排序方式: 共有10条查询结果,搜索用时 15 毫秒
1
1.
2.
目前细长小孔的超精密光整加工已成为保证液压系统清洁度要求、避免伺服阀喷嘴或油滤孔堵塞的一项关键技术。通过分析液压系统中细长小孔的结构特征与功能特点,分别从底孔加工、孔壁光整和清洗等方面进行细长小孔超精密光整加工技术研究,成功实现细长小孔孔壁均匀光整与高清洁度指标要求。 相似文献
3.
文章简要介绍了碳/环氧复合材料薄壁细长管件的研制情况,着重介绍了工艺方案选定、选材和材料特性试验、成型工艺及解决主要技术难点等内容。制品经地面环模和飞行试验考验,取得了满意效果。 相似文献
4.
5.
振动严重影响细长轴的加工质量,由于细长轴类长径比大、刚性差,故很难控制其切削过程产生的振动.本文从振动的角度对细长轴切削时变形情况进行了分析,建立其振动的数学模型,并提出运用水射流辅助支撑来控制细长轴在切削过程中的振动.最后,对细长轴在有无水射流辅助支撑作用下进行了试验对比分析.结果表明,水射流辅助支撑可很好地控制细长轴加工振动,为提高细长轴的精度提供理论指导. 相似文献
6.
Experiments and computations were performed over an ogive-cylinder body having an lift-to-drag ratio of 16 at a diameter Reynolds number of 29000. The side force on the slender body augments with increasing angles of attack for the case without a ring. This increase was mainly due to the increase in the asymmetry of the existing vortex pair in the wake of the body. Attempts were made to completely reduce the existing side force at the angle of attack ranging from 35° to 45°.Three rectangular cross-sectioned circumferential rings having a height of 3% of the local diameter were placed at axial distances of 2.5, 3.5 and 4.5 times the base diameter from the tip of the body so as to reduce the side force. The results obtained indicate that inclusion of three rings completely alleviated the side force on the slender body at the angle of attack ranging from 0° to 45°. The presence of rings was found to alter the growth of the vortices that helped in the reduction of the side force. Computations performed were in reasonable agreement with the experiments. 相似文献
7.
8.
9.
10°尖锥气动特性边界层转捩诱导量的测定研究 总被引:1,自引:0,他引:1
本文用风洞实验的方法在国内外首次测出了10°尖锥气动特性的转捩诱导量,包括转捩诱导法向力及其作用点,转捩诱导俯仰力矩和尖锥压心的转捩诱导量。研究结果表明,这些转捩诱导量随Re数的变化趋势合理,具有确定的规律性。研究认为,这些转捩诱导量产生的原因是细长锥边界层转捩的不对称性。利用这些结果,可以很好地解释边界层转捩何以对细长锥的气动静稳定性和气动稳定性产生极为显著的影响以及静、动稳定性转捩诱导量之间的相关现象。此外,这个研究结果还有助于证明边界层转捩将影响物面的压力分布。本研究是在M=5,α=0°的流场中完成的,实验的Re数范围为ReL=2.8×106~13.8×106。 相似文献
10.
王秋林 《华北航天工业学院学报》2001,(1)
本文针对长径比大于80:1的细长轴精密加工问题,从车刀角度、车削方法、车床尾座、跟刀架等方面提出了改进措施,从而满足了加工要求,提高了生产效率。 相似文献
1