前缘剖面形状对80°／60°后掠双三角翼上涡流运动影响的数值模拟研究

采用上风高分辨率格式———通量差分分裂格式离散求解三维可压非定常薄层N S方程 ,数值模拟前缘剖面形状对 80°/60°后掠双三角翼上涡流运动的影响。计算模型包括尖前缘、菱形前缘、圆形前缘等三种不同前缘形状的机翼。计算结果表明 :三种不同剖面形状的前缘可以诱导产生不同的前缘分离 ,形成的各前缘剪切层的特点也不同。尖前缘机翼的边条翼涡和外翼涡合并点最靠前 ,其次为菱形前缘和圆形前缘的机翼。在大迎角情况下 ,三种机翼上的内翼涡发生破裂。圆形前缘机翼上的内翼涡破裂点比其它两种情况下破裂点的位置较靠前。涡的合并对二次涡的结构和特点也有显著的影响。     

An experimental investigation on static directional stability

A generic aircraft usually loses its static directional stability at moderate angle of attack (typically 20–30?). In this research, wind tunnel studies were performed using an aircraft model with moderate swept wing and a conventional vertical tail. The purpose of this study was to investigate flow mechanisms responsible for static directional stability. Measurements of force, surface pressure and spatial flow field were carried out for angles of attack from 0? to 46? and sideslip angles from ?8? to 8?. Results of the wind tunnel experiments show that the vertical tail is the main contributor to static directional stability, while the fuselage is the main contributor to static directional instabil-ity of the model. In the sideslip attitude for moderate angles of attack, the fuselage vortex and the wing vortex merged together and changed asymmetrically as angle of attack increased on the wind-ward side and leeward side of the vertical tail. The separated asymmetrical vortex flow around the vertical tail is the main reason for reduction in the static directional stability. Compared with the wing vortices, the fuselage vortices are more concentrated and closer to the vertical tail, so the yaw-ing moment of vertical tail is more unstable than that when the wings are absent. On the other hand, the attached asymmetrical flow over the fuselage in sideslip leads to the static directional instability of the fuselage being exacerbated. It is mainly due to the predominant model contour blockage effect on the windward side flow over the model in sideslip, which is strongly affected by angle of attack.     

双三角翼前缘剖面形状对涡运动的影响

采用数值模拟和理论分析相结合的方法,研究了前缘剖面形状对双三角翼涡运动的影响,分析了前缘剖面形状对三角翼、双三角翼涡运动影响的不同机理 :对三角翼,尖前缘可以形成组织最好的涡结构,但对于双三角翼,圆前缘生成的旋涡结构较靠近翼面,涡结构紧密,诱导能力较强,可以形成有利的涡涡干扰,使内翼涡通过剪切层向外翼涡输入涡量更加容易,合并涡变得更加稳定,推迟了涡破裂,而且由于涡较靠近翼面,因而可以产生较高的非线性涡升力,这同传统的认识是不一致的。     

后缘喷流对三角翼绕流影响的N-S方程数值分析

本文用拟压缩性方法求解不可压流雷诺平均拟压缩Ｎ－Ｓ方程组,对带有后缘喷流的三角翼粘性绕流进行了数值模拟,求解中采用了Ｂｅａｍ－Ｗａｒｍｉｎｇ隐式近似因子分解格式以及ＭＭＬ代数湍流模型。计算结果说明,后缘喷流使涡核压强降低,使涡核速度增大,从而对三角翼前缘分离涡有稳定作用,并能增大上翼面的负压值和下翼面的正压值,从而可以增加部分升力。计算结果还说明,喷口面积或喷流下偏会使上述作用增强。     

双后掠鸭翼气动特性的数值模拟

首先针对具有中等前缘后掠角梯形鸭翼的缺点提出双后掠鸭翼概念,然后分别对安装梯形鸭翼和双后掠鸭翼的近距耦合鸭式布局的气动性能进行数值模拟研究,分析影响双后掠鸭翼气动性能的流动机理。研究表明：在大迎角时,对于双后掠鸭翼,具有较大前缘后掠角的外翼段可以使鸭翼涡在涡核破裂后仍能形成稳定集中涡并保持较高的强度,增加鸭翼本身的失速迎角,并通过诱导作用改善机翼外翼段流场,进而提高全机大迎角性能,但在小迎角时会破坏鸭翼附着流或前缘气泡涡的发展,造成略微的升力损失。拥有较大失速迎角的双后掠鸭翼在小迎角时具有较大的可用偏度,可以增强布局的抬头控制能力。双后掠鸭翼在满足隐身约束的前提下,超声速阻力较小,具有较好的超声速性能。     

