薄膜充气管充气展开特性试验

用展开导轨消除因重力产生的摩擦力,在不同充气速率与初始展开角条件下对薄膜材料充气管的充气展开特性进行了试验研究,获得了展开角,以及展开加速度和内气压的变化规律。试验及分析结果表明:充气管的充气膨胀与展开相互独立,充气膨胀过程近似为等压增容过程,折叠部位的气压变化特性与整体气压变化特性差异明显。     

悬筐式蒸发器的结构设计

本文从设计角度对悬筐式蒸发器的结构进行了介绍和总结,并提出了一些结构的改进意见。     

XX—Ⅱ平尾六分量天平的研制

本文是国内第一台六分量部件天平的研制总结,文中对此类天平所遇到的一些棘手问题所采取的一些措施及实验结果作了介绍。     

炭/炭复合材料防氧化涂层研究进展

介绍了近两年国内外开发的几种C/C复合材料高性能抗氧化涂层的微观结构和高温氧化行为,表明SiC-Al2O3-莫来石、SiC晶须增韧陶瓷、硅酸钇等涂层1500℃静态空气环境下均具有长时间防氧化能力,部分涂层还具有优良的抗热震性能。其中采用原位形成法制备的硅酸钇涂层具有极佳的抗氧化性能,可在1600℃空气中对C/C复合材料有效保护200 h。此外,还介绍了部分涂层的失效机理,并就C/C复合材料抗氧化涂层下一步研究重点提出一些见解。     

脉冲式转速表的设计,校验与应用

本文就航空发动机转速测量技术状态进行了简要分析,对适用于超轻型飞机的具有原理、结构简单,造价低等优点的“脉冲式转速表”的设计、校验等进行了详细的论述,并对该原理的推广应用进行了分析讨论。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

Study on the Microstructure and Dielectric Properties of Barium Strontium Titanate Thin Films Prepared by Sol-gel Method

Sr05Ba0.5-xBixTiO3 （BST） thin films were fabricated on a Pt/SiO2/Si substrate by the sol-gel method. Then follows an investigation of the influeoces of bismuth （Bi） on the microstructures and the dielectric properties of Sr0.5Ba0.5-xBixTiO3 （BST） thin films. The microstructures of the BST thin films were examined by the XRD and the TEM techniques. Tetragonal perovskite crystal grains were observed in BST thin films. Increasing Bi^3＋ doping ration in BST will lead to decrease of the grain size. It is found that Bi^3＋ doping decreases the dielectric loss and improves the frequency dispersion of the BST thin films. Not only is compressed the peak of temperature-dependence of dielectric constant of Bi^3＋-doped BST thin films but also moves into the low-temperature region. Moreover, the average Curie tem- perature decreases gradually with the Bi^3＋ contents increasing.     

双温度试验系统方案设计

结合双温度试验系统方案设计,介绍了可编程控制器在温度控制上的应用,有助于增进读者对PLC等的了解。     

利用非交错对称矩阵构造Cartesian认证码

利用特征为2的有限域上非交错对称矩阵构造了一个Cartesian认证码，并计算出其参数。进而，假定编码规则按照均匀的概率分布所选取，计算出了该码被模仿攻击成功的最大概率只和被替换攻击成功的最大概率Ps。     

热暴露对IMI834近α高温钛合金组织和拉伸性能的影响

测试了ＩＭＩ８３４高温钛合金在６００～７５０℃的空气中热暴露１００小时后拉伸性能，利用透射电镜和扫描电镜观察了合金暴露前后的组织变化及拉伸断口，认为表面氧化是造成合金热暴露后塑性下降的主要原因，但基体组织内有序α２相和硅化物的析出变化也在不同程度上造居了合金热暴露后的强度和塑性的下降。