Fault mode probability factor based fault-tolerant control for dissimilar redundant actuation system

This paper presents a Fault Mode Probability Factor (FMPF) based Fault-Tolerant Control (FTC) strategy for multiple faults of Dissimilar Redundant Actuation System (DRAS) composed of Hydraulic Actuator (HA) and Electro-Hydrostatic Actuator (EHA). The long-term service and severe working conditions can result in multiple gradual faults which can ultimately degrade the system performance, resulting in the system model drift into the fault state characterized with parameter uncertainty. The paper proposes to address this problem by using the historical statistics of the multiple gradual faults and the proposed FMPF to amend the system model with parameter uncertainty. To balance the system model precision and computation time, a Moving Window (MW) method is used to determine the applied historical statistics. The FMPF based FTC strategy is developed for the amended system model where the system estimation and Linear Quadratic Regulator (LQR) are updated at the end of system sampling period. The simulations of DRAS system subjected to multiple faults have been performed and the results indicate the effectiveness of the proposed approach.     

Topology optimization in lightweight design of a 3D-printed flapping-wing micro aerial vehicle

Topology optimization is an effective method to obtain a lightweight structure that meets the requirements of structural strength. Whether the optimization results meet the actual needs mainly depends on the accuracy of the material properties and the boundary conditions, especially for a tiny Flapping-wing Micro Aerial Vehicle (FMAV) transmission system manufactured by 3D printing. In this paper, experimental and numerical computation efforts were undertaken to gain a reliable topology optimization method for the bottom of the transmission system. First, the constitutive behavior of the ultraviolet (UV) curable resin used in fabrication was evaluated. Second, a numerical computation model describing further verified via experiments. Topology optimization modeling considering nonlinear factors, e.g. contact, friction and collision, was presented, and the optimization results were verified by both dynamic simulation and experiments. Finally, detailed discussions on different load cases and constraints were presented to clarify their effect on the optimization. Our methods and results presented in this paper may shed light on the lightweight design of a FMAV.     

纵向短周期模态试飞方法和选择

对几种纵向短周期模态试飞方法及其适用性进行了初步分析。结合实际飞行经验,提出了初步判断飞机短周期特性及选择试飞方法。     

基于模糊粗糙集的飞机远程故障诊断模型研究

粗糙集和模糊集结合在飞机故障诊断领域有巨大的发展潜力。针对当前飞机故障诊断中所存在的问题,借助C/S模式,将粗糙集和模糊集结合,提出一种新型的飞机远程故障诊断模型,并且开发出远程诊断系统框架。系统的可行性和有效性得到了飞机故障诊断实例的证实。该系统具有客户端响应快、系统效率高、诊断及时的特点,对于当前民用飞机远程故障诊断具有重要应用价值。     

动态差压检测系统的共模误差研究

主要针对以差压变送器为核心的动态差压检测系统的特点 ,应用流体网络分析方法 ,提出了动态差压检测系统中的共模误差问题。理论分析和仿真计算结果表明 :共模误差与检测系统两侧引压管路的不一致性直接相关 ,为了获得动态差压信号的准确检测 ,必须对动态差压检测系统的共模误差予以抑制     

正—反激组合式变换器与单端式变换器的比较

以５０Ｗ变换器为例，分别从磁性元件的大小，功率管上的电应力、磁恢复问题，输出纹波及输出特性等方面，详细分析比较了组合式变换器与单端式变换器的优缺点，并给出了具体数据，提出了正－反激组合式变换器具有电压应力低，磁性元件小，体积小，重量轻，输出纹波小及可靠性高的结论。     

导弹电液伺服机构的模糊滑模变结构跟踪控制研究

为减小导弹电液伺服机构滑模变结构跟踪控制中的抖振,研究了一种模糊滑模变结构控制(FS-MVSC)方法。给出了模糊滑模控制器的构成,以及模糊化、模糊规则与推理、反模糊化处理的方法。在保持系统对参数变化和外干扰不确定强鲁棒性的同时,可使系统具有较优的动态响应和稳态控制精度。仿真结果表明,该控制方案有效。     

新型总线式电子设备结构设计

讨论了用现代设计方法学理论确定总线式电子设备结构设计方案的方法 ,将现代设计方法学理论应用于结构设计 ,可以使设备结构设计更加合理 ,使电子设备更能适应新技术的发展和设计周期短 ,生产批量大的要求。     

ILD智能交通流量测试仪

介绍一种交通流量测试仪，它具有高灵敏度、高信噪比、传输距离远，可以准确地测量机动车、自行车流量，且成本低。由于该仪器设置了驱动变送器，采用了一种新的传输结构，引入了微机技术，模式识别等技术，从而研制出性能稳定、操作方便、实用性强且具有国际先进水平的道路交通流量测试装置。