翼尖涡流场特性及其控制

大型运输飞机的尾涡系是诱发后继小型飞机空难的重要原因,需要有效的涡控制装置来削弱其强度.通过风洞实验,研究了翼型为NACA23016的矩形半机翼模型翼尖尾涡流动结构和控制方法.应用七孔探针空间流场定量测试技术研究了翼尖涡的流动结构,给出了翼尖尾涡在下游两倍弦长距离内的速度和压力场分布随迎角变化的规律.在机翼翼梢布置不同组合方式的翼梢涡扩散器,来控制翼尖涡.研究结果表明,正负90°和60°安装角的双翼梢涡扩散器可将翼尖涡涡核的静压增加60%以上.其旋涡强度削弱机理为:翼梢涡扩散器将集中的翼尖涡破碎分成两个或多个强度更弱的旋涡.在流体粘性的作用下,旋涡能量耗散更快,可有效地削弱翼尖尾涡的强度.     

涡襟翼振动对三角翼涡的影响

 <正> 1.引言 许多实验表明,用主动干扰的方式是控制分离的一个有效方法,而且可以把分离区从一死水区(或紊乱的区域)变成一个有序流动区域。二维流动实验还表明非定常机动可以较大地改变流动结构。三维流态显示表明强迫振动对集中涡的形成过程等有显著影响,并影响涡和物面之间的距离。目前对三维非定常流动特性,以及非定常干扰对机翼绕流中涡破裂等的作用尚未充分了解。 影响集中涡破裂的关键因素是沿涡轴方向的压力梯度。涡环量对破裂的影响是双向的,涡强过大易使涡破裂;涡强过小时涡结构松散,也易于破裂,甚至迅速耗散掉。从二维结果看,非定常强迫扰动可使涡的结构更紧凑、清晰,而且扰动可以改     

翼刀对双立尾／三角翼立尾抖振的影响

在北航的水槽和风洞中进行了加装翼刀的75°后掠双立尾／三角翼的立尾抖振实验,目的是研究翼刀对立尾抖振的影响。采用了流动显示、立尾表面动态压力测量、激光测立尾顶部加速度的实验来检验翼刀对立尾抖振减缓的效果。流动显示的实验结果表明三角翼前缘涡涡核从翼刀上方经过时,会提前破裂,这在一定程度上减弱了前缘涡。激光测立尾顶部加速度实验的结果表明,在28°到48°这段立尾抖振比较显著的迎角范围内,B1立尾位置的立尾抖振强度曲线比无翼刀的曲线数值上有明显的减小,抖振得到一定的改善。立尾表面动态压力的脉动强度也有明显的减小,频谱分析也能得到前缘涡提前破裂的结论,前缘涡的提前破裂起到了减缓立尾抖振作用。     

超音速细长梯形翼背风面流型

给出了前缘后掠６５°、双弧形剖面的细长梯形翼背风面流动显示结果。实验Ｍａｃｈ数为１．１０,１．５３,２．５３,３．０１和４．０１,攻角范围为５°～２５°。应用蒸汽屏、纹影和油流技术拍摄了空间和表面流型照片。蒸汽屏显示表明：在机翼背风面三角形区域的空间流型随法向攻角αＮ（在垂直于前缘的平面内流速与弦线间的夹角）和法向Ｍａｃｈ数ＭａＮ（来流Ｍａｃｈ数在垂直于前缘平面内的分量）变化,并可在αＮ和ＭａＮ为坐标的平面上划分出７种流型存在的区域。侧缘区有侧缘分离涡形成;后缘有尾涡拖出。从纹影照片与横截面上的蒸汽屏照片对照可获得机翼锥面激波位置随Ｍａｃｈ数的变化;以及激波－诱导分离线位置随Ｍａｃｈ数和攻角变化曲线。机翼表面油流谱显示出了主再附线、二次分离线、二次再附线和侧缘涡区。显示出的流型与其他有关实验和数值计算结果比较符合得很好     

Visualization and PIV study of wing-tip vortices for three different tip configurations

The planform, profile, and cross-sectional views of the wing-tip region of a half-wing model with an aspect ratio of 3.2 and three different wing configurations, namely, square-cut, simple fairing, and Whitcomb?s full winglet wing-tip, were visualized at various angles of attack using smoke-wire visualization technique. Visualization pictures clearly show that the wing-tip vortices at different angles of attack and wing-tip configurations had distinct formation and structure characteristics. A comparison of simple fairing and Whitcomb?s winglet configurations shows that the wing-tip vortices of the Whitcomb?s winglet configuration were reduced in strength and displaced outboard and upward, at least in the near-wake region. This resulted in an increased lift-to-drag ratio for the Whitcomb?s winglet configuration. The changes in the wing-tip vortex characteristics and the improved aerodynamic performance of the winglet were confirmed by Particle Image Velocimetry (PIV) measurements of the cross-flow velocity of the wing-tip trailing regions and the force measurement of the model.     

