A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

Unsteady wakes-secondary flow interactions in a high-lift low-pressure turbine cascade

Detailed experimental measurements were conducted to study the interactions between incoming wakes and endwall secondary flow in a high-lift Low-Pressure Turbine (LPT) cascade. All of the measurements were conducted in both the presence and absence of incoming wakes, and numerical analysis was performed to elucidate the flow mechanism. With increasing Reynolds number, the influence of the incoming wakes on suppressing the secondary flow gradually increased owing to the greater influence of incoming wakes on reducing the negative incidence angle at higher Reynolds numbers, leading to a lower blade loading near the leading edge and suppression of the Pressure Side (PS) leg of the horseshoe vortex. However, the effect of unsteady wakes on suppressing the profile losses gradually became weaker owing to the reduced size of the Suction Side (SS) separation bubble and increased mixing loss in the free-flow region at high Reynolds numbers. Incoming wakes clearly improved the aerodynamic performance of the low-pressure turbine cascade at low Reynolds numbers of 25,000 and 50,000. In contrast, at the high Reynolds number of 100,000, the profile loss at the midspan and mass-averaged total losses downstream of the cascade were higher in the presence of wakes than in the absence of wakes, and the unsteady wakes exerted a negative influence on the aerodynamic performance of the LPT cascade.     

流动阻力及能量损失对注射成型制件的影响

本文分析了在塑料熔体充满型腔的过程中，流动阻力及能量损失产生的形式和物理原因，进而讨论了对塑料制件成型及凝固过程中的影响。并提出降低影响的措施。     

预测悬停旋翼跨音速流动的一种组合自由尾流/CFD方法

一种新的组合自由尾流 / CFD方法用于悬停旋翼流动的 CFD解中以考虑实际尾流的作用 .用文中描述的尾流分析方法研究了螺旋尖涡的运动 .首先从广义尾流模型开始 ,用半经验公式模化了涡核对旋翼尾流的作用 ;然后在环量收敛和尾迹收敛的条件下完成了自由尾迹计算 ;最后应用 Jameson有限体积龙格 -库塔推进格式求解了欧拉方程 .所得结果与相关文献和实验数据进行了比较     

ADI方法求解完全跨声速非定常小扰动方程

本文修改了Whitlow的ADI格式,以便求解另一变形的完全跨声速小扰动方程。本文给出的NACA64A006和NACA0012翼型的非定常跨声速流动的计算结果与其它数值结果和实验结果的比较表明本文格式是合理的且便于实际应用的。     

域外刑事评议程序之比较研究

刑事评议程序是介于庭审程序和宣告程序之间的一个重要程序,它既是庭审的自然延续,又是裁判结论形成的前提和基础。然而,欲保证刑事评议程序的正常运行,刑事评议主体之独立必须得到保证;刑事评议之客体还应被全面考虑,并对其进行细化,以确保刑事评议的针对性和有效性,防止出现"估堆"现象。本文以域外刑事评议程序为对象,从评议的主体、客体等角度进行梳理,得出规律性的认识,以期对我国关于刑事评议的立法有所裨益。     

炉渣滤床技术处理亚麻生产废水

为了确定处理包头亚麻厂亚麻生产废水的设计方案，设计之前在现场进行了生产试验。在包头亚麻厂污水处理站，模拟炉渣滤床制造了3米高的炉渣滤层，滤渣从工厂锅炉房取用，将实际排放的亚麻煮漂车间、细纱车间、粗纱车间的生产废水混合后，通过炉渣滤层过滤处理，处理后出水由厂化验室和包头环保局化验。试验结果表明，处理后的排水各项指标完全达到国家排放标准。该工艺处理费用低，运行效果稳定，管理简便，具有明显的经济效益、环境效益和社会效益。     

400kN振动台承力钢架的研制

文章中介绍的400kN 承力钢架是用来作船罩联合试验的承力机构,具有结构庞大、复杂的特点,对自振频率有一定要求,文章介绍了该设备研制过程中的设计、计算、加工及安装工艺技术等。     

掠海飞行导弹击水概率的仿真研究

本文对掠海导弹的击水概率问题进行了研究,提出了用均匀设计、Monte—Carlo法和逐步回归法建立击水概率预报公式的仿真方法,并结合某型号的反舰导弹进行计算,得到了满意的结果。本文还利用表观频率和表观频谱的概念,建立起飞航导弹的背景干扰——海浪和阵风的数学模型,并用波叠加法进行了数字仿真。     

区域开发战略目标定量研究--兼论区域开发战略目标矛盾的协调

文章在回顾我国区域开发战略的基础上,结合我国区域经济发展现状,利用层次分析法建立了区域开发战略模型.通过定量研究,得出了我国区域经济发展必须以社会公平为主目标,同时兼顾效率和可持续发展目标.