A survey of safety separation management and collision avoidance approaches of civil UAS operating in integration national airspace system

Recent years have witnessed a booming of the industry of civil Unmanned Aircraft System (UAS). As an emerging industry, the UAS industry has been attracting great attention from governments of all countries and the aviation industry. UAS are highly digitalized, informationized, and intelligent; therefore, their integration into the national airspace system has become an important trend in the development of civil aviation. However, the complexity of UAS operation poses great challenges to the traditional aviation regulatory system and technical means. How to prevent collisions between UASs and between UAS and manned aircraft to achieve safe and efficient operation in the integrated operating airspace has become a common challenge for industry and academia around the world. In recent years, the international community has carried out a great amount of work and experiments in the air traffic management of UAS and some of the key technologies. This paper attempts to make a review of the UAS separation management and key technologies in collision avoidance in the integrated airspace, mainly focusing on the current situation of UAS Traffic Management (UTM), safety separation standards, detection system, collision risk prediction, collision avoidance, safety risk assessment, etc., as well as an analysis of the bottlenecks that the current researches encountered and their development trends, so as to provide some insights and references for further research in this regard. Finally, this paper makes a further summary of some of the research highlights and challenges.     

Optimization of bits allocation and path planning with trajectory constraint in UAV-enabled mobile edge computing system

In this paper, an Unmanned Aerial Vehicle (UAV) enabled Mobile Edge Computing (MEC) system is studied, in which UAV acts as server to offer computing offloading service to the Mobile Users (MUs) with limited computing capability and energy budget. We aim to minimize the total energy consumption of MUs by jointly optimizing the bit allocation for uplink, computing at the UAV and downlink, along with the UAV trajectory in a unified framework. To this end, a trajectory constraint model is employed to avoid sudden changes of velocity and acceleration during flying. Due to high-order information in use, we lead to a more reasonable nonconvex optimization problem than prior arts. An Alternating Direction Method of Multipliers (ADMM) method is introduced to solve the optimization problem, which is decomposed into a set of easy sub-problems, to meet the requirement on the efficiency in edge computing. Numerical results demonstrate that our approach leads a smoother UAV trajectory, significantly save the energy consumption for UAV during flying.     

某型无人直升机遥控系统BIT技术研究与实现

机内测试 (Built- In Test,简称 BIT)是一种能显著改善系统或设备测试性和诊断能力的重要技术手段。文中研究如何在遥控系统中运用 BIT技术来提高其测试性 ,并提出了一种分层测试方案 ,研究成果已应用于某型无人驾驶直升机 ,满足了遥控系统的测试性要求     

开放式飞行任务规划方法

本文给出了一种基于分布式黑板结构的开放式飞行任务规划方法，简要叙述了飞行器飞行任务规划的概念和其独特要求，并对飞行任务规划的数据预处理、知识表达、规划方法作了深入的探讨。最后介绍了分布式黑板的结构和运行方式。     

某无人直升机扩频通信系统捕获方案设计

讨论一种用于某无人机直序扩频通信测控系统的PN码捕获方案。根据该系统的技术指标要求,针对无人机信道的特殊性,采用匹配滤波器进行PN码的相关处理,并运用检测后积分和二次驻留的方法提高检测概率降低虚警概率。在进行详细理论分析的基础上,运用Cadence公司的SPW系统仿真软件,将该系统在高斯白噪信道和无人机信道下进行对比性系统仿真,仿真结果以及FPGA实测结果均表明,上述两种方法有效地提高了系统性能。     

基于阻力气动特性计算的飞艇艇身外形研究

采用SIMPLE算法、S-A湍流模型求解了三维不可压雷诺平均N-S方程,数值模拟了绕飞艇的低速不可压粘性流动,计算了不同艇身外形的阻力特性.本文方法计算结果与实验结果或其他文献的计算结果符合良好,可以用于飞艇的气动特性计算.通过对6个不同外形的相同体积飞艇阻力特性计算,得到了最佳艇身外形,表明本文方法可以用于艇身外形的选型设计.     

