共查询到20条相似文献,搜索用时 484 毫秒
1.
2.
军用飞行器航迹规划综述 总被引:66,自引:7,他引:66
介绍了军用飞行器航迹规划的基本概念,航迹规划与任务规划的关系,国内外研究现状,存在的问题,论述了航迹规划的基本要求,如导航要求,突防要求,飞行器性能要求及战略和战术要求,最后分析了航迹规划需要解决的威胁建模,航迹规划算法和轨迹跟踪控制等关键技术。 相似文献
3.
4.
5.
6.
对于应用卫星导航的民用航空运行而言,电离层是一种最为复杂的导航误差影响因素。由于电离层存在模型复杂、异常扰动和闪烁、电离层风暴的特性,尤其在太阳活动期间,可对民航导航带来致命性的影响,影响航空正常运行,国际上针对消除电离层误差提出了单一模型、相对定位以及广域增强等方法,目前国际民航组织也在开展电离层数据收集和构建区域电离层模型的工作。针对电离层形成原因与特性、消除电离层手段、电离层对民用航空导航的影响以及相应的解决措施,提出了民用航空消除电离层误差的方法和设想。 相似文献
7.
舰载的高精度惯性导航系统中,重力误差补偿的精度与导航的精度息息相关。长航时舰载导航系统,与短航时惯性导航系统相比,重力扰动随时间积累对导航精度的影响更加明显,因此不能再用简单的重力模型对重力进行近似,而需要对重力扰动误差进行补偿。本文针对舰载高精度惯性导航,理论上推导了重力扰动误差对惯性导航精度的影响,并以北向单通道模型对重力扰动误差与水平定位精度的解析关系式进行验证;进而用simulink仿真验证解析关系式的正确性,并在不同条件下进行了仿真。仿真结果表明:静态条件下,20小时以上的长航时导航中,北向或东向重力扰动分量每增加10mgal时,对应位置误差范围约增加130m。 相似文献
8.
针对当前海态巡航飞行试验末段外测无法跟踪测量的实际问题,基于现有脱靶量测量系统,建立了利用某脱靶量测量数据到发射系的转换模型。此模型将脱靶量测量数据统一到发射系航迹中,有利于航迹分析工作。并建立了转换结果的误差估计模型,误差模型充分考虑了脱靶量测量误差、靶船定位误差以及靶船航向角误差。利用仿真数据对转换模型及误差模型进行了计算验证。结果表明,位置误差满足精度要求。该方法对延拓外测处理时段具有积极意义。 相似文献
9.
根据高超声速飞行器导航的主要需求,针对高动态飞行条件下可能出现的卫星导航信号跟踪丢失等问题,本文设计了基于卫星观测值在线补偿的组合导航方法,该方法可在GPS导航接收机失锁的情况下,基于预存卫星星历外推模型和卫星信号误差模型,在线重构虚拟卫星导航观测值并补偿由信号失锁导致的组合滤波器发散情况,从而确保飞行器组合导航的精度。结合助推—滑翔高超声速飞行器航迹对该方案进行了仿真验证,结果表明,该方案能够在助推—滑翔高超声速飞行器强动态条件下确保卫星导航数据输出的连续性,在一定程度上克服了卫星导航信号丢失带来的不利影响,确保高超声速飞行器GPS/捷联惯导组合导航的基本导航定位性能。 相似文献
10.
针对混合动力复合翼飞行器巡航模式下空中停车后无动力应急迫降(VTOL)问题,提出在线航迹规划与制导方法。根据复合翼空中停车时初始位置/航向不确定散布,发展一套满足动力学约束、终端约束的三维航迹在线规划方法:利用几何规划方法快速生成扩展Dubins二维航迹,再根据下滑性能约束进行三维扩展。针对低速无动力下滑航迹跟踪更易受风干扰以及三维航线分段连接处曲率不连续的特性,发展一种基于非线性模型预测控制的三维制导算法。将纵横解耦的制导律嵌入到预测模型框架内,跟踪误差、外界风扰动、航迹曲率不连续等非线性因素则通过系统输出建立目标约束,其后利用滚动优化实时求解制导指令。最后对航迹在线规划方法与三维制导律的适用性进行仿真分析与验证,结果表明所提出的航迹规划方法适用于不确定初始位置/航向散布的应急迫降在线规划,所提的制导算法具备抵抗风扰、提高三维制导精度的能力。 相似文献
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:3,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
13.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
14.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
15.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
16.
17.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献
18.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献
19.
Wu Xianyu Li Xiaoshan Ding Meng Liu Weidong Wang Zhenguo 《中国航空学报》2007,20(6):488-494
In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances. 相似文献
20.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献