔舱式双脉冲发动机第Ⅱ脉冲点火过程数值仿真 总被引:3,自引:2,他引:1
基于计算流体力学和相关点火理论,对双脉冲发动机第Ⅱ脉冲点火瞬态过程的流场进行了数值分析,并进行了发动机第Ⅱ脉冲点火试车试验。结果表明:在隔板打开前,第Ⅱ脉冲燃烧室高压区的位置由燃烧室前端向隔板移动,压强沿燃烧室径向变化较小,沿轴向变化较大,燃烧室头部和尾部近壁面区域一直处于低温;6 ms时隔板打开,第Ⅱ脉冲燃烧室压强下降05 MPa,药柱内孔前后端压强差波动剧烈,药柱内孔前端温度场下降600 K,而其他区域温度变化较小。隔板打开后,沿隔板下游第Ⅰ脉冲燃烧室轴线形成带状高温区,第Ⅰ脉冲燃烧室头部和尾部依次出现压强峰值,第Ⅰ脉冲燃烧室压强在18 ms时达到稳定,而温度在25 ms时达到稳定。试验测得的第Ⅰ、Ⅱ脉冲燃烧室压强-时间曲线和仿真结果吻合较好,表明该仿真方法具有一定的准确性。 相似文献
11.
12.
富氧补燃循环发动机启动过程 总被引:1,自引:0,他引:1
启动过程是液体火箭发动机研制中的重点和难点,解决大推力补燃循环发动机启动问题的主要措施应为:通过控制预燃室的燃料流量以有效地将预燃室的组元比控制在合理的范围内,并可以控制发动机的启动速率;燃烧室点火时预燃室应有较高的压力,同时应通过推力室燃料路的节流来减小燃烧室压力的上升速率;对于自身启动发动机,较高的入口压力有利于发动机启动。这些措施解决了富氧补燃循环发动机的启动问题,可供同类发动机的研制借鉴。 相似文献
13.
为探究液氧/煤油液体火箭发动机气液同轴喷嘴模型燃烧室具有良好稳定性的原因,采用非稳态雷诺平均(URANS)方法数值研究了其燃烧不稳定性和声学特征。两相燃烧条件下,燃烧室压力振荡幅值约为室压的10%左右、最大不超过25%,且以纵向和横向振型为主。一周六径隔板对横向振型具有很强的抑制作用,但对纵向振型影响较小。与液-液撞击式液氧/煤油发动机模型燃烧室相比,本文研究的燃烧室中煤油液滴没有发生超临界蒸发现象,第三邓克尔数较小,诱发燃烧不稳定性的激励源较弱。进一步通过数值定容弹激发了燃烧室多模态声学特征压力振荡,并得到了其振荡特征频率、幅值和衰减率。结果表明,气喷嘴具有四分之一波长喷嘴特征,能显著减小目标振型的幅值,而集气腔对纵向振型具有很强的抑制作用,同时对其他振型也有程度不同的抑制效果。因此,较弱的燃烧不稳定性激发机制以及隔板、气喷嘴和集气腔对纵向和横向振型很强的抑制作用,使得该液氧/煤油发动机气液同轴燃烧室具有很好的稳定性。 相似文献
14.
Alexey Gennadievich VOROBYEV Svatlana Sergeevna VOROBYEVA Lihui ZHANG Evgeniy Nikolaevich BELIAEV 《中国航空学报》2019,32(2):253-262
This paper presents a method of thermal state calculation of combustion chamber in small thrust liquid rocket engine. The goal is to predict the thermal state of chamber wall by using basic parameters of engine: thrust level, propellants, chamber pressure, injection pattern, film cooling parameters, material of wall and their coating, etc. The difficulties in modeling the startup and shutdown processes of thrusters lie in the fact that there are the conjugated physical processes occurring at various parameters for non-design conditions. A mathematical model to predict the thermal state of the combustion chamber for different engine operation modes is developed. To simulate the startup and shutdown processes, a quasi-steady approach is applied by replacing the transient process with time-variant operating parameters of steady-state processes. The mathematical model is based on several principles and data commonly used for heat transfer modeling: geometry of flow part, gas dynamics of flow, thermodynamics of propellants and combustion spices, convective and radiation heat flows, conjugated heat transfer between hot gas and wall, and transient approach for calculation of thermal state of construction. Calculations of the thermal state of the combustion chamber in single-turn-on mode show good convergence with the experimental results. The results of pulsed modes indicate a large temperature gradient on the internal wall surface of the chamber between pulses and the thermal state of the wall strongly depends on the pulse duration and the interval. 相似文献
15.
High combustion temperatures and long operation durations require the use of cooling techniques in liquid propellant rocket engines (LPRE). For high-pressure and high-thrust rocket engines, regenerative cooling is the most preferred cooling method. Traditionally, approximately square cross sectional cooling channels have been used. However, recent studies have shown that by increasing the coolant channel height-to-width aspect ratio and changing the cross sectional area in non-critical regions for heat flux, the rocket combustion chamber gas-side wall temperature can be reduced significantly without an increase in the coolant pressure drop. In this study, the regenerative cooling of a liquid propellant rocket engine has been numerically simulated. The engine has been modeled to operate on a LOX/kerosene mixture at a chamber pressure of 60 bar with 300 kN thrust and kerosene is considered as the coolant. A numerical investigation was performed to determine the effect of different aspect ratio and number of cooling channels on gas-side wall and coolant temperatures and pressure drop in cooling channels. 相似文献
16.
17.
由喷嘴连接的燃烧室到供应系统压力振荡传递过程研究 总被引:4,自引:2,他引:2
为了研究在压力振荡由液体火箭发动机燃烧室传递到供应系统的过程中喷嘴所起的作用,从理论上分析了压力振荡由燃烧室到供应系统通过喷嘴的传递过程,推导了振荡传递过程的传递函数.讨论带有各种喷嘴的供应系统的动态特性,对供应系统管路长度、燃烧室压强、喷嘴种类、喷嘴压降及喷嘴结构尺寸对燃烧室压力振荡引起供应系统压力振荡的影响进行了计算,得到了喷嘴以及工况参数在传递过程中的影响规律. 相似文献
18.
《中国航空学报》2021,34(2):432-440
Reusable rocket engines are the core components of reusable launch vehicles, and have thus become a major focus of aerospace engineering research in recent years. In practice, subsystem design is based on the overall index allocation of an engine; therefore, a multidisciplinary optimization approach is necessary. In this study, design of a reusable methane/liquid oxygen (LOX/CH4) rocket engine with a gas generator cycle was investigated using multidisciplinary optimization. Two parameters were chosen as design variables: pressure and fuel mix ratio of the main combustion chamber. Optimization objectives were specific impulse, structural mass, and life cycle cost of the reusable rocket engine, and constraints were assigned to each discipline according to rocket design requirements. Then, an optimization model was developed, and optimal design parameters were acquired for the LOX/CH4 rocket engine. The proposed method is effective for designing the index allocation of reusable rocket engines and takes into account the multidisciplinary nature of complex systems. 相似文献
19.
影响液体火箭发动机比推力的因素 总被引:1,自引:0,他引:1
介绍液体火箭发动机采用大比推力对提高导弹经济性的作用,论述推进剂性质,燃烧室压力,氧化剂剩余系数对液体火箭机动机比推力的影响及选用范围。 相似文献