首页 | 本学科首页   官方微博 | 高级检索  
     

3D打印赋形微小流道集热器内层流换热特性数值模拟与试验研究
引用本文:黄圳, 李志慧, 孙敬文, 等. 3D打印赋形微小流道集热器内层流换热特性数值模拟与试验研究[J]. 航天器环境工程, 2022, 39(1): 47-54 DOI: 10.12126/see.2022.01.007
作者姓名:黄圳  李志慧  孙敬文  牛科研  汪东莉  赵长颖
作者单位:上海交通大学 机械与动力工程学院;上海卫星装备研究所 上海 200240;上海卫星装备研究所 上海 200240;上海交通大学 机械与动力工程学院
基金项目:中国博士后科学基金项目(编号:2021M702087)
摘    要:针对星内载荷存在大功率、多热源、高度非均匀功率密度的传散热需求,研发了一种3D打印赋形微小流道集热器。在评估了用数值模拟方法预测复杂构型微小流道集热器流动换热特性之可行性基础上,采用数值模拟与试验相结合的方法,研究流量、入口温度、热功率及重力对集热器内层流换热特性的影响,获得了集热器阻力系数与努塞尔数的经验关联式,并优化了微小流道集热器构型。结果表明:随着流量的增大,集热器压降近似线性增大,而总传热系数的提升速率逐渐减小;提升入口温度或热功率会引起集热器压降降低与总传热系数增大;重力对微小流道集热器压降及总传热系数的影响较小。

关 键 词:大功率热源   赋形微小流道集热器   层流   换热特性   数值模拟
收稿时间:2021-09-08

Numerical simulation and experimental study of laminar flow and heat transfer in the 3D-printed shape follow-up minichannel thermal collector
HUANG Z, LI Z H, SUN J W, et al. Numerical simulation and experimental study of laminar flow and heat transfer in the 3D-printed shape follow-up minichannel thermal collector[J]. Spacecraft Environment Engineering, 2022, 39(1): 47-54 DOI: 10.12126/see.2022.01.007
Authors:HUANG Zhen  LI Zhihui  SUN Jingwen  NIU Keyan  WANG Dongli  ZHAO Changying
Affiliation:1.School of Mechanical Engineering, Shanghai Jiaotong University2.Institute of Shanghai Spacecraft Equipment: Shanghai 200240, China
Abstract:Based on the heat transfer and dissipation in cases of high power, multi heat sources and highly non-uniform power density for some special satellite payload, a 3D-printed shape follow-up minichannel thermal collector is developed. In view of the assessed reliability of the numerical simulation method to predict the flow and heat transfer performances of the complex 3D-printed minichannel thermal collector, the effects of the flow rate, the inlet temperature, the thermal power and the gravity on the laminar heat transfer characteristics of the thermal collector are studied by the numerical simulation and the experiment, respectively. The empirical relations between the friction factor and the Nusselt number for the thermal collector are obtained, and the structure of the minichannel thermal collector is thus optimized. It is shown that with the increase of the flow rate, the pressure drop of the thermal collector increases approximately linearly, and the increase rate of the total heat transfer coefficient decreases gradually. Increasing the inlet temperature or the thermal power would reduce the pressure drop and increase the total heat transfer coefficient of the thermal collector. Gravity has little effect on the pressure drop and the total heat transfer coefficient of the minichannel thermal collector.
Keywords:
本文献已被 万方数据 等数据库收录!
点击此处可从《航天器环境工程》浏览原始摘要信息
点击此处可从《航天器环境工程》下载全文
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号