薄膜充气管充气展开特性试验

用展开导轨消除因重力产生的摩擦力,在不同充气速率与初始展开角条件下对薄膜材料充气管的充气展开特性进行了试验研究,获得了展开角,以及展开加速度和内气压的变化规律。试验及分析结果表明:充气管的充气膨胀与展开相互独立,充气膨胀过程近似为等压增容过程,折叠部位的气压变化特性与整体气压变化特性差异明显。     

智能天线结构模糊自适应变形控制实验研究

基于dSPACE半物理仿真系统和所研制的压电作动器,设计并构建了智能天线结构实验平台,进行了结构变形控制实验研究。实验中采用常规PID作为基本控制方法,并在此基础上设计了一种模糊自适应PID控制器,将两种方法对应的不同控制效果进行了对比。结果表明:在所给的实验条件下,基于压电材料可实现对智能天线结构变形的控制,作动器控制变形量最大可达166μm;两种控制方法均可对结构变形进行控制,模糊自适应方法的绝对位置控制精度达到±0.5μm;应用模糊自适应PID控制方法对结构进行变形控制,较之常规PID控制方法能够降低系统响应的超调量,缩短稳定时间,提高控制精度,得到更好的控制过程。     

空间智能桁架自适应模糊振动控制

研究了一种基于自适应模糊控制器的空间智能桁架振动控制方法。在考虑剩余模态影响的条件下建立了空间智能桁架的独立模态空间振动控制方程,并对自适应模糊控制器作改进,证明了控制系统的稳定性。仿真结果表明:该自适应模糊控制器可有效抑制桁架振动,控制效果明显优于传统模糊控制,同时能抑制控制溢出和观测溢出。     

谈我院综合教学楼的设计

本文简明扼要地介绍了我院新建综合教学楼在有限的建筑用地范围内，为满足各项功能要求的建筑设计思路及结构上的处理方法。     

复合材料叠层结构剖面翘曲修正理论

 首先假设复合材料叠层结构的面内位移沿厚度方向为直线分布,然后根据剪切变形进行连续修正,获得逐步升高的各阶翘曲位移分布函数。文中以叠层梁为例,应用最小势能原理导出其静力方程和力的边界条件。在长度方向则采用升阶谱位移函数,进行了数值计算。所得叠层梁的位移和应力分布的数值结果与精确解相比,表明本文方法有很好的收敛性。     

两种镁合金的化学处理

对AZ91D和AM50合金进行化学处理，用SEM和电化学方法来分析化学转化膜的表面形貌及在腐蚀性电解质中的稳定性。结果表明，铬酸盐处理时，AM50合金较AZ91D合金的成膜反应容易进行，成膜均匀，在3．5％NaCI水溶液中耐蚀性能好；而磷酸盐处理时，结果恰恰相反，AZ91D合金转化膜的性能优于AM50合金的膜。     

基于超纯水电解加工的水解离机理研究

介绍了一种以超纯水为电解液的电解加工工艺方法,即超纯水电解加工技术.研究了阳离子交换膜在超纯水中的水解离机理及工作特性,分析其在超纯水电解加工过程中的作用机理,并进行了水解离试验研究.结果表明：电流密度达到了3.7 A/cm^2,电场强度约为2 MV/m,已进入微细电解加工去除材料要求范围,为超纯水微细电解加工的应用奠定了基础.     

浇注温度和细化剂对K4169高温合金微观组织的影响

研究了降低浇注温度或加入细化剂后 ,K4 16 9合金晶粒细化的微观组织、夹杂及缩松等的变化。发现同样加或不加细化剂条件下 ,浇注温度越低 ,一次枝晶主轴长度和二次枝晶臂距越小。而同一浇注温度下 ,化学法细晶试样一次枝晶主轴长度较普通试样的短 ,而二者的二次枝晶臂距无明显差别。晶粒细化后 ,晶粒形态由普通铸造组织中的树枝晶向细晶组织中的粒状晶转变 ,且合金中主要元素的偏析减轻 ,这均有利于提高细晶铸件机械性能。MC型碳化物和Laves相的尺寸、数量和形貌在晶粒细化前后变化不大。铸件中加入微量细化剂不形成夹杂 ,不改变合金相组成。此外 ,加细化剂不仅可使晶粒细化 ,同时铸件中的缩松大大减少     

A compliant polymorphing wing for small UAVs

This paper presents the development of a novel compliant polymorphing wing capable of chord and camber morphing for small UAVs. The morphing wing can achieve up to 10% chord extension and ±20° camber changes. The design, modeling, sizing, manufacturing and mechanical testing of the wing are detailed. The polymorphing wing consists of one continuous front spar fixed to the fuselage and a rear spar on each side of the wing. Each rear spar can translate in the chordwise direction (chord morphing) and rotate around itself (camber morphing). A flexible elastomeric latex sheet is used as the skin to cover the wing and maintain its aerodynamic shape whilst allowing morphing. The loads from the skin are transferred to the spars using the compliant cellular ribs that support the flexible skin and facilitate morphing. Pre-tensioning is applied to the skin to minimize wrinkling when subject to aerodynamic and actuation loads. A rack and pinion actuation system, powered by stepper motors, is used for morphing. Aero-structural design, analysis and sizing are conducted. Performance comparison between the polymorphing wing and the baseline wing (non-morphing) shows that chord morphing improves aerodynamic efficiency at low angles of attack while camber morphing improves efficiency at high angles of attack.     

Electric potential structures of auroral acceleration region border from multi-spacecraft Cluster data

This paper studies an auroral event using data from three spacecraft of the Cluster mission, one inside and two at the poleward edge of the bottom of the Auroral Acceleration Region (AAR). The study reveals the three-dimensional profile of the region’s poleward boundary, showing spatial segmentation of the electric potential structures and their decay in time. It also depicts localized magnetic field variations and field-aligned currents that appear to have remained stable for at least 80?s. Such observations became possible due to the fortuitous motion of the three spacecraft nearly parallel to each other and tangential to the AAR edge, so that the differences and variations can be seen when the spacecraft enter and exit the segmentations, hence revealing their position with respect to the AAR.