共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
飞机完成外挂吊舱的改装后,会引起其气动特性的变化,进而影响其飞行性能和操稳特性。以某双发轻型通用飞机为研究对象,在其机头处挂装光电吊舱、机腹处挂装SAR雷达吊舱,利用CFD技术获得外挂吊舱后飞机的气动数据,并计算改装后飞行性能的变化,分析改装对操稳特性的影响。结果表明:改装后飞机的起降距离、爬升率、航程航时等飞行性能指标有所降低,但对飞行品质的影响较小。研究结果可以指导飞机吊舱加改装,并可作为适航取证和后续试飞试验工作的参考。 相似文献
3.
4.
基于代理模型的机载吊舱气动与隐身一体化设计方法 总被引:1,自引:0,他引:1
考虑雷达隐身要求的机载吊舱初步设计时,存在载机-吊舱组合体RCS计算复杂度高的问题。为此,本文构造了用于计算RCS的代理模型,并基于此代理模型以吊舱横截面积、吊舱对载机的气动特性影响量和飞机与吊舱组合的RCS为优化目标,用评价函数法构造吊舱外形设计的多目标优化模型,并用复合形法求解该模型的设计参数。按该参数设计的吊舱外形能使载机在挂载吊舱后气动阻力系数与RCS增量均保持较低的水平,同时可保持吊舱较大的装载截面。研究结果表明,本方法在吊舱的初步设计阶段对设计参数的选取具有较好的指导意义。 相似文献
5.
6.
7.
在飞机设计与研制过程中,通过气动参数辨识建立可靠的飞行动力学模型非常重要。传统的气动参数辨识工程算法,诸如极大似然法,需要给出合理的飞行动力学模型以及待辨识参数的初值。基于传统神经网络的气动参数辨识可以避免飞行动力学建模过程,这种方法需要通过增量法、导数法间接地从神经网络提取气动参数。本文提出了一种基于物理信息神经网络的飞机气动参数辨识方法,可将含待辨识参数的飞行动力学模型作为正则项加入损失函数,直接辨识得到气动参数。该方法可以显著减少建模数据需求,也能提高建模精度。飞行仿真数据验证结果表明,该方法的无噪声、含2%噪声仿真数据,纵向飞行状态空间模型辨识最大相对误差分别为1.80%、4.64%,表明了基于物理信息神经网络的飞机气动参数辨识方法具有可行性,并对含噪声的飞行数据具有泛化性。 相似文献
8.
飞机积冰后若干飞行力学问题综述 总被引:5,自引:2,他引:3
回顾飞机积冰后若干飞行力学问题研究的历史与现状,着重介绍了积冰飞机气动数据的获取途径、积冰飞机飞行力学建模与飞行仿真、积冰对飞机稳定性和操纵性的影响以及积冰对飞机飞行性能的影响.在已有飞机积冰后飞行力学问题研究的基础上,提出了飞机积冰后飞行力学问题研究领域需要解决和关注的若干问题,包括通过数值模拟方法获取积冰飞机的气动数据、完善积冰对飞机气动导数影响的计算模型以及加强平尾失速方面的研究.今后需要进一步对模拟冰风洞、数值模拟方法和平尾失速进行研究,并获取更多实验数据. 相似文献
9.
提出了一种根据降雨条件、飞机特征和飞行状态计算雨滴撞击飞机产生附加作用力和力矩的方法,研究了降雨对飞机气动特性的影响,建立并线化分析了降雨气象条件下飞机的运动数学模型。在此基础上,以波音747为例,进一步研究了不同强度降雨对飞机纵向飞行品质的影响。结果表明,降雨将导致飞机的短周期模态特性变差,长周期模态阻尼比略有增加,降雨率较大时,飞机的纵向飞行品质等级降低。 相似文献
10.
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:3,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
13.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
14.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
15.
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
16.
17.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
18.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
19.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
20.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献