无人机机动轨迹跟踪系统设计

对无人机机动飞行轨迹跟踪系统的内环姿态控制律和外环轨迹跟踪控制律两部分分别进行了设计。利用非线性动态逆方法设计了内环姿态控制律。外环轨迹跟踪控制律采用逆动力学前馈加模糊反馈的控制结构,提高系统对飞行条件及期望轨迹剧烈变化时的跟踪精度。仿真结果表明,所设计的系统能够控制无人机精确跟踪指定的机动轨迹,且相对于固定增益系统具有更好的鲁棒性。     

Phase-Frequency Detection in Sampled Phase-Locked Frequency Mlultipliers

Phase-locked high-frequency multipliers which do not have powergreedy frequency dividers in the feedback loop, but which do have a sample-and-hold circuit as a phase detector are hard to design, due to conflicting requirements which determine the choice for loop gain and loop bandwidth. A circuit is described that acts as a frequency control if the loop is not locked and as a phase control once the loop can be locked. The loop filter has to be optimized for the locked condition only, and the allowable preset error is more than 80 percent of the sample frequency. The circuit also indicates whether the oscillator frequency is an odd or an even multiple of the sample frequency. Pull-in is at least an order of magnitude faster than with phase control alone.     

Nonlinear adaptive and sliding mode flight path control of F/A-18 model

The question of inertial trajectory control of aircraft in the three-dimensional space is discussed. It is assumed that the nonlinear aircraft model has uncertain aerodynamic derivatives. The control system is decomposed into a variable structure outer loop and an adaptive inner loop. The outer-loop feedback control system accomplishes (x,y,z) position trajectory and sideslip angle control using the derivative of thrust and three angular velocity components (p,q,r) as virtual control inputs. Then an adaptive inner feedback loop is designed, which produces the desired angular rotations of aircraft using aileron, elevator, and rudder control surfaces to complete the maneuver. Simplification in the inner-loop design is obtained based on a two-time scale (singular perturbation) design approach by ignoring the derivative of the virtual angular velocity vector, which is a function of slow variables. These results are applied to a simplified F/A-18 model. Simulation results are presented which show that in the closed-loop system asymptotic trajectory control is accomplished in spite of uncertainties in the model at different flight conditions.     

Signal-to-Noise Ratio of Arbitrary Power-Series Nonlinear Amplifier

A general analysis of the effect of an arbitrary power-series nonlinear amplifier followed by a coherent mixing device on signal-to-noise ratio (SNR) is performed. An expression is derived for the improvement factor which is defined as the logarithm of the ratio of the output SNR to the input SNR. This expression is applicable to the coherent amplitude detector and phase locked loop as well as noncoherent amplifier by appropriate selections of the detection angle. Moreover, the improvement factor can be obtained for noise with an arbitrary amplitude distribution. To demonstrate the applicability of this analysis, the improvement factors of the nonlinear amplifiers such as a power-law amplifier and a power-series amplifier with positive and negative discriminations are numerically calculated for the cases where the input noise amplitude distributions are Rician and triangular.     

Control design and closed-loop analysis of a switched-capacitorDC-to-DC converter

The theoretical and practical details involved in the control design and closed-loop analysis of a step-down switched-capacitor (SC) DC-to-DC converter are presented. The state-space averaging technique is applied to extract the small-signal dynamics of the power stage, and a graphical loop gain method is used to design the feedback compensation and analyze the closed-loop performance of an SC converter. The results of the control design and closed-loop analysis are substantiated by experiments using a prototype SC converter     

Control law design for transonic aeroservoelasticity

Existing computational transonic aeroservoelastic researches focus on directly coupling the structural dynamic equations, CFD solver and servo system in time domain, study the effect of the given feedback control laws on the responses of the aeroelastic system. These works have not involved the design of the flutter active control law. The non-linearity of transonic flow brings great difficulties to aeroservoelastic analysis and design. Recent research of the unsteady aerodynamic reduced order models (ROM) based on CFD provides a challenging approach for transonic aeroservoelastic analysis and design. Coupling the structural state equations with the aerodynamic state equations of the wing and the control surface based on the ROM, we construct a transonic aeroservoelastic model in state-space. Then the sub-optimal control method based on output feedback is used to design the flutter suppressing law. The study first demonstrates the open loop of the Benchmark Active Controls Technology (BACT) wing. The computational results of the CFD direct simulation method and the ROM analysis method are both agree well with the experimental data. Then both the closed loop time responses and the flutter results by ROM technique are compared with those of numerical aeroservoelastic simulation based on Euler codes to validate the correctness of the design method of the control law and aeroservoelastic analysis method. An increase of up to 20% of the speed index can be achieved by the control law designed by sub-optimal control method for this model.     

