行星际结构与准平行无碰撞激波的相互作用

应用一维混合模拟方法数值研究了高密度等离子体团和行星际激波与准平行无碰撞激波的相互作用．结果表明，由于推平行无碰撞激波上游的大振幅低频波动的散射，除了在通过激波过渡区时稍有压缩外，等离子体团从激波的上游开始就一直是不断弥散的．行星际激波在向准平行无碰撞激波靠近的过程中，会在其上游产生大振幅的低频波动，同时行星际激波的强度不断增加，最后和准平行无碰撞激波会并成一个新的激波，在新激波前继续有大振幅的低频波动产生     

计算机帧时间对半实物仿真的影响

半实物仿真试验中,要求计算机帧时间与计算积分步长相一致,但在实际试验中不容易精确地做到。本文分析了这种不一致给半实物仿真试验带来的影响,给出了解决的办法,文章中还给出了一实例来说明。     

空间碎片防护结构设计优化理论方法研究

航天器空间碎片防护结构设计优化在国际上属前沿课题，防护结构设计优化理论方法是其关键技术之一。在防护优化理论模型及其优化算法研究方面取得了突破性进展，建立了综合各类典型防护结构构型的统一的防护优化数学模型，提出了解决防护优化问题的几种算法：混合遗传算法，改进的差异演化算法和混合差异演化算法。最后采用航天器防护优化算例对防护优化理论方法进行了测试考核，优化结果表明了本文工作的可行性和有效性。     

Radiative and hybrid cooling of infrared space telescopes

The designs of cold space telescopes, cryogenic and radiatively cooled, are similar in most elements and both benefit from orbits distant from the Earth. In particular such orbits allow the anti-sunward side of radiatively-cooled spacecraft to be used to provide large cooling radiators for the individual radiation shields. Designs incorporating these features have predictedT _tel near 20 K. The attainability of such temperatures is supported by limited practical experience (IRAS, COBE). Supplementary cooling systems (cryogens, mechanical coolers) can be advantageously combined with radiative cooling in hybrid designs to provide robustness against deterioration and yet lower temperatures for detectors, instruments, and even the whole telescope. The possibility of such major additional gains is illustrated by the Very Cold Telescope option under study forEdison, which should offerT _tel5 K for a little extra mechanical cooling capacity.     

Three-dimensional numerical analysis on combustion performance and flow of hybrid rocket motor with multi-segmented grain

This paper presents the combustion characteristics in hybrid rocket motors with multi-segmented grain through three-dimensional numerical simulations. Multi-segmented grain is composed of several thin grains with two or more ports. The numerical model consists of Navier-Stokes equations with turbulence, solid fuel pyrolysis, chemical reactions, a fluid–solid coupling model and a regression rate model. The simulations adopt 90% Hydrogen Peroxide (HP) and PolyEthylene (PE) as the propellant combination. The effects of the rotation, port number, fuel grain segment number and mid-chamber length on the flow field and combustion performances are analyzed. The results indicate that the multi-segmented grain configuration can strengthen the flow field, and the regression rate and combustion efficiency are enhanced. Take the cases with two grain segments and three ports for example, the regression rate is increased by 32.4%−45.1% and the combustion efficiency increases by 6%−8.6% in different rotation angles.     

Plastic wrinkling prediction in thin-walled part forming process:A review

The precision forming of thin-walled components has been urgently needed in aviation and aerospace field. However, the wrinkling induced by the compressive instability is one of the major defects in thin-walled part forming. The initiation and growth of the wrinkles are interac-tively affected by many factors such as stress states, mechanical properties of the material, geometry of the workpiece and boundary conditions. Especially when the forming process involves compli-cated boundary conditions such as multi-dies constrains, the perturbation of clearances between workpiece and dies and the contact conditions changing in time and space, etc., the predication of the wrinkling is further complicated. In this paper, the current prediction methods were summa-rized including the static equilibrium method, the energy method, the initial imperfection method, the eigenvalue buckling analysis method, the static-implicit finite element method and the dynamic-explicit finite element method. Then, a systematical comparison and summary of these methods in terms of their advantages and limitations are presented. By using a combination of explicit FE method, initial imperfection and energy conservation, a hybrid method is recommended to predict plastic wrinkling in thin-walled part forming. Finally, considering the urgent requirements of com-plex thin-walled structures’ part in aviation and aerospace field, the trends and challenges in wrin-kling prediction under complicated boundary conditions are presented.     

Machining of a film-cooling hole in a single-crystal superalloy by high-speed electrochemical discharge drilling

Single-crystal superalloys are typical advanced materials used for manufacturing aeroengine turbine blades. Their unique characteristics of high hardness and strength make them exceedingly difficult to machine. However, a key structure of a turbine blade, the film-cooling hole,needs to be machined in a single-crystal superalloy; such machining is challenging, especially considering the increasing levels of machining efficiency and quality demanded by the aeroengine industry. Tube electrode high-speed electrochemical discharge drilling(TSECDD), a hybrid technique of high-speed electrical discharge drilling and electrochemical machining, provides high machining efficiency and accuracy, as well as eliminating the recast layer. In this study, TSECDD is used to machine a film-cooling hole in a nickel-based single-crystal superalloy(DD6). The Taguchi methods of experiment are used to optimise the machining parameters. Experimental results show that TSECDD can effectively drill the film-cooling hole; the optimum parameters that give the best performance are as follows: pulse duration: 12 ls, pulse interval: 30 ls, peak current:6 A, and salt solution conductivity: 3 m S/cm. Finally, a hole is machined by TSECDD, and the results are compared with those obtained by electrical discharge machining. TSECDD is found to be promising for improving the surface quality and eliminating the recast layer.     

叶片磨抛机器人力/位混合控制的设计与实现

为提高航空类发动机叶片的自动化磨抛精度,减小复杂曲面叶片加工轨迹控制误差,采用基于六维力传感器的机器人力/位混合控制策略,实现机器人磨抛轨迹的在线修正。搭建以Staubli机器人和ATI六维力传感器为核心部件的叶片磨抛验证平台,通过C++开发上位机,采集磨抛过程中六维力传感器信息并进行Kalman滤波。通过示教确定机器人运动轨迹,对机器人运动轨迹与力传感器信息进行采集分析,确定基于力/位混合控制可以实现机器人运动轨迹的在线修正,为复杂曲面的叶片磨抛轨迹控制提供一种解决方案。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Streamwise-body-force-model for rapid simulation combining internal and external flow fields

A streamwise-body-force-model (SBFM) is developed and applied in the overall flow simulation for the distributed propulsion system, combining internal and external flow fields. In view of axial stage effects, fan or compressor effects could be simplified as body forces along the streamline. These body forces which are functions of local parameters could be added as source terms in Navier-Stokes equations to replace solid boundary conditions of blades and hubs. The val-idation of SBFM with uniform inlet and distortion inlet of compressors shows that pressure perfor-mance characteristics agree well with experimental data. A three-dimensional simulation of the integration configuration, via a blended wing body aircraft with a distributed propulsion system using the SBFM, has been completed. Lift coefficient and drag coefficient agree well with wind tun-nel test results. Results show that to reach the goal of rapid integrated simulation combining inter-nal and external flow fields, the computational fluid dynamics method based on SBFM is reasonable.