Modelling of Ejecta as a Space Debris Source

When a micro-debris or a micrometeoroid impacts a spacecraft surface, a large number of secondary particles, called ejecta, are produced. These particles can contribute to a modification of the debris environment: either locally by the occurrence of secondary impacts on the components of complex and large space structures, or at great distance by the formation of a population of small orbital debris. This paper describes firstly, the ejecta overall production, and secondly, the lifetime and the orbital evolution of the particles. Finally the repartition of ejecta in LEO is computed. Some results describing the population as a function of size and altitude are presented.     

考虑二次流影响的压缩系统稳定性模型

利用Ａｄｋｉｎｓ－Ｓｍｉｔｈ二次流模型计算得到转子出口截面落后角沿叶高的变化。在压缩系统稳定性模型中考虑叶尖流面落后的角影响，并提出一个新的时滞参数计算公式，计算结果表明，落后角的大小对压缩系统的稳定性影响很大，同时揭示了叶尖间隙对压缩系统稳定性的影响。     

旋转环形截面弯管内流场结构及换热特性

环形截面弯管围绕其中心轴旋转时，同时受到科氏力和离心力作用，弯管内的对流换热更为复杂，本文对旋转环形截面弯管内的流动特性和温度分布进行了数值分析。结果表明：旋转环形截面弯管内的换热特性主要由Dn数，F数（科氏力和离心力之比),Pr数，和δ值（内外径之比）决定；文中给出并分析了在不同δ下流场结构与摩擦系数比随F数的变化特性和随Dn数的变化规律，并给出了在不同δ和Pr数情况下，温度场和管道Nu数随F数和Dn数的变化规律。     

简谐激励下弯曲薄板的非线性运动方程

推导了两端固定和两端简支的弯曲薄板在其支承简谐激励下的运动微分方程,并利用Galerkin方法对其进行了离散化处理。     

基于UG平台的数控电解加工工艺过程模拟

以某型整体叶轮数控电解加工为例,基于UG软件平台,通过二次开发实现其加工工艺过程的模拟,验证数控轨迹,检查工件和阴极间的间隙以及判断是否发生干涉,为数控代码和阴极设计的改进提供依据,减少试验次数。     

利用虚拟仪器实现角速度波动率的采集和处理

利用NI 的PXI-6281高速数据采集卡来完成角速度波动信号的采集,借鉴信号失真度的概念,分析角速度反馈信号的基波和高次谐波大小,求取高次谐波与基波幅值比,作为角速度波动率.     

Fe—10Ni—14Co钢标准状态的组织研究

用透射电子显微镜重点研究了Ｆｅ－１０Ｎｉ－１４Ｃｏ钢的标准处理状态（８３０℃风冷＋—７３℃＋５１０℃Ｓｈ）的微观组织结构。５１０℃回火不同时间，由于Ｍ２Ｃ的析出状态发生变化，钢也由峰时效（５１０℃／１０ｍｉｎ）→过时效（５１０℃／５ｈ）→明显过时效转变。５１０℃５ｈ合会开始发生逆转变。     

谐波传动共轭齿廓的运动学仿真研究

根据包络理论，通过建立谐波齿轮传动共轭齿廓分析的通用数学模型，在已知柔轮齿廓的条件下可求得与之共轭的刚轮理论齿廓的离散点，通过最小二乘拟合的方法求得刚轮的工作齿廓，并通过啮合区段干涉检验法来校验齿廓的重叠干涉，最后通过计算机程序对所求的刚、柔轮工作齿廓进行运动学仿真以验证所求工作齿廓的合理性，还通过实例对程序进行了验证。本文的方法为探索谐波齿轮用新型工作齿廓提供一条可行的途径，并使小速比谐波齿轮传动变得可行。     

Evaluation and improvement of coastal GNSS reflectometry sea level variations from existing GNSS stations in Taiwan

Global sea level rise due to an increasingly warmer climate has begun to induce hazards, adversely affecting the lives and properties of people residing in low-lying coastal regions and islands. Therefore, it is important to monitor and understand variations in coastal sea level covering offshore regions. Signal-to-noise ratio (SNR) data of Global Navigation Satellite System (GNSS) have been successfully used to robustly derive sea level heights (SLHs). In Taiwan, there are a number of continuously operating GNSS stations, not originally installed for sea level monitoring. They were established in harbors or near coastal regions for monitoring land motion. This study utilizes existing SNR data from three GNSS stations (Kaohsiung, Suao, and TaiCOAST) in Taiwan to compute SLHs with two methods, namely, Lomb–Scargle Periodogram (LSP)-only, and LSP aided with tidal harmonic analysis developed in this study. The results of both methods are compared with co-located or nearby tide gauge records. Due to the poor quality of SNR data, the worst accuracy of SLHs derived from traditional LSP-only method exceeds 1?m at the TaiCOAST station. With our procedure, the standard deviations (STDs) of difference between GNSS-derived SLHs and tide gauge records in Kaohsiung and Suao stations decreased to 10?cm and the results show excellent agreement with tide gauge derived relative sea level records, with STD of differences of 7?cm and correlation coefficient of 0.96. In addition, the absolute GNSS-R sea level trend in Kaohsiung during 2006–2011 agrees well with that derived from satellite altimetry. We conclude that the coastal GNSS stations in Taiwan have the potential of monitoring absolute coastal sea level change accurately when our proposed methodology is used.     

轴流压气机转子尖部三维复杂流动Ⅱ——数值模拟研究

在实验研究和理论分析的基础上,对亚声速压气机转子尖部复杂流动做了数值模拟研究,旨在进一步深入研究叶尖间隙和进口总压分布对转子叶尖复杂流动的影响。首先通过对与实验条件相同的转子尖部复杂流动的数值模拟研究,校验了数值模拟结果,并分析了转子尖部复杂流动速度场、压力场和涡量场分布特性。然后通过改变叶尖间隙尺度和进口总压分布,研究了二者对近叶尖复杂流动的影响。研究结果表明:当叶尖间隙小于1%叶片弦长时角区旋涡的发展是导致转子失速的关键;而当叶尖间隙大于2%叶片弦长时叶尖泄漏涡的发展是导致转子失速的关键;改变进口总压分布可以合理地组织转子尖部流动并扩大转子工作裕度。此外,通过观测近叶片吸力面二维涡线的发展趋势可以判断叶尖复杂流动的发展状态。