Review and propositions for the sliding/impact wear behavior in a contact interface

A thermal-solid-liquid complex operational environment induces structural interface developing a typical coupling sliding/impact wear behavior. It results in contact damage until systems fail, which may cause significant economic losses and catastrophic consequences. The key point of solving this problem is to reveal the coupling damage mechanism of the sliding/impact behavior in typical systems and life characterization under a complicate evolving environment. This has been a hot topic in the area of mechanical reliability. The main work in this paper can be concluded as follows. Firstly, the main industries in which the “sliding/impact behavior” takes place have been introduced. Then, existing studies on the wear mechanism and degree analysis are presented, which includes surface morphology analysis, wear debris analysis, and wear degree measurement. Meanwhile, existing problems in theoretical modeling and experiments in current research are summarized, so as to point out a bright direction for future research on wear prediction. They include interface contact modeling, mathematic coupling mechanism modeling, wear equation establishment, and wear life characterization, which can provide some new ideas for improving the existing studies on the sliding/impact wear behavior.     

复合材料层板中就位横向拉伸强度的研究

本文利用弹性力学和断裂力学方法对纤维增强复合材料的横向拉伸强度进行了分析，其中考虑了９０度开裂层厚度和开裂邻层的约束效应的影响，推导出正交各向异性对称铺层中昨合就位横向拉伸强度的数学表达式，得出开裂层的厚度和约束邻层铺设角对就位横向拉伸强度都有影响的结论，理论计算与Ｆｌａｇｇｓ实验结果吻合较好。     

现代激励理论在规范地方政府行为中的作用研究

分析现代激励理论在研究地方政府行为中的作用，并运用现代激励理论提出了规范地方政府经济行为的若干建议。     

丁羟推进剂拉伸断裂行为的扫描电镜研究

利用扫描电镜及附属微型动态拉伸装置实验手段，对丁羟基复合固体推进剂进行了断口微观形貌观察和电镜微型拉伸试件在应变状上的断裂行为分析。结果表明，从推进剂拉伸力学行为的微观结构变化以预示其宏 同力学性能，改善丁羟推进剂粘合剂与固体颗粒之间的界面性质，是固体推进剂力学性能的一个重要方向。     

CVD-Si3N4陶瓷及其复合材料氧化行为研究进展

概述了CVD—Si3N4陶瓷及其复合材料在干燥氧气下的氧化行为。Si3N4陶瓷在高温下氧化时，除生成SiO2保护膜外，还生成一薄层比SiO2膜更优异的氧气扩散阻挡层(Si—O—N化合物层)，该层具有优异的抗氧化性能。介绍了两种氧化机制模型，同时分析了温度、杂质等对CVD—Si3N4陶瓷氧化行为的影响。     

TC21钛合金的微观组织对力学性能的影响

研究了两相钛合金TC21关于两种不同微观组织(片状组织和网篮组织)的拉伸性能、断裂韧性和疲劳裂纹扩展性能.结果显示:片状组织相比网篮组织有相近的拉伸强度,但塑性较差;两者的韧性相差不大,但增韧机理不同;网篮组织在中低速扩展区的扩展速率和片状组织几乎相同,但在较高速扩展区显示略低的扩展速率;加载方向对两种组织的疲劳裂纹扩展速率基本无影响;和其他钛合金类似,TC21在Paris区存在转折.     

细长体分离起始点的实验研究

本文实验研究了细长体模型在中等迎角下的初始分离问题。观察了不同头部形状的细长体在不同迎角下的分离流态。考察并分析了分离起始点的性质。观察到开式分离的存在,实验结果分析认为开式分离可以起始于正常点。此外,在钝头和尖头模型上都出现了螺旋点形式的头部涡。它们或是闭式分离的起始点,或是奇点型开式分离的起始点。     

单向玻璃纤维增强环氧树脂低温冲击拉伸性能的试验研究

 在经改进后配有低温装置的杆-杆型冲击拉伸装置上,对单向玻璃纤维增强环氧树脂在室温、-50℃、-100℃和-150℃的冲击性能进行了研究。结果表明该材料有温度相关性,所研制的装置性能良好,便于应用。     

粉末高温合金FGH96惯性摩擦焊接头常温力学性能分析

第二代粉末高温合金FGH96是采用损伤容限设计思想研制的新型粉末高温合金,是当前750℃工作条件下满足高推比、高燃效发动机使用要求的涡轮盘、环形件和其他热端部件的理想材料.结合FGH96惯性摩擦焊接头的组织特征和强化相γ′数量分析接头的显微硬度和常温拉伸性能.结果表明,FGH96惯性摩擦焊接头具有良好的常温力学性能.     

Effect of curing condition on bonding quality of scarf-repaired composite laminates

Both single-face vacuum bag curing (SVC) and double-face vacuum bag curing (DVC) can be used in scarf repair of composite structures. But different curing conditions caused by the sealing state may affect the bonding quality of scarf-repaired structures. In this paper, the effect of curing condition on bonding quality of scarf-repaired laminates was experimentally investigated in terms of surface profiles, moisture absorption curves and section profiles. In order to further explore the moisture absorption mechanism, finite element model of the repaired laminates using DVC was established with moisture diffusion of both the adhesive and composite laminates considered. This model was verified by experimental results. Based on the model of DVC case, the model of SVC case was built by changing moisture absorption parameters of the adhesive. Results show that SVC reduces the bonding quality, mainly reflecting in more adhesive inner voids and patch-to-parent dislocation. And SVC increases moisture absorption rate and moisture equilibrium content of the adhesive, and its effect on the former is far greater than that on the latter.