普通高校一年级体育课程教学模式的构建

在总结以往多年教学经验的基础上，对目前体育课程发展状况进行了研究和理性思考，淮阴工学院在一年级进行体育课程改革与实践，提出“主项课”的教学模式，取得一定的成效。同时，对存在的一些主要问题提出进一步的设想和改进措施。     

波导分支线定向耦合器计算方法

利用模匹配方法和网络理论分析计算了一种卫星天线系统中常用的波导分支线定向耦合器,计算结果与实验结果非常吻合。该方法为波导分支线定向耦合器提供一种有力的设计手段。它可直接用于设计Ku 波段通信卫星天线的波束形成网络,也可以用来设计各种耦合度的波导分支线定向耦合器。     

空间交会动力学和安全模式

本文首先导出空间交会相对运动方程并给出其物理解释,然后给出动力学方程的解析解,并分析其动力学性质,最后导出不碰撞安全区和位置保持点的表达式。选择适当初始条件可以求出安全区和保持点。     

随振动量级增加卫星结构频率下移的分析

对卫星振动频率随量级增加而出现下降，即振动频率“漂移”的现象进行了初步分析。发现随振动量级的增加。结构的非线性表现突出。结构的刚度下降和阻尼增加，可认为主要是由蜂窝材料的非线性因素所致。     

航空发动机全程滑态变结构控制研究

一种新的滑模变结构控制方法-全程滑态变结构控制首次应用于航空发动机控制系统，该控制方法能有效地缩短系统状态到达滑动模态的时间，避免了定常滑态变结构控制系统在能达阶段对扰动的敏感性，且其控制律的设计可以改善系统的瞬态性能，克服未知参数摄动的影响，仿真结果表明，基于全程滑态变结构控制所设计的发动机控制系统，其鲁棒性要优于发动机定常滑态结构控制系统。     

特征结构配置在飞机模态解耦中的应用

主要对特征结构配置在飞机模态解耦中的应用问题进行研究,并以某飞机横航向小扰动运动为例,按照飞机飞行品质规范要求,给出荷兰滚模态和滚转模态解耦控制的设计方法。     

Initial nighttime ionospheric observations with advanced ionospheric probe onboard FORMOSAT-5

FORMOSAT-5 satellite was launched into a sun-synchronous orbit at 720 km altitude with 98.28° inclination on 25 August 2017. The onboard scientific payload, Advanced Ionospheric Probe (AIP) is capable of measuring topside ionospheric ion density, cross-track flow velocities, ion composition and temperature, and electron temperature. Initial observations of nighttime midlatitude ionospheric density and vertical flow velocity variations at 2230 LT sector during a few quiet magnetic days in December 2017 are studied here. Longitudinal density variations in the equatorward edge of midlatitude ionospheric trough (MIT) region are noticed. Accompanied with this density variation, the vertical flow velocities also behave differently. Although the density difference has been stated due to zonal wind effect related to the declination of the geomagnetic field lines, the vertical flow velocity variation seems to play the opposite role. All these density and vertical flow observations in the northern winter hemisphere can only be explained by the longitudinal differences in the diffusion velocity coming down from the protonsphere (plasmasphere). In addition, the hemispheric asymmetry in the vertical flow velocity can also be explained by the interaction between the topside ionosphere and the protonsphere. The observed vertical flow variations near MIT at different longitudes should present a new potential tool for the study of MIT formation.     

High temporal resolution global PWV dataset of 2005–2016 by using a neural network approach to determine the mean temperature of the atmosphere

Atmospheric water vapour plays an important role in phenomena related to the global hydrologic cycle and climate change. However, the rapid temporal–spatial variation in global tropospheric water vapour has not been well investigated due to a lack of long-term, high-temporal-resolution precipitable water vapour (PWV). Accordingly, this study generates an hourly PWV dataset for 272 ground-based International Global Navigation Satellite System (GNSS) Service (IGS) stations over the period of 2005–2016 using the zenith troposphere delay (ZTD) derived from global-scale GNSS observation. The root mean square (RMS) of the hourly ZTD obtained from the IGS tropospheric product is approximately 4 mm. A fifth-generation reanalysis dataset of the European Centre for Medium-range Weather Forecasting (ECMWF ERA5) is used to obtain hourly surface temperature (T) and pressure (P), which are first validated with GNSS synoptic station data and radiosonde data, respectively. Then, T and P are used to calculate the water vapour-weighted atmospheric mean temperature (Tm) and zenith hydrostatic delay (ZHD), respectively. T and P at the GNSS stations are obtained via an interpolation in the horizontal and vertical directions using the grid-based ERA5 reanalysis dataset. Here, Tm is calculated using a neural network model, whereas ZHD is obtained using an empirical Saastamoinen model. The RMS values of T and P at the collocated 693 radiosonde stations are 1.6 K and 3.1 hPa, respectively. Therefore, the theoretical error of PWV caused by the errors in ZTD, T and P is on the order of approximately 2.1 mm. A practical comparison experiment is performed using 97 collocated radiosonde stations and 23 GNSS stations equipped with meteorological sensors. The RMS and bias of the hourly PWV dataset are 2.87/?0.16 and 2.45/0.55 mm, respectively, when compared with radiosonde and GNSS stations equipped with meteorological sensors. Additionally, preliminary analysis of the hourly PWV dataset during the EI Niño event of 2014–2016 further indicates the capability of monitoring the daily changes in atmospheric water vapour. This finding is interesting and significant for further climate research.     

工业CT检测技术在5 kN发动机研制中的应用

针对5 kN发动机结构焊缝和复合材料喷管不可检不可测的难题,开展了工业CT检测技术研究。分析了复杂结构焊缝和复合材料喷管的常规方法检测难点,利用工业CT检测技术穿透能力强、不受工件复杂结构影响的优势,对5 kN发动机产品中的电子束焊缝、氩弧焊焊缝、复合材料喷管等结构进行了检测试验,得到了良好的检测效果。结果表明,工业CT检测技术可以识别5 kN发动机产品中的气孔、未焊透、分层、裂纹等缺陷,并实现对缺陷的定位与测量,可为焊缝质量评估提供依据。     

MA 及原位-热压合成TiC/ Ti5 Si3 复合材料

以Ti粉、Si粉和C粉为原料,利用高能球磨及热压工艺合成了TiC/Ti5Si3陶瓷复合材料。研究了工艺条件尤其是热压温度对合成产物相组成及微观结构的影响,并结合DSC、XRD和SEM对反应合成机理进行探讨。结果表明:通过优化合成工艺,高能球磨12 h,热压温度1 400℃时,烧结6 h得到了高纯度的TiC/Ti5Si3陶瓷复合材料;合成过程为:反应开始时发生Ti+C■TiC,反应ΔG=-167.72 kJ/mol。2 h时发生5TiC+8Si■Ti5Si3+5SiC,反应ΔG=-62.12 kJ/mol,当6 h时发生3SiC+8Ti■Ti5Si3+3TiC,反应ΔG=-697.8 kJ/mol。显微结构表明:TiC/Ti5Si3复合材料的合成过程伴随Si熔融,该材料以TiC-Si-Ti5Si3形式相结合,其中Si为黏结剂。