Modeling novel methodologies for unmanned aerial systems–Applications to the UAS-S4 Ehecatl and the UAS-S45 Bálaam

The rising demand for Unmanned Aerial Systems(UASs) to perform tasks in hostile environments has emphasized the need for their simulation models for the preliminary evaluations of their missions. The efficiency of the UAS model is directly related to its capacity to estimate its flight dynamics with minimum computational resources. The literature describes several techniques to estimate accurate aircraft flight dynamics. Most of them are based on system identification. This paper presents an alternative methodology to obtain complete model of the S4 and S45 unmanned aerial systems. The UAS-S4 and the UAS-S45 models were divided into four sub-models, each corresponding to a specific discipline: aerodynamics, propulsion, mass and inertia, and actuator. The‘‘aerodynamic" sub-model was built using the Fderivatives in-house code, which is an improvement of the classical DATCOM procedure. The ‘‘propulsion" sub-model was obtained by coupling a two-stroke engine model based on the ideal Otto cycle and a Blade Element Theory(BET) analysis of the propeller. The ‘‘mass and the inertia" sub-model was designed utilizing the Raymer and DATCOM methodologies. A sub-model of an actuator using servomotor characteristics was employed to complete the model. The total model was then checked by validation of each submodel with numerical and experimental data. The results indicate that the obtained model was accurate and could be used to design a flight simulator.     

A general calculation method to specify center-of-buoyancy for the stratospheric airship with multiple gas cells

As the lighter-than-air (LTA) flight vehicle, the stratospheric airship is a desirable platform to provide communication and surveillance services. During the ascent from sea-level to the mission altitude, the volume of the lifting gas may change significantly, which will result in the change of the center-of-buoyancy (CB). A general calculation method is developed to specify CB for the stratospheric airship with a double-ellipsoid hull and an arbitrary number of the gas cells. The cross-section-integral (CSI) method is used as a basic calculation scenario to specify CB. Considering the complexity in determining the boundary between the helium and air in the gas cell, a searching algorithm is put forward and the specification of CB can be conducted by the iterative calculation. As an important application, the stable condition of the pitch angle is analyzed when the change of CB is involved. Under different initial configurations, the stable pitch angle of the stratospheric airship during the ascent is specified and compared, which shows the advantages of the multi-gas-cell configuration. The results of this paper may provide an important reference for the engineering application of the stratospheric airship.     

Real-time object tracking via least squares transformation in spatial and Fourier domains for unmanned aerial vehicles

This paper addresses the problem of real-time object tracking for unmanned aerial vehicles. We consider the task of object tracking as a classification problem. Training a good classifier always needs a huge number of samples, which is always time-consuming and not suitable for realtime applications. In this paper, we transform the large-scale least-squares problem in the spatial domain to a series of small-scale least-squares problems with constraints in the Fourier domain using the correlation filter technique. Then, this problem is efficiently solved by two stages. In the first stage, a fast method based on recursive least squares is used to solve the correlation filter problem without constraints in the Fourier domain. In the second stage, a weight matrix is constructed to prune the solution attained in the first stage to approach the constraints in the spatial domain. Then, the pruned classifier is used for tracking. To evaluate proposed tracker's performance, comprehensive experiments are conducted on challenging aerial sequences in the UAV123 dataset. Experimental results demonstrate that proposed approach achieves a state-ofthe-art tracking performance in aerial sequences and operates at a mean speed of beyond 40 frames/s. For further analysis of proposed tracker's robustness, extensive experiments are also performed on recent benchmarks OTB50, OTB100, and VOT2016.     

无人机高速DS/FH混合扩频通信系统关键模块设计

针对UAV(Unmanned Aerial Vehicle,无人机)测控链路高抗干扰需求,给出了实现跳频速率20 000次/s的扩跳混合无人机测控数据链系统实现方案.系统采用跳频频率并行捕获模式.跳频源设计采用直接频率合成、DDS(Direct Digital Synthesis,直接数字频率合成)和PLL (Phase-Locked Loop,锁相环)相结合的混合频率合成技术.利用相位响应滤波器,通过正交调制技术完成MSK(Minimum Shift Keying,最小频移键控)、GMSK (GaussianMinimum Shift Keying,高斯最小频移键控)调制.通过推导得出2 bit差分解调输出与载波频率选择有关,且为四分之数据率的整数倍关系.然后通过实例分析给出了跳频频率间隔选取方法,即跳频间隔应当将临近跳频的主瓣分开,同时跳频载波频率应当设在其他跳频频谱的零点处.最后总结了高速扩跳频系统参数设计一般步骤.