新一代歼击机超机动飞行的动态逆控制

 根据反馈线性化理论, 讨论了神经网络自适应非线性动态逆控制设计。首先根据时标分离原则, 采用动态逆方法设计快回路和慢回路控制器; 其次提出基于模型逆的神经网络非线性直接自适应控制方案, 设计一种在线神经网络用于补偿模型逆误差。仿真表明, 该控制方案具有较好的自适应能力和鲁棒性。     

数模转换器毛刺对光纤陀螺相关检测的影响分析

数模转换器(DAC)是全数字闭环光纤陀螺反馈通道的重要部件,DAC的毛刺特性会对光纤陀螺的调制解调结果产生影响.基于DAC中值毛刺特性建立了光纤陀螺反馈回路的非理想调制方波模型,分析了调制频率与本征频率不同时DAC毛刺在干涉信号中产生的各类周期干扰信号.利用周期干扰信号的Fourier级数推导出了DAC毛刺造成调制解调误差的数学模型,仿真分析了数模转换器毛刺的宽度、高度,光纤陀螺调制频率、本征频率及放大电路的增益带宽对陀螺解调误差的影响.最后,通过开环实验验证了DAC毛刺对光纤陀螺调制解调的影响.     

双周期分布式压电分支阻尼对失谐叶盘振动抑制作用分析

将压电分支电路引入失谐叶盘结构，形成机电耦合系统，给出了机电耦合系统动力学方程的推导过程，并从理论上研究了压电分支阻尼对失谐叶盘结构响应放大的抑制效果.通过构造双周期分布式压电分支电路，研究了双周期分布式压电分支阻尼对失谐叶盘结构的振动抑制效果，并与单周期压电分支电路进行了对比，对比结果显示压电分支阻尼（包括单周期压电分支阻尼以及双周期分布式压电分支阻尼）均能有效降低随机失谐叶盘结构的响应放大，其中双周期机电耦合系统响应放大因子统计分析结果小于1的概率在99.7%以上，基本消除了失谐叶盘结构的响应放大现象.通过合理地设计系统的双周期模式，能够获得比单周期更好的失谐响应放大抑制效果.此外，压电分支阻尼使得随机失谐叶盘结构的失谐“阈值”现象消失，提高了叶盘结构的失谐鲁棒性.      

再入机动飞行器的控制系统设计

基于再人机动飞行器机动控制特点，设计了两种反馈结构——过载反馈和姿态角反馈的姿控系统．并从输入反馈信号构成、系统回路设计、反馈系数确定及飞行弹道仿真结果等方面，对两种形式的姿控系统进行了比较。结果表明．过载反馈系统在再人机动飞行器的飞行控制中效果较好。     

航空发动机控制系统性能恢复设计:H_∞/PR

对于航空发动机这样一类状态及输出矩阵存在摄动的系统,提出了一种直接根据性能指标作为恢复的目标的性能恢复理论设计方法。首先进行具有稳定及性能鲁棒性的状态反馈的H∞控制设计,然后通过设计一个状态观测器使得上述状态反馈控制的特性得以恢复。     

柔性制造系统运行设计的自适应仿真研究

 把控制理论中的自适应控制策略应用到柔性制造系统仿真软件的开发中来,提出了自适应仿真思想用于柔性制造系统运行设计,在一定范围内解决了集成智能仿真环境中对柔性制造系统仿真结果的自动优化等问题,并对自适应仿真进行了展望。     

