A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

自由飞试验模型惯性矩的测定

作者根据多年来自由飞试验的实践,叙述了自由飞模型惯性矩的调试、计算、误差分析与处理的经验与方法。     

J—7LP飞机1：6遥控模型失速尾旋试验

对无动力J—7LP动力学缩比模型进行了遥控试飞,以研究其失速尾旋特性,全偏平尾和方向舵可使模型进八尾旋,舵面全回中即可从各种尾旋中改出。偏转副翼对尾旋特性有明显的影响。     

域外刑事评议程序之比较研究

刑事评议程序是介于庭审程序和宣告程序之间的一个重要程序,它既是庭审的自然延续,又是裁判结论形成的前提和基础。然而,欲保证刑事评议程序的正常运行,刑事评议主体之独立必须得到保证;刑事评议之客体还应被全面考虑,并对其进行细化,以确保刑事评议的针对性和有效性,防止出现"估堆"现象。本文以域外刑事评议程序为对象,从评议的主体、客体等角度进行梳理,得出规律性的认识,以期对我国关于刑事评议的立法有所裨益。     

炉渣滤床技术处理亚麻生产废水

为了确定处理包头亚麻厂亚麻生产废水的设计方案，设计之前在现场进行了生产试验。在包头亚麻厂污水处理站，模拟炉渣滤床制造了3米高的炉渣滤层，滤渣从工厂锅炉房取用，将实际排放的亚麻煮漂车间、细纱车间、粗纱车间的生产废水混合后，通过炉渣滤层过滤处理，处理后出水由厂化验室和包头环保局化验。试验结果表明，处理后的排水各项指标完全达到国家排放标准。该工艺处理费用低，运行效果稳定，管理简便，具有明显的经济效益、环境效益和社会效益。     

飞机主操纵系统疲劳试验载荷谱小操纵位移频次问题研究

针对飞机全机主操纵系统疲劳试验载荷谱中小操纵位移频次影响问题进行了分析和讨论,确定了某机全机主操纵系统小操纵位移频次的级别。同时,在原某机全机主操纵系统疲劳试验载荷谱的基础上再次对其小操纵位移频次进行了计算,去掉了这一级别以下对全机主操纵系统疲劳试验无影响的小操纵位移频次,从而完善了主操纵系统疲劳试验载荷谱。另外,对小操纵位移频次问题研究结果在其全机主操纵系统疲劳试验中的实施效果进行了阐述。     

400kN振动台承力钢架的研制

文章中介绍的400kN 承力钢架是用来作船罩联合试验的承力机构,具有结构庞大、复杂的特点,对自振频率有一定要求,文章介绍了该设备研制过程中的设计、计算、加工及安装工艺技术等。     

低空突防任务下综合飞行/推进系统的建模与仿真

建立了综合飞行／推进系统的数学模型，介绍了飞机全维非线性数学模型和涡轮风扇发动机非线性部件级数学模型的建模及综合方法。对飞机执行地形中随任务时，飞行员调节飞行速度的方法与基于总能量的调节飞行速度的方法进行了比较。结果表明，基于总能量的方法比飞行员直接控制飞行速度能够减小发动机的燃油消耗，降低发动机的磨损，进而可以增加飞机的航程，延长发动机的使用寿命。     

掠海飞行导弹击水概率的仿真研究

本文对掠海导弹的击水概率问题进行了研究,提出了用均匀设计、Monte—Carlo法和逐步回归法建立击水概率预报公式的仿真方法,并结合某型号的反舰导弹进行计算,得到了满意的结果。本文还利用表观频率和表观频谱的概念,建立起飞航导弹的背景干扰——海浪和阵风的数学模型,并用波叠加法进行了数字仿真。     

无人机自由编队飞行的补偿模糊神经网络控制

为了克服当前提出的无人机编队飞行的不足，提出一种新的无人机编队飞行概念——自由编队飞行，制定了相关的避让规则，用补偿模糊神经网络进行训练，实现自由编队飞行的补偿模糊神经网络控制。仿真显示，编队飞行的飞机能按照规则自主改变航路进行避让，表明了该方法的有效性。