Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

单刻线样板检定装置测量不确定度分析

分析了单刻线样板检定装置的测量不确定度，并分析了用该检定装置检定的单刻线样板的不确定度。     

废气排放塔尾流区随机游动扩散模拟研究

本文对一种建筑结构与形式特异的废气排放源－过江隧道风井塔，进行了如下研究：（１）在环境风洞中通过风井塔后流场的测量，分析给出塔后尾流特征，并进行示踪气体扩散模拟试验和烟云照相；（２）在上述工作基础上，建立一个先进的随机游动扩散模式，模拟尾流区污染物扩散的基本规律，模式计算结果与实验结果吻合较好。建筑物的存在使得地面最大浓度增大３￣４倍，且出现位置离源更近。研究表明，随机游动方法研究对有明显湍流不均     

高速风洞引射式进排气动力模拟试验研究

为了测定具有埋入式进气道的某航弹发动机进排气对航弹的气动影响量 ,采用引射式动力模拟器在FL 7高速风洞 ,首次在国内成功地进行了高速风洞进排气动力模拟试验。试验模型缩比为 1∶1 0 ,M =0 .7,P0j/P∞ =2 .62 ,Cφ=0 .79。试验结果表明 ,有动力后XD,CL,CD增加 ,Cma减少。试验表明在高速风洞中对于小尺寸的试验模型 ,采用引射式动力模拟器开展进排气动力模拟试验是一种简便适用的好方法     

动力失效对起飞纵向气动特性影响数值研究

研究民用飞机动力失效对飞机起飞阶段纵向气动特性的影响规律及其机理,对保证飞机有效操纵和安全飞行具有重要意义.采用在点对点多块结构化网格系统上求解三维可压缩雷诺平均N-S方程的数值方法,研究发动机动力失效对某民用飞机起飞构型纵向气动特性的影响.通过DLR-F11模型验证研究方法对民用飞机高升力构型气动特性的预测能力;针对安装动力短舱的某翼吊涡扇发动机民用飞机起飞构型,通过对比其发动机在正常工况和失效时飞机气动特性的差异,得出动力失效对飞机纵向气动特性的影响规律及机理.结果表明:动力失效后,不但溢流效应会使飞机阻力系数增大;还会导致发动机进、排气特性较正常工作状态明显不同,恶化短舱附近流场,对飞机的升力、失速特性带来不利影响.     

Cross-sectional deformation behavior of double-ridged rectangular tube with fillers in different stages of H-typed bending

The bent double-ridged rectangular tube (DRRT) with high forming quality is helpful to improve the microwave transmission accuracy. For reducing the cross-sectional deformation in the H-typed bending process, in addition to using rigid mandrel to support the inside of tube, ridge groove fillers are also added to restrict the deformation of ridge grooves. Because of the change of stress and strain state of bent tube in bending, rigid mandrel retracting and specially twice-springback stages, and the springback of fillers, the cross-sectional deformation of tube in each stage may be different. Therefore, based on the ABAQUS platform, the finite element models (FEM) for H-typed bending, mandrel retracting and twice-springback stages of H96 DRRT with fillers were established and validated. It is found that, for the height and width deformation of tube and spacing deformation of ridge grooves, retraction of mandrel can make the distribution of these deformations more uniform along the bending direction. The first springback can reduce these deformations significantly, which should be emphasized. But the second springback only increases them by less amount, which can be ignored. The smaller height deformation of ridge groove and filler can be neglected.     

螺旋槽端面气膜密封结构高温特性研究

为了研究螺旋槽端面气膜密封结构在高温下的密封性能,建立了高温密封分析数学模型,研究了螺旋槽气膜密封的气膜温度、压力以及端面变形分布规律,在此基础上探讨了螺旋槽气膜密封的热变形机理,并进一步分析了不同密封压力、转速、环境温度下热效应对开启力和泄漏率的影响。结果表明:在高压、高速条件下,热效应使端面形成发散间隙,导致开启力减小,泄漏率增加;在低压、高速条件下,热效应使端面形成收敛间隙,导致开启力及泄漏率增大。对于螺旋槽端面气膜密封结构,环境温度的升高对端面变形的影响不明显,且环境温度从300 K升至550 K时,考虑端面热效应的开启力减小4%,泄漏率减少36%。     

基于数值模拟的翼身融合布局飞机上悬式发动机布置技术

发动机进排气对飞机气动特性具有重要影响。为了评估翼身融合布局（BWB）飞机上悬式发动机不同布置方式对全机气动特性的影响,首先开展了发动机短舱进排气与全机流场耦合的数值模拟技术研究,验证了计算方法的正确性。在此基础上,针对发动机安装于翼身升力面之上的BWB运输类飞机,开展飞机巡航飞行条件下,发动机不同支撑高度下沿流向及展向不同安装位置的进排气与全机流场耦合数值模拟,评估发动机不同布置方式对全机气动特性的影响,形成发动机不同布置方式影响的规律性结论。     

基于数值模拟的轴对称矢量喷管内流特性研究

采用三维有粘定常程序计算了轴对称矢量喷管的内流特性,研究了尺寸缩比、冷热态的影响,并与冷态缩比模型矢量特性试验结果进行了对比;给出了设计工况的内流特性,讨论了几何矢量角、喷管落压比对内流特性的影响.研究结果表明,尺寸缩比、冷热态对内流特性的影响均很小,冷态缩比模型试验结果可以真实地反映设计工况的内流特性,轴对称矢量喷管在设计工况下具有良好的内流特性,并且几何矢量角、喷管落压比对内流特性均有影响.      

间隙流触发压气机内部流动失稳机制及周向槽扩稳机理

利用高频响动态压力传感器对某低速轴流压气机转子的失速先兆和顶部流场进行了详细的测试,探明该压气机内部存在与叶顶间隙泄漏流相关的突发型失速先兆,对压气机转子内部流场进行了单通道定常和非定常数值模拟,详细分析了压气机内部流动失稳过程中顶部流场结构的变化,揭示顶部间隙泄漏流触发轴流压气机内部流动失稳机理.在此基础上,利用周向槽处理机匣结构对顶部间隙泄漏流进行控制,并探讨了周向槽处理机匣结构提高压气机稳定工作裕度机理.