Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

机载托架自动校准系统的设计与实现

为了解决机载托架传统校准方法精度低、耗时、费力等问题,设计了一种高精度、高效率并且操作简单的成品托架自动校准系统。该系统运用调平精度较高的"循环多次"最高点不动调平方法,建立高精度机载托架校准的静力学数学模型,运用VC与Matlab的COM接口编程技术开发机载托架自动校准系统,并建立良好的人机交互界面。试验结果表明,利用该方法对机载托架进行校准,无论是校准精度还是校准效率都较传统方法有很大提高。     

ADI方法求解完全跨声速非定常小扰动方程

本文修改了Whitlow的ADI格式,以便求解另一变形的完全跨声速小扰动方程。本文给出的NACA64A006和NACA0012翼型的非定常跨声速流动的计算结果与其它数值结果和实验结果的比较表明本文格式是合理的且便于实际应用的。     

精仪工作台定量调整的原理及方法

论述了可调结构仪器工作台的结构、调整原理和调整方法，并以三点支撑结构、锥面支撑结构仪器工作台表面与测量轴线垂直度的调整为例，具体地阐述了调整方法和步骤。     

热处理作业系统中安全性评价的AHP方法

本给出了系统安全性评价的AHP方法，叙述了该方法的基本步骤，并以沈阳某集团公司热处理弹簧厂评价的实例说明了该方法的有效性。     

一种卫星间跟瞄方向的控制策略与实现

进行自由空间的光通信或空间对抗，需要在卫星间实现精确的跟踪与瞄准。因为地面测控站的设置非常有限，指令与数据注入的范围受到很多限制，所以要求这种跟瞄在很多时候是无主控制状态下完成的。提出了一种利用在地面测控站的范围内向星上数管中心注入目标卫星、本体卫星的轨道参数，其它时间依靠自主导航飞行和GPS修正的方法，结合本体星的姿态测量、振动测量实现卫星瞄准指向的方位角与俯仰角的精确控制的方法，提高了在地面站无法注入指令与数据时卫星的捕获概率。通过仿真，将计算结果与卫星仿真工具软件STK的数据进行比较，结果一致。最后在嵌入式DSP平台上实现了这一策略。     

在二元柔壁自适应风洞中利用面元法进行三元模型实验

简要叙述了在西北工业大学二元柔壁自适应风洞中利用面元法进行二元半机翼模型试验的研究情况，分析了面元法的基本思想和部分试验结果。     

Ту-154М变稳飞机空中飞行模拟试验评述

依据Ту－１５４М变稳飞机的特点，主要进行了不同操纵器、不同控制律和不同显示画面的飞行试验研究。特别是通过中央杆和侧杆、电传系统不同控制律飞行品质特性之间、两种先进控制方案及不同显示方式的比较，不仅掌握了这方面的试飞技术和评定技术，还亲身体验到变稳飞机在发展仿真技术，新机预研及提高试飞员试飞技术和评定技术等方面的巨大作用。