排序方式: 共有23条查询结果,搜索用时 281 毫秒
1.
复合材料在DCB试验中的裂纹尺寸效应 总被引:2,自引:0,他引:2
在许多关于复合材料Ⅰ型层间断裂韧性试验研究工作中,不同的作者所选取的有效裂纹长度有很大的差异,由此带来试验结果分散程度很大,试验结果无法相互比较等问题。本文对复合材料在Ⅰ型层间断裂DCB试验中裂纹的预裂长度、裂纹尖端形状以及裂纹测量误差等问题进行了研究。 相似文献
2.
吴时红%何双起%陈颖%赵建华 《宇航材料工艺》2007,37(6):124-126
介绍了金属薄板的缺陷类型,建立了超声喷水穿透C扫描系统和检测方法。检测试验结果表明:采用建立的系统和方法能够检测出厚度≤6mm金属薄板中的分层性缺陷。 相似文献
3.
针对发动机工作时受预载荷的叶片受到外物冲击的情况,设计一种面内单轴及双轴预加载装置,开展单轴与双轴不同大小预拉载荷下碳纤维/环氧树脂复合材料(T700/TDE-86)的高速冲击试验,探究预拉载荷对复合材料抗冲击性能的影响,并结合超声C扫描分析预拉载荷对损伤面积的影响。结果表明:面内初始载荷对复合材料层合板抗冲击性能和分层损伤面积有显著影响;预拉载荷会提高靶板的抗弯刚度,减少靶板吸收的能量,减小弹道极限,且在双轴预拉情况下更明显;弹体击穿靶板后分层损伤面积几乎不变,而预拉载荷会减小分层损伤面积,且在双轴预拉情况下更明显。 相似文献
4.
5.
《中国航空学报》2021,34(7):62-72
Delamination represents one of the most severe failure modes in composite laminates, especially when they are subjected to uniaxial compression loads. The evaluation of the delamination damage has always been an essential issue of composite laminates for durability and damage tolerance in engineering practice. Focusing on the most typical and representative elliptical delamination issue, an analytical model simultaneously considering the conservative buckling process and non-conservative delamination propagation process is implemented. Various computational cases considering different delamination depths, directions, aspect ratios, and areas are established, and the predicted results based on the analytical model are carefully compared. Effects of these geometrical delamination parameters on the buckling, delamination propagation, and failure behaviors of composite laminates are thoroughly analyzed, and innovative evaluation principles of the delamination damage have been concluded. It is found that the delamination area is the key factor that truly affecting the failure behaviors of delaminated composites, and the local / global buckling and failure loads show clear linearity with the delamination area, whilst the delamination depth and direction only have slight effects. 相似文献
6.
《中国航空学报》2023,36(2):316-324
This paper presents an experimental investigation of the Mode II delamination resistance of curved CFRP laminates reinforced with Z-pins. A Pre-Hole Z-pinning (PHZ) process is developed to reduce the in-plane damage of the Z-pinned laminates. The microstructural observation of the Z-pinned laminate specimens indicates that the PHZ process can effectively decrease the defects including the Z-pin offset angle and the area of eyelet zone. The influences of the volume fraction and diameter of Z-pin on the fracture toughness and the delamination crack growth rate of the specimens under End Notch Flexure (ENF) loading are then determined experimentally. The test results show that Z-pin increases the interlayer stiffness of the laminate. The delamination crack growth rate is reduced with the increase of Z-pin diameter and volume fraction, and a reduction up to 40% is achieved compared with the specimens without pins. Furthermore, the Mode II fracture toughness is significantly improved with the increase of Z-pin volume fraction. When Z-pin volume fraction increases by 1%, the achieved fracture toughness is about 200% higher compared to the unpinned laminates. 相似文献
7.
8.
综述了碳/环氧复合材料层间增韧的研究现状与发展趋势,着重对碳/环氧复合材料层间增韧方法与性能的关系进行了介绍. 相似文献
9.
范学领%孙秦%菊池正纪 《宇航材料工艺》2008,38(5)
使用重合网格法(S-FEM)分析了混合模态下CFRP层合板分层问题。首先将虚裂纹闭合技术集成到S-FEM程序中,求解了复合材料分层尖端处的应变能释放率。然后把重合网格法数值结果与基于梁理论的计算结果及实验数据进行了比较。结果表明,对于单方向及多方向CFRP复合材料层合板,重合网格法都能够得到更精确的数值,是一种有效的计算复合材料裂纹尖端应变能释放率的方法。 相似文献
10.