具有未知输入干扰的观测器设计

提出一种全阶比例积分观测器。该观测器包含有估计误差的比例和积分回路,可同时得到状态和未知输入估计。分析了比例积分观测器的结构和估计性能,给出并证明了其存在条件,由于存在条件弱于未知输入观测器,该比例积分观测器可以更广泛地应用于基于观测器的技术方案。通过一个飞行器线性化模型,进行了比例积分观测器设计。仿真结果表明,比例积分观测器的估计性能优于常规 Luenberger观测器     

直接力控制的特征结构配置法

以现代控制理论和飞行力学原理为基础，针对直接力控制器设计中存在的模态耦合问题，提出一种应用状态反特征结构配置进行解耦的方法，并出相应的公式。分析表明，用此方法对系统的极点和特征向量可以进行希望的配置。并能达到设计要求，同时仿真结果说明，用状态反馈特征结构配置法设计的控制系统比用线性二次型调节器（LQR）方法设计的控制系统解耦性能好，响应速度快，并且解决了输出反馈特征结构配置不能确保闭环系统稳定的问题。     

直升机着舰纵向下滑控制系统仿真研究

采用ＬＱＧ／ＬＴＲ方法设计了直升机着舰纵向下滑控制系统,其中包括建立直升机增广系统的数学模型,确定控制器的频域范围匐棒性边界条件,反馈回路的设计和回路传递函数在输出端的恢复。在给出该控制系统仿真框图的基础上,利用仿真软件进行数字仿真。最后,对仿真结果中直升机高度、速度随机－舰距离和时间的变化曲线进行了分析,得到了一些有工程应用价值的研究结果。     

具有环路复现特性的Luenberger观测器设计(二)

从一个一般的环路传递复现(Loop transfer recovery)条件出发,基于线性系统Luenberger函数观测器设计的一种参数化方法,给出了具有环路复现特性的Luenberger观测器设计的一种方法。该方法适用范围广,且具有较小的保守性。数值算例说明了共有效性。     

Two-State Feedback Loop Adaptive Arrays for Pulsed Interference Signals

A two-state feedback loop is presented which increases the effectiveness of an adaptive array in the presence of pulsed interference signals. In the case of the two-state feedback loop, one state permits the maximum adpative response, consistent with the loop stability, and is activated in the presence of an interfering pulse. During the other state, which is activated when the interfering pulse is off, the weights are frozen at the values reached at the end of the last interfering pulse and are maintained until the next disturbance occurs. It is shown that an adaptive array with the proposed two-state loops steers permanent minima in the direction of the interfering signals, irrespective of their duty cycle. The performance of a communication system protected by such an adaptive array improves significantly over one protected by a conventional adaptive array.     

FM Threshold Performance of the Frequency Demodulator with Feedback

The FM threshold performance of the frequency demodulator with feedback (FMFB) is experimentally optimized. Rules of thumb for the practical design of the FMFB with limiter in the loop are proposed. Such design rules provide for optimum FMFB threshold performance given specifications of the received signal. Equivalences among the FMFB, phase-locked loop, and limiter- discriminator offer some additional physical insight into the threshold-extending mechanism of the FMFB not presented by previous investigators.     

飞控系统模糊控制器设计及稳定性分析

建立了飞控系统的Ｔａｋａｇｉ－Ｓｕｇｅｎｏ（Ｔ－Ｓ）模糊模型;给出了设计模糊状态反馈控制器,保证闭环系统全局渐近稳定、具有一定衰减率稳定的两个充分条件;提出了采用线性矩阵不等式（ＬＭＩ）方法,将该充分条件转化为对线性矩阵不等式族寻求ＬＭＩ可行解的凸优化问题,得到了稳定性分析和模糊状态反馈控制器设计的新方法。仿真结果表明,所提出的设计方法方便有效,控制器鲁棒性好。     

Analysis of the linear amplifier/analog-digital converter interfacein a digital microwave receiver

An analysis of the relationship between a linear amplifier chain and an analog-to-digital converter (ADC) in a digital microwave receiver, with respect to sensitivity and dynamic range issues, is presented. The effects of gain, third-order intermodulation products and ADC characteristics on the performance of the receiver are illustrated and design criteria for the linear amplifier chain (given a specified ADC) are developed. A computer program is included which calculates theoretical receiver performance based on gain and third-order intermodulation product selections. Experimental results are also presented and compared with theoretical values