Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

一种基于虚拟页地址映射的NAND Flash管理算法

本文提出了一种基于虚拟页地址映射的NAND Flash管理算法.该算法通过定义坏块表、对应表等结构，以及设计的坏块替换策略和虚拟页地址到实际物理页地址的转换算法，实现上层软件采用虚拟地址对NAND Flash的无坏块连续页地址访问.该算法是一种高效的地址映射算法，能高效地对数据进行索引，占用SRAM空间较少，使系统达到高性能，并使得闪存使用的更加稳定持久.     

Net110网吧安全审计管理系统的设计与实施

信息时代对公安管理系统提出了新的挑战，Net110网吧安全审计管理系统充分利用互联网络的技术特点，通过公安监察部门的电脑系统集中，统一和高效地管理在城区分散的网吧。本文着重阐述了系统设计的基本原理，并以南昌市公安局为例，介绍了从需求分析、系统设计到系统实施的建设全过程。     

智能控制大功率氨压机制冷系统

本文将模糊控制、神经元控制等智能控制技术成功地应用于大型活塞式氨压机制冷系统，实现了恒转矩负载的变频调速节能。实际运行结果证明，该智能控制的大功率氨压机制冷系统工作稳定、控制精度高、节能效果显著，具有很好的经济效益及推广应用价值。     

缠绕复合材料喷管静力分析

本文对由一般曲线旋转得到的喷管进行了静力分析。文中讨论的喷管由缠绕复合材料构成,承受轴对称和非轴对称载荷作用。在采用有限元法分析时,通过Fourier转换将三维问题简化为二维求解。弹性矩阵中各参数采用合理假设只需由层状平面内三个弹性常数即可确定。文中给出缠绕复合材料喷管在内压和集中力作用下的位移分布算例,结果合理。本文推荐方法可供缠绕柔性喷管和其它类似结构分析时参考。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

300M钢纯洁度磁粉检验磁痕现象的分析

采用交、直流磁粉检验并结合金相试验、电子探针试验及微量元素含量分析的方法，对３００Ｍ钢磁痕现象的本质进行了分析。结果表明，采用磁粉检验方法对航空优质钢进行纯洁度检验是可信的。     

国家财政主要支出项目与各项税收收入的最优化--回归分析在最优化中的应用研究实例

利用回归分析方法得到国家财政部分主要支出项目，部分税收收入与国内生产总值构成的回归方程，由此构成线性规划问题的约束方程组。再用M单纯形法求最优解。     

Petri网及其在FMS建模中的应用

本简要介绍了Petri网的原理，及其在FMS建模中的应用。