褶皱位置对蜻蜓滑翔翼气动性能的影响

改变昆虫翅膀的褶皱结构可以优化翼型的气动性能,有利于微型飞行器的气动设计。以蜻蜓翼作为参考,采用计算流体力学（CFD）的方法计算了攻角范围为0°~20°,雷诺数范围为700~2300时褶皱位于前缘、尾缘和中部位置时三种翼型的滑翔气动性能。结果表明:在不同攻角和雷诺数下,褶皱位于尾缘的翼型具有最大的升力系数和升阻比,滑翔气动性能最优;当雷诺数为1500,攻角为10°时,褶皱位于尾缘的翼型时均升力系数分别比位于前缘和中部的翼型提高了58%和82%,升阻比分别提高了49%和33%;这是由于尾缘褶皱中的涡起到了延缓前缘涡脱落的作用,使前缘涡更为集中,更贴近壁面。      

基于DES方法的三角翼激波-涡干扰流场数值模拟

采用基于Spalart-Allmaras湍流模型的脱体涡模拟（DES）方法,数值求解Navier-Stokes方程,模拟绕尖前缘三角翼的跨音速流动,并对三角翼上翼面的复杂激波-旋涡干扰流场进行了分析。与NASA兰利研究中心的NTF风洞实验结果对比分析表明,DES方法能很好地模拟跨音速三角翼上的旋涡流动。随着攻角由中度攻角增加到大攻角,支架附近的激波越来越强,对主分离涡的干扰作用越来越大,直至出现激波干扰导致的涡破裂。激波的形状、位置及涡破裂位置均与实验结果吻合良好。     

低雷诺数下50°后掠三角翼的旋涡流动

采用数值模拟和流动显示的方法研究了50°后掠角三角翼在低雷诺数下的旋涡流动,结果表明:低雷诺数下,非细长三角翼在5°攻角时就形成了稳定的前缘涡,较小攻角时前缘主涡就开始破裂,并观察到泡型和螺旋型两种旋涡破裂方式。另外,在一定的攻角范围内,前缘主涡的外侧又生成一对新的集中涡,构成双涡结构;随着攻角的增大,前缘涡涡核不断升高,主再附线向中心移动,二次分离区扩大。     

Investigation of Vortex Interaction in Canard-FSW Configurations Based on the Numerical Wind Tunnel Method

The vortex interference mechanism on low Reynolds number between the canard and main wing of the canard-forward sweep wing (Canard-FSW) configurations is simulated numerically by employing the numerical wind tunnel method. The variations of aerodynamic characteristics of Canard-FSW configurations with different positions of the canard are investigated, finding that the aerodynamic interference and mutual coupling effect between the canard and main wing have made great contributions to the lift and stability characteristics of the whole aircraft. Canard can radically improve the surface flow pattern of the main wing. And its own vortex can have a favorable interference on the main wing and can effectively control the airflow boundary layer separation. At small angles of attack, the aerodynamic characteristics are sensitive to the positions of the canard and the main wing, but at high angles of attack, the aerodynamic performances of the configuration are not only related to the shape of the canard (forward or backward), but also with the size of control force as well as the features of the vortices generated above the main wing and the canard. The different configurations and vortices are illustrated using the velocity vector, streamlines and pressure contours.     

