压电智能结构传感器/作动器位置优化研究

研究压电主动结构振动控制当中传感器／作动器的位置优化问题。从系统的状态空间方程出发，在系统可控性、可观性Grammian矩阵特征值的基础上来描述性能指标，以控制能量最小化和传感能量最大化作为优化目标，利用遗传算法（GE）进行优化计算，计算过程中对传感器／作动器的位置采用二进制编码加以描述。通过对一压电板结构的仿真计算对该方法进行了验证，优化计算结果与枚举法结果完全相符，从而证明了方法的有效性。     

八作动器隔振平台的通道耦合分析及解耦控制

分析一种对称结构的八作动器隔振平台的通道耦合特性。分析表明由于结构对称，当有效载荷质心位于平台纵轴的延长线上，且有效载荷的惯性主轴与平台对称轴平行时，平台可分解成两个独立的单自由度系统和两个2阶耦合子系统。利用矩阵同时对角化方法对平台的2阶耦合子系统进一步解耦，仿真结果显示解耦控制能够衰减被动隔振的谐振峰，改进平台的隔振性能。     

采用共位配置的分布式压电敏感器和致动器的挠性结构振动控制

研究采用共位配置的分布式压电敏感器和致动器的挠性悬臂梁的振动控制问题，其中敏感器由压电聚乙二烯氟化物薄膜（PVDF）制成，致动器由压电陶瓷（PZT）或PVDF制成。本文首先建立系统的模型，设计了一种线性反馈控制方案，并应用无穷维空间的LaSalle不变原理，证明了相应闭环系统的渐近稳定性。     

基于特征模型的挠性悬臂板控制

针对航天器上太阳帆板这种悬臂外伸薄板结构的挠性附件 ,存在环境扰动下所引起的振动 ,本文采用压电智能结构作为执行器对悬臂板进行主动振动控制。基于板系统的特征建模 ,并结合自适应控制对挠性板的主动控制进行了研究。通过仿真研究结果与应变律反馈控制比较 ,表明该方法的有效性     

压电纤维复合材料的研究

以提高交叉指形电极压电纤维复合材料诱导应变和挟持应力为目的,采用有限元软件ANSYS分析了电极区聚合物参数、交叉指型电极结构和压电相体积分数对压电纤维复合材料诱导应变和挟持应力的影响。结果表明：增加电极区聚合物的介电常数或减小电极区聚合物的厚度,能够提高元件的诱导应变和挟持应力,元件诱导应变最大可达173με;减小分支电极的周期或者适当增大分支电极的宽度,可以有效地提高元件的作动性能;提高压电纤维体积分数,有利于提高元件的作动性能。     

Multi-mode optimal fuzzy active vibration control of composite beams laminated with photostrictive actuators

Firstly, a multi-field coupling finite element formulation of composited beam laminated with the photostrictive actuators is developed in this paper. Moreover, an optimal fuzzy active control algorithm is also proposed on the basis of the combination of optimal control and fuzzy one.This method opens a new avenue to resolve the contradiction between the linear system control method and nonlinear actuating characteristics of photostrictive actuators. The desired control for suppressing multi-modal vibration of photoelectric laminated beam is firstly obtained through optimal control and then the fuzzy control is used to approach the desired mechanical strain induced by photostrictive actuators. Thus, the multi-mode vibration control of beam is realized.In the design process of optimal fuzzy controller, the design of fuzzy control is independent of optimal control. The simulation results demonstrate that the proposed control method can effectively realize multi-modal vibration control of photoelectric laminated beams, and the control effect of optimal fuzzy control is better than that of optimal state feedback control.     

Hypervelocity impact induced shock acoustic emission waves for quantitative damage evaluation using in situ miniaturized piezoelectric sensor network

Manmade debris and natural meteoroids, travelling in the Low Earth Orbit at a speed of several kilometers per second, pose a severe safety concern to the spacecraft in service through the HyperVelocity Impact(HVI). To address this issue, an investigation of shock Acoustic Emission(AE) waves induced by HVI to a downscaled two-layer Whipple shielding structure is performed,to realize a quantitative damage evaluation. Firstly a hybrid numerical model integrating smoothparticle hydrodynamics and finite element is built to obtain the wave response. The projectiles, with various impact velocities and directions, are modelled to impact the shielding structure with different thicknesses. Then experimental validation is carried out with built-in miniaturized piezoelectric sensors to in situ sense the HVI-induced AE waves. A quantitative agreement is obtained between numerical and experimental results, demonstrating the correctness of the hybrid model and facilitating the explanation of obtained AE signals in experiment. Based on the understanding of HVI-induced wave components, assessment of the damage severity, i.e., whether the outer shielding layer is perforated or not, is performed using the energy ratio between the regions of ‘‘high frequency" and ‘‘low frequency" in the acquired AE signals. Lastly, the direct-arrival fundamentalsymmetric wave mode is isolated from each sensing signal to be input into an enhanced delay-andsum algorithm, which visualizes HVI spots accurately and instantaneously with different sensor network configuration. All these works demonstrate the potential of quantitative, in situ, and real time HVI monitoring using miniaturized piezoelectric sensor network.     

新型压电激励器作用力模拟技术研究

研究轻型结构、直升机旋翼结构和复合材料结构等的颤振飞行试验激励问题具有重要意义。提出以弯矩模拟压电粗纤维复合材料(MFC)激励器的作用力,从而解决MFC仿真建模问题。首先借助机翼有限元模型,建立带有压电激励器的机翼结构动力学仿真模型;然后以压电激励器地面激励试验结果为基础,通过修正仿真模型中压电作用弯矩的大小,实现仿真试验结果与地面试验结果的拟合,最终得出非线性压电激励器作用力;最后通过另一组地面试验数据验证了该作用力的大小,并将该作用力模拟技术应用于不同试验中。本文的研究结果可为后续以该激励器作为激励作动器或控制作动器的试验提供有益参考。     

电磁式作动器与受控结构的耦合特性研究

本文分析了电磁式作动器与受控结构的耦合特性。以某典型电磁式作动器为例,建立了它与恒流输出功率放大器、恒压输出功率放大器配套使用时的数学模型,以及它与受控结构的耦合模型,研究了受控结构耦合作用下电磁式作动器的频率特性,计算结果与试验结果一致。另外,本文还推荐将恒流输出功率放大器与电磁式作动器配合使用。     

Autonomous Control Reconfiguration of Aerospace Vehicle Based on Control Effectiveness Estimation

未来空天飞行器跨空天两域飞行,要求有较高的自主性以适应由故障和环境变化带来的不确定因素。针对空天飞行器的不确定性,提出了自主控制重构方案。研究了线性模型的时变控制效益的估计方法,提出并证明了效益矩阵可估计的充分条件,给出了相应的算法并证明了其收敛性和对噪声的鲁棒性;提出了基于线性规划和模糊逻辑的控制分配算法,通过冗余效应器实现了不确定条件下的自主控制重构。系统集成和仿真结果分析验证了方案和算法的有效性。