三旋流器加装外套环对燃烧性能的影响

对带有两种不同头部结构（基准型为方案1,头部加装外套环为方案2）的三旋流单头部燃烧室进行了研究,对有两种头部结构的燃烧室进行了流场和燃烧场的数值模拟,在相同的进口试验条件下,用燃气分析法和15点测温耙分别测量了两种头部的燃烧效率、出口冒烟数和出口温度场.结果表明:三旋流器的燃烧效率超过了99.7%,加装外套环后其流场、温度场分布均较基准型有所改善,回流区更加饱满,油气混合和燃油雾化效果增强,出口温度分布系数（OTDF）和出口冒烟数分别降低了36%和25%.      

高强Al-Cu-Li-X铝锂合金2A97三级时效工艺及性能研究

以新型高强Al-Gu-Li-X铝锂合金2A97为研究对象,通过拉伸试验研究两种三级时效工艺及其改型工艺对合金性能的影响.结果表明,含有δ′相二次析出过程的三级时效和含有δ′相回溶过程的三级时效处理合金的强度和塑性达到T6峰值时效水平,三级时效改型工艺由于增加变形使前者合金的强度升高,塑性降低,使后者的强度显著提高.三级时效和单级时效合金的主要显微组织有δ′相、θ″/θ′相和T1相.三级时效改型工艺由于增加变形促进δ′相析出和δ′相回溶,同时变形促进T1相析出,从而改变了主要强化相δ′相和T1相的数量.     

突跃型与平滑型斜爆震波起爆机制数值模拟

采用带有化学反应的Euler方程,对突跃型与平滑型2种形态的斜爆震波(ODW)在起爆机制和结构特点等方面的差异进行了研究.结果表明:斜激波(OSW)后是否存在亚声速区是判定斜爆震形态的依据.当波后火焰抬升斜激波面使得亚声速区存在时,横向激波与三波点结构就会出现并形成突跃型斜爆震.当波后所有区域皆为超声速区时,波后火焰燃烧无法影响到上游激波面,则会形成平滑型斜爆震.通过斜激波关系式给出了横向激波形成所需的临界斜激波角度,只有当斜激波角度大于此临界角度时才能形成突跃型斜爆震波,反之则形成平滑型斜爆震波.      

油气比及进口参数对三级旋流器燃烧室性能的影响

对三级旋流器燃烧室进行了常压试验研究.研究首先设计研制了三级旋流器燃烧室模型和试验系统,然后在此基础上开展了不同进口速度、进口温度和油气比等参数影响三级旋流器燃烧室的流阻特性、点火特性、贫油熄火特性和燃烧效率特性等性能的试验研究.结果表明:该三级旋流器燃烧室可以在不同试验工况下顺利点火和稳定工作,点火性能基本不受进口速度的影响;总压损失系数随进口速度的增加而增大,而流阻系数随速度的增加而减小,燃烧室流动未进入"自模状态";随着进口温度的增加,点火、贫油熄火性能变好,燃烧效率提高.     

关于平面激波在凹两段楔面上的传播

众所周知,当一平面激波同任意形状的障碍物相互作用时,将产生十分复杂的波系,其中激波在曲面壁上的绕射和反射,将产生非定常波系。关于平面激波在凹圆柱壁面上的传播,我们可以用一连串、长度为无限小的楔面所构成的多边形来近似和代替凹圆柱面,因此分析和研究激波在两段楔面上反射和绕射的目的在于得出激波在圆柱壁面以及其它较复杂形状壁面上的传播规律。本文采用马赫-曾德干涉仪在激波管上进行光测模型实验。根据所拍摄的流场干涉图像,以分析其波系的演变过程及传播规律,得到有关流场的密度分布和压力分布,更为重要的是给出流场参数的定量结果。     

高温升直流燃烧室燃烧特性数值研究

为了研究高温升直流燃烧室燃烧特性,建立了带三级涡流器的高温升直流燃烧室物理模型,采用稳态雷诺平均N-S方程的化学反应流数值模拟的方法,开展Ⅱ、Ⅲ级径向涡流器旋向、主燃孔和掺混孔特征参数对高温升直流燃烧室的流场及燃烧特性的影响研究。涡流器能够实现火焰筒头部回流区的产生,同时实现主油路燃油的气动雾化和掺混。主燃孔的射流影响回流区的结构,同时主燃孔射流部分进入主燃区,能够保证主燃区的油气比。掺混孔的射流轨迹影响掺混区的流场和出口温度分布。10种方案燃烧室的温升和总压损失系数均达到设计要求,Mode-1-tx、Mode-3、Mode-3-tx、Mode-4-tx四种方案燃烧室周向温度分布系数(Overall temperature distribution factor,OTDF)达标,而径向温度分布系数(Radial temperature distribution factor,RTDF)略高于设计指标,Mode-5-tx方案燃烧室出口温度系数OTDF=0.178和RTDF=0.061均达标,燃烧室出口温度分布品质较好。     

混合三元系超大集

对于三类混合三元系超大集Ti-OLGD（v）（i=1,2,3）,T1-OLGD（v）和T2-OLGD（v）的存在谱已经完全解决了,而对于T3-OLGD（v）的存在性问题,所知结果很少。本文利用代数和组合设计相结合的方法,主要利用有限域的相关知识,对于T3-OLGD（q-1）（q为素数幂）,给出了一种新的构造方法,从而得到了一系列的结果。     

Rosetta Asteroid Targets: 2867 Steins and 21 Lutetia

In preparation for the flyby of the Rosetta spacecraft, the state of the knowledge of 21 Lutetia and 2867 Steins obtained by ground based observations is reported. Preliminary determination of shape and/or size, rotational properties and taxonomic types are presented for both asteroids. The dusty environment of the targets has been studied in order to help in defining safe fly-by trajectories without the risk of damaging collisions. The expected science return from the asteroid fly-by is also discussed.     

A sample collector for robotic sample return missions III: Impact survivability studies

Laboratory impact tests have been performed on experimental versions of a proposed robotic sample collector for extraterrestrial samples. The collector consists of a retractable aluminum ring containing an impregnable silicone compound that is pressed into the surface of the body to be sampled. As part of a comprehensive program to evaluate this idea, we have performed tests to determine if the samples embedded in the collector medium can survive the impact forces experienced during direct reentry, such as that of the recent Genesis sample return mission. For the present study, samples of sand, rock, glass, and chalk were subjected to decelerations of 1440–2880 g using drop tests. We found that even the most fragile samples, chosen to be representative of a wide range of the types of materials found on the surface of asteroids that have currently been studied, can withstand impacts of the intensity experienced by a sample return capsule during direct reentry.     

Contingency target assessment,trajectory design,and analysis for NASA’s NEA scout solar sail mission

The presented study examines contingency target selection and trajectory design for NASA’s Near-Earth Asteroid Scout mission under the assumption of a missed lunar gravity assist. Two previously considered asteroids are selected as potential targets for the given scenario based on favorable orbital characteristics for launch dates ranging from June 27, 2020 through July 26, 2020. Initially, a simplified circular restricted 3-body problem + ideal solar sail model is utilized to survey trajectory options for a month-long launch window. Selected solutions from this data set are then converged in an N-body ephemeris + non-ideal sail model. Results suggest that NEA Scout can still perform asteroid rendezvous mission under the missed lunar gravity assist scenario with new targets, 2019 GF1, 2018 PK21, and 2007 UN12, based on the target launch dates. Further target assessment is carried out for 165 days beyond the current June 27, 2020 launch date.