低雷诺数仿生分离流翼型气动特性初探

为了探索适合低雷诺数微型飞行器的翼型形式,基于对自然界鸟类和昆虫滑翔飞行时翅膀形状的观察,设计出一种由前缘削尖平板和后缘圆弧翼型组合而成的仿生分离流翼型。数值研究结果表明,气流在削尖平板的前缘点强制分离,形成大范围低压分离流动,随后在后部圆弧翼上表面再附形成稳定低压涡流区,从而实现较高的气动效率和较强的抵抗大气湍流的能力。上削尖平板可以使流动分离点固定在削尖点。相对于单独平板,仿生分离流翼型的升力系数有大幅提高,迎角为4°时提高了112%。此外,仿生分离流翼型可以在较宽的迎角范围内（4°~20°）保持高升力,但是迎角增加,阻力也快速增大,因此小迎角情况下（小于4°）气动效率更优。      

细长翼绕流中的旋涡特性

 本文综述了细长翼绕流中由前缘分离形成的集中涡的各种运动特性。细长翼翼面上方的前缘集中涡是控制机翼绕流和影响机翼气动力特性的主要因素。为此本文详细介绍了前缘涡的形成及其基本流动结构;前缘涡的破裂现象及其对机翼气动力特性的影响;并给出前缘涡破裂的各种理论模型和它的估算方法。最后还简单介绍了绕流中旋涡之间的绕合现象和互相干扰的流动结构。     

Experimental and numerical investigation of threedimensional vortex structures of a pitching airfoil at a transitional Reynolds number

This research examines the vortex behaviors and aerodynamic forces in dynamic stall phenomena at a transitional Reynolds number(Re = 90000) using experimental and numerical approaches.Periodic sinusoidal pitching motion at two different reduced frequencies is used to achieve the dynamic stall of a NACA 0012 airfoil.Several leading edge vortices form and detach in the dynamic stall stage.The flow then quickly transitions to a full separation zone in the stall stage when the angle of attack starts to decrease.There is discrepancy between the phaseaveraged and instantaneous flow field in that the small flow structures increased with angle of attack, which is a characteristic of the flow field at the transitional Reynolds number.The interaction between the streamwise vortices in the three-dimensional numerical results and the leading edge vortex are the main contribution to the turbulent flow.In addition, the leading edge vortex that supplies vortex lift is more stable at higher reduced frequency, which decreases the lift fluctuation in the dynamic stall stage.The leading edge vortex at higher reduced frequency is strong enough to stabilize the flow, even when the airfoil is in the down-stroke phase.     

超声三速角翼背风区旋涡运动的数值模拟

本文采用杂交通量分裂的ＮＮＤ格式模拟了Ｍ∞＝１．９５、Ｒｅ＝９．５×１０５，α＝１０°、２０°的三角翼绕流流场，结果揭示了超声速旋涡沿其自身轴线的发展规律，当旋涡轴向速度为超声速且处于顺压区时，涡轴附近的横截面流线向外转，而由机翼前缘尖点处发出的截面流线向内卷，它们之间存在极限环。数值结果与张涵信的拓扑分析结果完全一致。     

Experimental investigation of influence of strake wings on self-induced roll motion at high angles of attack

The modern high performance air vehicles are required to have extreme maneuverability,which includes the ability of controlled maneuvers at high angle of attack. However, the nonlinear and unsteady aerodynamic phenomena, such as flow separation, vortices interaction, and vortices breaking down, will occur during the flight at high angle of attack, which could induce the uncommanded motions for the air vehicles. For the high maneuverable and agile air missile, the nonlinear roll motions would occur at the high angle of attack. The present work is focused on the selfinduced nonlinear roll motion for a missile configuration and discusses the influence of the strake wings on the roll motion according to the results from free-to-roll test and PIV measurement using the models assembled with different strake wings at a = 60°. The free-to-roll results show that the model with whole strake wings(baseline), the model assembled with three strake wings(Case A)and the model assembled with two opposite strake wings(Case C) experience the spinning, while the model assembled with two adjacent strake wings(Case B), the model assembled with one strake wing(Case D) and the model with no strake wing(Case E) trim or slightly vibrate at a certain "×"rolling angle, which mean that the rolling stability can be improved by dismantling certain strake wings. The flow field results from PIV measurement show that the leeward asymmetric vortices are induced by the windward strake wings. The vortices would interact the strake wings and induce crossflow on the downstream fins to degrade the rolling stability of the model. This could be the main reason for the self-induced roll motion of the model at a = 60°.     

三角翼涡破裂非定常特性实验研究

本文依据染色液流动显示结果,通过子波和频谱分析,探讨了70°三角翼前缘涡涡核轴向速度的变化规律及其子波特性、涡破裂位置的非定常特性,指出涡破裂点位置的变化属于低频高幅振荡,这主要是左右涡之间的相互作用造成的,当两个涡的时间平均涡破裂点位置彼此靠得更近时,相应的振荡就更大一些,此外本实验得到涡破裂位置振荡的折合频率在St=0.2以内.