Research on navigation of satellite constellation based on an asynchronous observation model using X-ray pulsar

Pulsar navigation is a promising navigation method for high-altitude orbit space tasks or deep space exploration. At present, an important reason for restricting the development of pulsar navigation is that navigation accuracy is not high due to the slow update of the measurements. In order to improve the accuracy of pulsar navigation, an asynchronous observation model which can improve the update rate of the measurements is proposed on the basis of satellite constellation which has a broad space for development because of its visibility and reliability. The simulation results show that the asynchronous observation model improves the positioning accuracy by 31.48% and velocity accuracy by 24.75% than that of the synchronous observation model. With the new Doppler effects compensation method in the asynchronous observation model proposed in this paper, the positioning accuracy is improved by 32.27%, and the velocity accuracy is improved by 34.07% than that of the traditional method. The simulation results show that without considering the clock error will result in a filtering divergence.     

基于四元数估计角速率的陀螺故障定位

当卫星速率积分陀螺的配置冗余度不满足一致性检验条件时，不能单纯利用硬件冗余实现陀螺的故障定位。鉴于角度和角速度敏感器的输出通过卫星运动学相关，本文利用姿态测量敏感器的输出来诊断陀螺故障。首先根据姿态测量敏感器的输出得到卫星姿态四元数，进而根据四元数动力学方程得到粗略的姿态角速度信息，并将此角速度作为输出信息用于对卫星动力学方程的滤波，从而得到较精确的角速度信息，为单冗余度陀螺组件的故障定位提供解析冗余信息。利用四元数方法可以避免出现奇点。仿真结果证明了该方法的有效性。     

离散事件动态系统的GSMP模型及扰动分析

对离散事件动态系统（ＤＥＤＳ）的仿真过程建立了包含中断事件集和驱动事件集的广义半马尔可夫过程（ＧＳＭＰ）模型，对参数的无穷小扰动所引起的系统状态转移时刻进行了扰动分析，最后，讨论了扰动分析所需要的可变换条件和样本性能函数的关系，并提出值得进一步研究的问题。     

浮栅ROM器件的质子辐射效应实验研究

给出了浮栅ROM器件的质子辐射效应实验结果.认为浮栅ROM28C256和29C256的质子辐射效应不是单粒子效应,而是质子及其次级带电粒子产生的累积剂量造成的总剂量效应.器件出现错误有个质子注量阈值.对于29C256,高温加电退火容易消除质子产生的辐射损伤;对于28C256,高温加电退火不易消除质子产生的辐射损伤.动态监测和静态加电的器件都出现数据错误,且不能用编程器重新写入数据.然而不加电的器件在更高的质子注量辐照下未出现错误.对于应用浮栅ROM器件的航天器电子系统,冷备份是提高其可靠性的有效手段之一.     

事项法:提升财务会计核心竞争力的利器

信息技术对会计有着直接的影响，使会计从传统的簿记转变为关系数据库管理，企业资源计划，但同时大量非财务计量的涌现也降低了会计信息的权威，使其核心竞争力面临信息不客观、计量不完整、报告不及时等挑战。事项会计由于其强调个性化、增加信息量、减少抽象性、增强及时性、提高透明度的优势，成为提升会计核心竞争力的利器。由于计算机和网络技术的发展，计量属性研究的深入，会计环境的优化，以及信息使用者素质的提高，事项会计应用条件日益成熟，会计要保持核心竞争力，就必须逐步推行事项会计。     

火箭型单级入轨（SSTO）的初步分析

火箭型单级入轨（ＳＳＴＯ）是今后的发展方向之一，从多方面分析了火箭型单级入轨（ＳＳＴＯ）方案的可能性，简要回顾了ＳＳＴＯ的发展历史，特别对三角快帆（ＤＣ－Ｃｌｉｐｐｅｒ）作了分析，认为采取多项先进技术后是完全可以实现的。明确了单级入轨的两个基本方向：提高比冲和降低结构重量。分析了采用不同形式发动机的影响，列出了主要关键技术，最后提出了几个有参考价值的观点。     

离散事件系统的Petri网图仿真

1.前言 离散事件动态系统DEDS(Discrete Event Dynamic System)的传统分析方法——应用排队论和随机过程理论为离散事件动态系统建立排队网络模型,在很多情况下已不适用。新的理论和研究方法相继提出。其中之一是“皮特里网”(Petri Nets)理论。另一种比较成熟的方法是仿真法,但是,仿真法要以高昂的计算机设备的大量计算时间为代     

点焊质量模糊控制系统研究

简要介绍了电阻点焊单片机微机模糊控制原理，确定了点焊模糊控制算法，分析了点焊模糊控制系统的硬件结构和软件设计。实验结果表明，该控制系统能够有效实现点焊质量的模糊控制，具有较强的自适应特性，可用于电阻焊智能制造。     

Numerical investigation on flow nonuniformity-induced hysteresis in scramjet isolator

Numerical simulation and theoretical analysis were conducted to study the hysteresis inside scramjet isolator during the reciprocating process of back pressure variation. It is revealed that only a regular reflection is theoretically possible for two leading shocks when the inflow Mach number is greater than 2.0, and no hysteresis can occur in the transition between shock reflection types. Nevertheless, wall suction, gas injection, and background waves cause non-uniformity of the incoming flow and would make hysteresis possible. Besides the classical hysteresis in the transition between shock reflection, new kinds of hysteresis were found in both the deflection angle of separated boundary layer and the location of the shock train. Moreover, the occurrence of hysteresis in the deflection angle of the separated boundary layer is accompanied with the shock reflection hysteresis. In the case with background waves or gas injection, hysteresis in the starting position of leading shock was observed too. As back pressure decreases, the leading shock does not follow the same path as that as the back pressure increases, and it is anchored at the location where the background shock or the injection interacts with the leading shock. It is inferred that, if two strong adverse pressure gradient regions move towards and interact with each other, hysteresis will take place when they start to separate.     

Advances and trends in plastic forming technologies for welded tubes

With the implementation of environmental protection, sustainable development and conservation-oriented policies, components and parts of thin-walled welded tubes have gained increasing application in the aircraft and automotive industries because of their advantages: easily achieving forming and manufacturing process at low cost and in a short time. The current research on welded tube plastic forming is mainly concentrated on tube internal high-pressure forming, tube bending forming, and tube spinning forming. The focuses are on the material properties and characterization of welded tubes, finite element modeling for welded tube forming, and inhomogeneous deformation behavior and the mechanism and rules of deformation coordination in welded tube plastic forming. This paper summarizes the research progress in welded tube plastic forming from these aspects. Finally, with a focus on the urgent demand of the aviation, aerospace and automotive industries for high-strength and light-weight tubes, this paper discusses the development trends and challenges in the theory and technology of welded tube plastic forming in the future. Among them,laser tailor-welded technology will find application in the manufacture of high-strength steel tubes.Tube-end forming technology, such as tube flaring and flanging technology, will expand its application in welded tubes. Therefore, future studies will focus on the FE modeling regarding how to consider effects of welding on residual stresses, welding distortions and microstructure, the inhomogeneous deformation and coordination mechanism of the plastic forming process of tailor-welded tubes, and some end-forming processes of welded tubes, and more comprehensive research on the forming mechanism and limit of welded tubes.