Fully distributed time-varying formation tracking control for multiple quadrotor vehicles via finite-time convergent extended state observer

This paper investigates a time-varying anti-disturbance formation problem for a group of quadrotor aircrafts with time-varying uncertainties and a directed interaction topology. A novel Finite-Time Convergent Extended State Observer (FTCESO) based fully-distributed formation control scheme is proposed to enhance the disturbance rejection and the formation tracking performances for networked quadrotors. By adopting the hierarchical control strategy, the multi-quadrotor system is separated into two subsystems: the outer-loop cooperative subsystem and the inner-loop attitude subsystem. In the outer-loop subsystem, with the estimation of disturbing forces and uncertain dynamics from FTCESOs, an adaptive consensus theory based cooperative controller is exploited to ensure the multiple quadrotors form and maintain a time-varying pattern relying only on the positions of the neighboring aircrafts. In the inner-loop subsystem, the desired attitude generated by the cooperative control law is stably tracked under a FTCESO-based attitude controller in a finite time. Based on a detailed algorithm to specify the cooperative control protocol, the feasibility condition to achieve the time-varying anti-disturbance formation tracking is derived and the rigorous analysis of the whole closed-loop multi-quadrotor system is given. Some numerical examples are conducted to intuitively demonstrate the effectiveness and the improvements of the proposed control framework.     

基于鲁棒故障检测滤波器的传感器故障诊断

本文讨论了鲁棒故障检测滤波器在喷气式发动机传感器故障诊断中的应用。鲁棒故障检测滤波器方法使残差既有干扰解耦特性又有方向特性。该滤波器的设计结合了未知输入观测器原理与Beard故障检测滤波器原理。利用未知输入观测器产生的残差对未知输入(干扰)具有鲁棒性,而特定方向性是基于BFDF技术获得的。最后举例说明了该方法的可行性和有效性。     

基于四元数估计角速率的陀螺故障定位

当卫星速率积分陀螺的配置冗余度不满足一致性检验条件时，不能单纯利用硬件冗余实现陀螺的故障定位。鉴于角度和角速度敏感器的输出通过卫星运动学相关，本文利用姿态测量敏感器的输出来诊断陀螺故障。首先根据姿态测量敏感器的输出得到卫星姿态四元数，进而根据四元数动力学方程得到粗略的姿态角速度信息，并将此角速度作为输出信息用于对卫星动力学方程的滤波，从而得到较精确的角速度信息，为单冗余度陀螺组件的故障定位提供解析冗余信息。利用四元数方法可以避免出现奇点。仿真结果证明了该方法的有效性。     

浮栅ROM器件的质子辐射效应实验研究

给出了浮栅ROM器件的质子辐射效应实验结果.认为浮栅ROM28C256和29C256的质子辐射效应不是单粒子效应,而是质子及其次级带电粒子产生的累积剂量造成的总剂量效应.器件出现错误有个质子注量阈值.对于29C256,高温加电退火容易消除质子产生的辐射损伤;对于28C256,高温加电退火不易消除质子产生的辐射损伤.动态监测和静态加电的器件都出现数据错误,且不能用编程器重新写入数据.然而不加电的器件在更高的质子注量辐照下未出现错误.对于应用浮栅ROM器件的航天器电子系统,冷备份是提高其可靠性的有效手段之一.     

基于干扰观测器的新一代歼击机鲁棒飞行逆控制器设计

基于干扰观测器设计了新一代歼击机的鲁棒飞行逆控制器。根据时标分离的原则，将机动飞机分为快慢不同的回路。采用动态逆方法设计了快回路和慢回路控制器，并在慢回路用干扰观测器估计飞机所受的扰动，同时，用于在线补偿动态逆误差。仿真结果表明，该设计合理。     

火箭型单级入轨（SSTO）的初步分析

火箭型单级入轨（ＳＳＴＯ）是今后的发展方向之一，从多方面分析了火箭型单级入轨（ＳＳＴＯ）方案的可能性，简要回顾了ＳＳＴＯ的发展历史，特别对三角快帆（ＤＣ－Ｃｌｉｐｐｅｒ）作了分析，认为采取多项先进技术后是完全可以实现的。明确了单级入轨的两个基本方向：提高比冲和降低结构重量。分析了采用不同形式发动机的影响，列出了主要关键技术，最后提出了几个有参考价值的观点。     

点焊质量模糊控制系统研究

简要介绍了电阻点焊单片机微机模糊控制原理，确定了点焊模糊控制算法，分析了点焊模糊控制系统的硬件结构和软件设计。实验结果表明，该控制系统能够有效实现点焊质量的模糊控制，具有较强的自适应特性，可用于电阻焊智能制造。     

基于干扰观测器的天基观测航天器姿态控制设计

与地基空间目标监视系统相比,天基观测系统具有监视范围广,不受国界限制,观测精度高等优点,是未来空间目标观测技术的重要发展方向。但天基观测航天器工作时,相机转台的运动,太阳能帆板挠性部件的弹性振动与航天器的姿态运动相互影响,构成强耦合的非线性系统,传统的控制方案无法实现对这类天基观测航天器的高精度姿态控制。文章针对某一空间观测航天器的任务要求,设计了基于干扰观测器的前馈补偿航天器姿态控制系统,仿真实验结果表明:姿态角控制精度小于 0.06°,姿态角速度精度小于 0.03(°)/s,达到了精度要求。     

Simultaneous state and actuator fault estimation for satellite attitude control systems

In this paper, a new nonlinear augmented observer is proposed and applied to satellite attitude control systems. The observer can estimate system state and actuator fault simultaneously. It can enhance the performances of rapidly-varying faults estimation. Only original system matrices are adopted in the parameter design. The considered faults can be unbounded, and the proposed augmented observer can estimate a large class of faults. Systems without disturbances and the fault whose finite times derivatives are zero piecewise are initially considered, followed by a discussion of a general situation where the system is subject to disturbances and the finite times derivatives of the faults are not null but bounded. For the considered nonlinear system, convergence conditions of the observer are provided and the stability analysis is performed using Lyapunov direct method. Then a feasible algorithm is explored to compute the observer parameters using linear matrix inequalities (LMIs). Finally, the effectiveness of the proposed approach is illustrated by considering an example of a closed-loop satellite attitude control system. The simulation results show satisfactory perfor-mance in estimating states and actuator faults. It also shows that multiple faults can be estimated successfully.     

Machining of a film-cooling hole in a single-crystal superalloy by high-speed electrochemical discharge drilling

Single-crystal superalloys are typical advanced materials used for manufacturing aeroengine turbine blades. Their unique characteristics of high hardness and strength make them exceedingly difficult to machine. However, a key structure of a turbine blade, the film-cooling hole,needs to be machined in a single-crystal superalloy; such machining is challenging, especially considering the increasing levels of machining efficiency and quality demanded by the aeroengine industry. Tube electrode high-speed electrochemical discharge drilling(TSECDD), a hybrid technique of high-speed electrical discharge drilling and electrochemical machining, provides high machining efficiency and accuracy, as well as eliminating the recast layer. In this study, TSECDD is used to machine a film-cooling hole in a nickel-based single-crystal superalloy(DD6). The Taguchi methods of experiment are used to optimise the machining parameters. Experimental results show that TSECDD can effectively drill the film-cooling hole; the optimum parameters that give the best performance are as follows: pulse duration: 12 ls, pulse interval: 30 ls, peak current:6 A, and salt solution conductivity: 3 m S/cm. Finally, a hole is machined by TSECDD, and the results are compared with those obtained by electrical discharge machining. TSECDD is found to be promising for improving the surface quality and eliminating the recast layer.