| 三种钻头钻削CFRP轴向力的时变曲线及预测 |
| |
| 引用本文： | 邱新义,李鹏南,陈安华,牛秋林,黄文亮. 三种钻头钻削CFRP轴向力的时变曲线及预测[J]. 宇航材料工艺, 2018, 48(6): 63-67 |
| |
| 作者姓名： | 邱新义 李鹏南 陈安华 牛秋林 黄文亮 |
| |
| 作者单位： | 湖南科技大学机电工程学院, 湘潭 411201,湖南科技大学机电工程学院, 湘潭 411201,湖南科技大学机械设备健康维护省重点实验室, 湘潭 411201,湖南科技大学机电工程学院, 湘潭 411201,湖南科技大学机电工程学院, 湘潭 411201 |
| |
| 基金项目： | 国家自然科学基金（No.51775184，No.51275168，No.51605161）；湖南省自然科学基金（No.2015JJ5028） |
| |
| 摘 要： | 采用二刃、三刃双锋角钻头和圆弧形钻头钻削CFRP单向板,研究钻削过程中轴向力时变曲线的特征,并探索用预测轴向力时变曲线上的关键拐点的方法来构建预测轴向力时变曲线模型。结果表明:三刃双锋角钻头的轴向力时变曲线最为稳定,钻削过程最为稳定;轴向力最大的是三刃双锋角钻头,其次是圆弧形钻头,最小的是二刃双锋角钻头,说明二刃双锋角钻头适合钻削CFRP;用预测轴向力时变曲线上的关键拐点的方法构建的轴向力时变曲线可以很好地预测双锋角钻头轴向力时变曲线。
|
| 关 键 词： | CFRP 轴向力 双锋角钻头 圆弧形钻头 |
| 收稿时间： | 2018-06-27 |
Thrust Force Versus Time Curves and Their Prediction in Drilling CFRP With Three Kinds of Drills |
| |
| QIU Xinyi,LI Pengnan,CHEN Anhu,NIU Qiulin and HUANG Wenliang. Thrust Force Versus Time Curves and Their Prediction in Drilling CFRP With Three Kinds of Drills[J]. Aerospace Materials & Technology, 2018, 48(6): 63-67 |
| |
| Authors: | QIU Xinyi LI Pengnan CHEN Anhu NIU Qiulin HUANG Wenliang |
| |
| Affiliation: | College of Mechanical and Electrical Engineering, Hunan University of Science and Technology, Xiangtan 411201,College of Mechanical and Electrical Engineering, Hunan University of Science and Technology, Xiangtan 411201,Hunan Provincial Key Laboratory of Health Maintenance for Mechanical Equipment, Hunan University of Science and Technology, Xiangtan 411201,College of Mechanical and Electrical Engineering, Hunan University of Science and Technology, Xiangtan 411201 and College of Mechanical and Electrical Engineering, Hunan University of Science and Technology, Xiangtan 411201 |
| |
| Abstract: | In this paper, the two-edged double point angle drill, three-edged double point angle drill and arcshaped drill were used to drill CFRP.The characteristics of drilling thrust force versus time curve are studied.And the model of predicting the time varying curve of thrust force is constructed by using the method of predicting the critical inflection point of the time varying curve.The results show that the thrust force curve of the three-edged double point angle drill is the most stable, it means that the drilling process is the most stable.The maximum thrust force is the three-edged double point angle drill, followed by the arc-shaped drill, and the minimum is the two-edged double point angle drill.So, the two-edged double point angle drill is suitable for drilling CFRP.The thrust force versus time curve constructed by the method of predicting the critical inflection point on the time varying curve of thrust force can predict the thrust force versus time curve of double point angle drill. |
| |
| Keywords: | CFRP Thrust force Double point angle drill Arc shaped drill |
| 本文献已被 CNKI 等数据库收录！ |
| 点击此处可从《宇航材料工艺》浏览原始摘要信息 |
|
点击此处可从《宇航材料工艺》下载全文 |
|
