Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

FET振荡器注入锁相伏特拉级数分析

应用伏特拉级数法分析了电容耦合ＦＥＴ振荡系统在外加信号下的注入锁定现象，推导出输出信号和注入锁定带宽表达式。与一般非线性系统分析方法相比，伏特拉级数法在建立好系统模型后只需进行代数运算，从而避开了求解非线性，非齐次高阶微分方程的复杂过程。     

为中国开发太空探路 创中国首飞太空记录——纪念T-7系列探空火箭首次发射成功45周年

在中国第一个实用探空火箭系列——T-7系列探空火箭首次发射成功45周年之际，回顾了该系列火箭的研制由来和基本情况，论述了该系列火箭对中国开发中层大气和太空所起到的探路作用。     

等厚度楔形杆的应力分析

本文将应力场分为基本应力场和修正应力场两个部分。基本应力场的应力σ_x用勒让德级数展开,级数的前两项系数用截面法确定;其他应力τ_(xy),σ_y由平衡方程和侧表面边界条件确定;再用余能原理确定其余各项系数。由于该级数收敛很快,故可得到封闭解并能给出该解的应用范围,为精确满足自由端的静力边界条件,又引入一个从自由端到固定端迅速衰减的修正应力场,该应力场的应力在自由端等于已知外力与基本应力解之差。其确定方法与基本应力场相同,它也有一个封闭解。将以上两应力场相加卽可得到满足全部边界条件的解。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

300M钢纯洁度磁粉检验磁痕现象的分析

采用交、直流磁粉检验并结合金相试验、电子探针试验及微量元素含量分析的方法，对３００Ｍ钢磁痕现象的本质进行了分析。结果表明，采用磁粉检验方法对航空优质钢进行纯洁度检验是可信的。     

国家财政主要支出项目与各项税收收入的最优化--回归分析在最优化中的应用研究实例

利用回归分析方法得到国家财政部分主要支出项目，部分税收收入与国内生产总值构成的回归方程，由此构成线性规划问题的约束方程组。再用M单纯形法求最优解。     

混合移频静刚度法和直接扰动迭代法

本文对混合移频动柔度法的失代式进行等价变换，从而得到一个“变种”，该变种不包含混合移频系统的动柔度式F^△（λ*），这便消除了F^△（λ*）带来的近似性，另外，对直接扰动法也进行等价变换，引出可以省时地用于许多特征向量导数计算的直接扰动迭代法。最后，为了供读者参数，本文还导出了三种混合移频动柔度法的非迭代式，其中有两种恰好是另外两种动柔度法经混合移频后的非迭代式，这实际上已将另两种动柔度法也扩展到密集根情况了。     

新型无位置传感器开关磁阻电机的研究

提出了一种新型的基于测试线圈技术的无位置传感器方案.这种方案是通过测量导通相测试线圈的电感来获得实时转子位置的.文中对此进行了理论分析和实验验证,并成功地开发完成了一台无位置传感器开关磁阻电机原理样机.