共查询到20条相似文献,搜索用时 130 毫秒
1.
引言
翼面结冰是飞机飞行过程中经常可能遇到的现象,也是威胁飞机飞行安全性的一大因素.我国适航当局对民用飞机在结冰条件下的安全飞行制定了相关的条款,只有经过适航当局符合性验证的飞机,才能发放结冰条件下的合格许可.研究飞机结冰首先要确定冰型. 相似文献
2.
3.
非平衡凝固是过冷条件下水滴凝固过程的重要现象。本文针对飞机结冰过程过冷水滴的非平衡凝固效应,发展了改进的凝固特性预测模型及数值计算方法,并自行搭建了实验系统,开展了所建过冷水滴凝固模型与数值预测方法的实验验证。研究表明,所发展的改进模型可有效表征水滴过冷阶段的非平衡凝固效应,因而对冷水滴凝固速率的预测有较好的改进;当过冷度为0℃时,过冷模型退化为传统模型。基于所建方法,开展了过冷度及冷却条件对水滴凝固特性的影响分析,获得了不同条件下水滴凝固过程的温度分布及相界面变化特征。研究表明,过冷度越大或水滴尺度越小,凝固速率相对越高;在考虑非平衡凝固效应的条件下,过冷水滴凝固速率要高于不考虑非平衡凝固效应的工况。相关研究可为结冰热力学模型的改进,以及结冰特性的精细化预测提供参考。 相似文献
4.
针对飞机过冷水滴结冰的精细化预测需求,基于相变热力学与相变动力学相关理论,采用示差扫描量热法(DSC)、结冰风洞试验及微结构测试相结合的方法,研究了过冷水滴凝固过程的热力学机理及凝固组织特征。基于示差扫描量热法,研究了冷却速率及形核条件对结晶凝固特性的影响规律;基于结冰风洞试验开展了不同温度条件下冰相的宏观形貌及微结构特征研究。结果表明,过冷条件及冷却速率是影响过冷水滴结晶速率及结晶完善程度的重要因素。降温速率越大,结晶速率常数增大、结晶速率相应提高。同时,结晶峰变宽,结晶初始温度向低温方向移动,过冷效应相对显著;反之亦然。过冷度及冷却速率对冰相的宏观及微观形貌均有着重要影响。过冷度越大则相同时间内冷却速率越大,晶体生长过程越不充分,晶体不规则程度相对较高,同时晶粒密度变大、尺度变小,冰相表观透明度相对降低;反之,过冷度越小,则晶粒密度变小、尺度变大,冰相表观透明度相对较高。异相形核条件对加速结晶过程有重要促进作用,晶种的存在可有效加速二次结晶的触发,使过冷效应显著减弱。相关研究可为飞机结冰速率、冰相物理特征及冰形宏观形貌的精细化预测提供参考。 相似文献
5.
飞机在结冰条件下飞行时可能发生结冰,飞机一旦结冰,会对安全飞行带来较大的隐患,如何降低飞机结冰带来的危害已成为飞机设计研究的重点内容.通过FENSAP-ICE对机翼进行数值模拟,并通过改进Messinger结冰热力学模型模拟更加真实的飞行情况;分析不同飞行环境下,飞机结冰前后机翼气动特性的变化,同时针对机翼设计一套防除冰系统并验证其可行性.结果表明:飞行速度越大,机翼表面的局部水收集系数越大;环境温度会影响机翼结冰的类型和结冰厚度,机翼发生结冰时,其升力系数减小、阻力系数增大,机翼的气动特性受到严重的影响;设计的电热防冰系统可以有效地预防机翼表面结冰,也可以进行周期性除冰. 相似文献
6.
7.
8.
飞机结冰是动态冻结的过程,在微观上会形成类似多孔介质的孔隙结构,该微观结构直接影响结冰的物理特性,同时又因结冰条件的不同而呈现一定差异化。针对温度对飞机结冰微观特性定量影响这一难点问题,首先结合图像分割方法,提出结冰微观信息提取方法;其次,结合结冰微观形态的定量结果提出合理假设,建立结冰微观结构的三维数学模型,并提出计算密度的概念,以此作为衡量结冰内部孔隙分布特性的定量指标;最后,以风洞试验显微图像为对象,验证孔隙提取方法和微观结构数学模型的适用性与合理性,并开展了温度对孔隙分布和计算密度的定量影响研究,微观定量结果与宏观特性具有较高的一致性。本研究可以为结冰微观定量研究提供方法手段,为结冰物理现象及物理特性的深入认识提供定量依据。 相似文献
9.
10.
过冷大水滴动力学特性对结冰影响数值研究 总被引:1,自引:0,他引:1
对比常规水滴,过冷大水滴结冰对飞机气动性能和飞行安全具有更大的危害性。在常规水滴结冰过程数值模拟基础上,针对过冷大水滴条件下各种动力学特性及其对成冰过程的影响进行了数值研究。采用结构化网格和中心有限体积法求解 N-S 方程获得空气流场,用拉格朗日法求解水滴流场,基于改进的 Messinger 热力学模型完成结冰过程模拟;对于过冷大水滴,采用泰勒类比理论和水滴碰撞模型,对比分析了水滴动力学特性及其对结冰过程的影响;通过数值模拟获得了水滴 Langmuir D 分布的撞击特性及结冰计算结果,研究了水滴多尺度分布对成冰过程的影响规律。通过一些典型结冰算例的数值模拟,并与参考文献结果及实验数据的对比分析,说明了本文计算方法及计算模型模拟过冷大水滴结冰是可行和正确的。 相似文献
11.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
12.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
13.
14.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
15.
16.
航天器返回地球的气动特性综述 总被引:4,自引:0,他引:4
航天器返回地球的飞行过程中,气动特性是实现将宇宙飞行速度减到落地前速度、保证再入飞行得到有效控制以及再入防热安全可靠的关键因素。针对简单旋成体气动外形、半弹道式再入控制、烧蚀防热类返回航天器,综述了返回地球过程中变化的空气流域特性、航天器周围的气体绕流环境、空气与航天器作用产生的动力学与热效应等。系统地给出了该类航天器的再入气动特性参数与飞行性能的共性规律,包括:气动阻力与再入减速、气动升力与再入轨迹控制、配平攻角与飞行稳定性、气动加热与防热,以及再入过程中不同气动特性航天器、气象条件变化等对再入飞行性能的影响规律。为航天器开展返回飞行过程的跨流域气动性能工程研制提供设计参考。 相似文献
17.
Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis 总被引:2,自引:0,他引:2
GAO Hong-liang ZHANG Hui WANG Shu-juan 《中国航空学报》2007,20(1):75-80
Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved. 相似文献
18.
19.
Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters 总被引:1,自引:0,他引:1
ZHOU Hong-guo WEI Xiu-ying MAO Chang-hui XIONG Yu-hua QIN Guang-rong 《中国航空学报》2007,20(2):172-176
The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃). 相似文献
20.
YANG Fen ZHANG Xue-jun TIAN Fang WU Xu GAN Fu-xing 《中国航空学报》2007,20(2):181-186
Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration. 相似文献