Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

某型制导雷达部分元器件失效模式的分析

对某型号制导雷达部分元器件进行了失效分析，找出了导致元器件失效的原因，指出设计是提高可靠性的关键，并根据有关元器件情况对生产方与使用方提出了建议。着重讨论了设计师应注意的问题和应该遵循的设计原则。针对失效情况，提出了一些具体的设计构想。     

历经十年寿命试验的消旋天线机构轴承的可靠性分析

解决了一个计算可靠性问题的特例。分析了消旋天线机构轴承历经10年寿命试验的可靠性问题。并给出了轴承在不同可靠寿命要求下的可靠度(对应不同置信度)。     

三轴稳定遥感卫星姿控系统故障情况下的系统重构

论述三轴对地稳定遥感卫星姿控系统中部分轮子或部分陀螺故障情况下的姿控系统重构。文中论述了只在俯仰通道有一偏置动量轮正常工作，而滚动和偏航通道轮子故障条件下的系统重构。另外还论述了偏航陀螺故障，姿控系统其它部件正常情况下，控制系统采用Whecon原理与PIM控制相结合的设计。以上两种系统重构拟用于实际系统中，经过数学仿真验证，姿控系统在故障情况下能够完成基本任务。     

Digital Aircraft Sheet Metal Part Manufacturing System and Its Key Technology

The architecture of digital sheet metal manufacturing system is proposed based on the classification of sheet metal manufacturing information.The essence of digital manufacturing is the definition,management and transfer of information,and the key technologies are brought forward and described.It is pointed out that knowledge-based manufacturing elements design is necessary to make digital technology efficient.The management of all kinds of sheet metal manufacturing element information is to build single source of manufacturing data.Multi-state model-based digital transfer and coordination method is designed to provide a foundation for digital manufacturing of aircraft sheet metal part.The application of digital sheet metal manufacturing is exemplified with an aircraft sheet metal part.The application result is compared to that of the traditional analog transfer technology.It is shown that the developed technology can improve part quality,shorten manufacturing time and lower manufacturing cost.     

中心极限定理用于近似计算时必须注意的问题

本文着重指出,在运用中心极限定理近似计算独立同泊松分布随机变量之和的概率时,通常只注意了取n适当大的值,从而导致了差异较大的不同结果。本文指出了不仅要使n适当的大,而且也要使nλ足够地大。当X_h是其他离散型随机变量时,也要考虑类似的问题。     

变轨发动机不等量截尾试验可靠度评估

对于可靠度要求极高和任务时间以小时计的变轨发动机来说，目前广泛采用以铌合金为材料并喷涂以抗高温氧化涂层方案的推力室，这一类发动机在方案试验阶段结束后的研制试验中往往只出现截尾试验的结果。给出了不等量截尾试验结果的可靠度评估方案。     

故障检测与分离的广义一致性算子法

本文提出了故障检测与分离的广义一致性算子法的一般形式。得出了两个故障可分离的充要条件和多个故障可分离的充要条件。最后给出了检测和分离故障的过程。     

载人航天可靠性与空间环境试验

文章通过对国外载人航天事故统计,分析各种空间环境条件对航天器及航天员的影响,阐述了空间环境试验对提高载人航天可靠性的重要意义,提出为了提高载人航天的可靠性,应进行充分和严格的空间环境模拟试验。     

一种小样本和小失效数系统可靠性分析方法

根据小样本和小失效数系统的特点，以及可靠性分布函数和参数估计的不确定性和模糊性，提出了一种可靠性分析方法。采用指数分布族，通过分析最少和最大失效数两种最极端状态，确定中间状态的备选点，运用最小平方差原理进行逐个筛选，并给出了算法流程。分析结果表明，计算值与实际观测值较为吻合。该方法可使系统可靠性的估计精度有较大提高。