Estimating the spin axis orientation of the Echostar-2 box-wing geosynchronous satellite

For the first time, the spin axis orientation of an inactive box-wing geosynchronous satellite has been estimated from ground-based optical photometric observations of Echostar-2’s specular reflections. Recent photometric light curves obtained of Echostar-2 over four years suggest that unusually bright and brief specular reflections were occurring twice within an observed spin period. These bright and brief specular reflections suggested two satellite surfaces with surface normals separated by approximately 180°. The geometry between the satellite, the Sun, and the observing location at the time of each of the brightest observed reflections, was used to estimate Echostar-2’s equatorial spin axis orientation coordinates. When considering prograde and retrograde rotation, Echostar-2’s spin axis orientation was estimated to have been located within 30° of either equatorial coordinate pole. Echostar-2’s spin axis was observed to have moved approximately 180° in right ascension, within a time span of six months, suggesting a roughly one year spin axis precession period about the satellite’s angular momentum vector.     

INFLUENCE OF THE CRYSTAL GROWTHORIENTATION ON THE MICROSTRUCTUREIN HYPORAPIDSOLIDIFICATION

ＩＮＦＬＵＥＮＣＥＯＦＴＨＥＣＲＹＳＴＡＬＧＲＯＷＴＨＯＲＩＥＮＴＡＴＩＯＮＯＮＴＨＥＭＩＣＲＯＳＴＲＵＣＴＵＲＥＩＮＨＹＰＯＲＡＰＩＤＳＯＬＩＤＩＦＩＣＡＴＩＯＮＪｉａｎｇＣｈｅｎｇｂａｏ；ＨｕＨａｎｑｉ；Ｗａｎｇｐｅｉｊｕｎ；ＺｈａｎｇＨｕ（Ｂｅ...     

丁羟推进剂拉伸断裂行为的扫描电镜研究

利用扫描电镜及附属微型动态拉伸装置实验手段，对丁羟基复合固体推进剂进行了断口微观形貌观察和电镜微型拉伸试件在应变状上的断裂行为分析。结果表明，从推进剂拉伸力学行为的微观结构变化以预示其宏 同力学性能，改善丁羟推进剂粘合剂与固体颗粒之间的界面性质，是固体推进剂力学性能的一个重要方向。     

GH169合金细晶锻造工艺研究

为了提高涡轮盘的强度和低周疲劳性能,要求锻件具有ASTM10级以上的细晶组织国外在大型压力机上采用低温大变形锻造和直接时效热处理以获得性能良好的细晶锻件,而我国则试图采用锻锤生产GH169合金涡轮盘锻件,因此,需要探索适合国情的GH169合金细晶锻造工艺。根据以往的研究,δ相对GH169合金的显微组织有明显影响,因而可     

Study on the Microstructure and Dielectric Properties of Barium Strontium Titanate Thin Films Prepared by Sol-gel Method

Sr05Ba0.5-xBixTiO3 （BST） thin films were fabricated on a Pt/SiO2/Si substrate by the sol-gel method. Then follows an investigation of the influeoces of bismuth （Bi） on the microstructures and the dielectric properties of Sr0.5Ba0.5-xBixTiO3 （BST） thin films. The microstructures of the BST thin films were examined by the XRD and the TEM techniques. Tetragonal perovskite crystal grains were observed in BST thin films. Increasing Bi^3＋ doping ration in BST will lead to decrease of the grain size. It is found that Bi^3＋ doping decreases the dielectric loss and improves the frequency dispersion of the BST thin films. Not only is compressed the peak of temperature-dependence of dielectric constant of Bi^3＋-doped BST thin films but also moves into the low-temperature region. Moreover, the average Curie tem- perature decreases gradually with the Bi^3＋ contents increasing.     

7075铝合金在超塑处理和拉伸过程中的显微组织变化

 研究了 70 75铝合金在超塑性预处理和拉伸过程。结果表明 ,合金经过固溶处理炉冷→轧制预处理后 ,形成 1～ 2 μm的胞块组织。在超塑拉伸过程中胞块发生回复和再结晶 ,形成细晶组织 ,使合金获得优异的超塑性性能     

扫描隧道显微镜对粘胶基碳纤维表面微观结构的研究

用扫描隧道显微镜（STM）对粘胶基碳纤维（RCF）表面的微观结构进行了研究，首次获得了原子级的RCF图像，对其原子间距作了精确地量化，并且尝试着将所得到的图像与高定向降解石墨（HOPG）相比较，以期对RCF的微观结构有更深入的了解，在原子级尺度上，发现了原子排列并不规则的石墨状结构，二维视图量化结果表明：相邻原子间距为0．142nm，最近六圆环中心的距离是0．253nm。     

SCR技术制备A2017半固态材料及其触变性能的研究

单辊搅拌技术 (SCRShearing/CoolingRollProcess)技术制备的A2 0 17半固态材料比常规铸造坯组织优良 ;SCR技术制备的A2 0 17半固态材料在 5 30～ 5 70℃范围内 ,可以进行触变成形 ;半固态成形平均屈服强度比热加工时的屈服强度低 10MPa ;A2 0 17半固态材料触变过程分为四个阶段 ,稳定触变阶段A2 0 17半固态材料的触变性能稳定 ,半固态加工时容许的最大加工变形范围为 6 4 %～ 72 %。     

无损检测的内涵演变及其在质量控制中的作用

就无损检测的内涵如何从探伤演变到评价及无损检测在质量控制中的应有作用作了叙述,希望对相关人员开拓思路、提高工作质量有所裨益.     

TC21钛合金的微观组织对力学性能的影响

研究了两相钛合金TC21关于两种不同微观组织(片状组织和网篮组织)的拉伸性能、断裂韧性和疲劳裂纹扩展性能.结果显示:片状组织相比网篮组织有相近的拉伸强度,但塑性较差;两者的韧性相差不大,但增韧机理不同;网篮组织在中低速扩展区的扩展速率和片状组织几乎相同,但在较高速扩展区显示略低的扩展速率;加载方向对两种组织的疲劳裂纹扩展速率基本无影响;和其他钛合金类似,TC21在Paris区存在转折.